Sherwood Newcastle R-965 Installations- und Betriebshandbuch

1. Write down all the custom settings you have memorized in your unit as they will be lost during the upgrade

procedure.

2. Download the upgrade files from Sherwood’s web site, www.sherwoodusa.com and unzip the files to a new

directory on your computer. Click ‘Set up.exe’ in order to install the update program on your computer.

3. With the AC cord unplugged, set the OPR/SVC switch located on the rear panel to the SVC position.

4. Connect the AC cord between the receiver and the wall outlet.

5. Power on the receiver by pressing the Power button and check that the standby buttons shows an orange LED.

6. Connect the receiver to computer with RS232 or USB cable.

7. Note:

1) If you are using RS232C for upgrade, go to Step 8 below.

2) If this is your first time to upgrade via USB, you need to install the Sherwood USB driver in your computer

first. Driver installation is needed for the first trial only. For a detailed installation guide, refer to the help file

in the upgrade application program.

8. Run the ‘Sherwood Receiver Firmware Upgrade program’.

(Note : program version may be updated without prior notice for better customer support)

9. Click the ‘Port Setting’ button to set up the port.

Note: The port setting is not needed when using a USB connection for the upgrade. Your computer should

automatically detect the USB connection and will show the following screen instead. After confirming this

screen, go to step 12.

10. A Pop-up Window will appear as below. (Default : COM1/9600). Based on your actual computer settings,

you may change the COM port setting but the baud rate must be 9600.

11. Click the ‘OK’ button. Then the computer will show the window as below.

12. Click the ‘File Open’ button in order to open BIN file.

Note: (It is recommended to save the .BIN file in a specific folder. The default setting is C:\Program

files\Sherwood receiver)

13. Click the ‘Upgrade’ button to start the firmware update.

14. If you receive the message below it means the upgrade failed. In this case, just power the receiver off

and then on rapidly (within 1 second) for a reset. After the reset, click ”OK” on the ERROR message and then click

the “Upgrade” button, again.

Note : The ‘Device Restart’ message means something is wrong or failed in the above procedure. In case of

this message, check your cable or COM port. If the connection is good, turn the Newcastle unit off and then on

again and re-try the upgrade procedure from step 13 above.

15. ‘Program Success!’ message means the update is complete.

16. Exit the update program.

17. Power off the receiver and set OPR/SVC switch on the rear panel to the OPR position.

18. Power on the receiver. With the receiver still in the “STANDBY” mode (orange LED visible), hold the

‘ROOM2’ button and ‘TONE MODE’ button simultaneously to re-set the microprocessor. Turn on the

receiver by pressing the ‘STANDBY’ button. (Blue LED)

19. If the display reads ‘FM 87.5MHZ’ the re-set was completed successfully. If not, repeat Step 18.

20. Once you have finished the upgrade and reset process, you will need to program the unit’s settings according

to the devices you have connected.

If you have problems and cannot load the new firmware, please contact Sherwood technical support at (800) 962-

3203 ext 115. This number is available during normal business hours, 8:00 AM to 5:00 PM, Monday to Friday,

Pacific time.

Andere Handbücher für Newcastle R-965

Inhaltsverzeichnis

Andere Sherwood Empfänger Handbücher

Sherwood

Sherwood RX-2060R Bedienungsanleitung

Sherwood

Sherwood R-765 Bedienungsanleitung

Sherwood

Sherwood RD-7500 Bedienungsanleitung

Sherwood

Sherwood Newcastle HSB-6501 Bedienungsanleitung

Sherwood

Sherwood Newcastle R-965 Betriebsanleitung

Sherwood

Sherwood RD-7502 Bedienungsanleitung

Sherwood

Sherwood NewCastle R-945 Bedienungsanleitung

Sherwood

Sherwood RD-6504 Bedienungsanleitung

Sherwood

Sherwood VR-758 Bedienungsanleitung

Sherwood

Sherwood RD-8504 Bedienungsanleitung

Sherwood

Sherwood RV-5050RDS Bedienungsanleitung

Sherwood

Sherwood Newcastle VR-654BD Bedienungsanleitung

Sherwood

Sherwood R-774 Bedienungsanleitung

Sherwood

Sherwood R-904 Bedienungsanleitung

Sherwood

Sherwood NewCastle R-945 Bedienungsanleitung

Sherwood

Sherwood Newcastle R-863 Bedienungsanleitung

Sherwood

Sherwood Newcastle P-965 Bedienungsanleitung

Sherwood

Sherwood NetBoxx R-904N Bedienungsanleitung

Sherwood

Sherwood RD-8504 Bedienungsanleitung

Sherwood

Sherwood RD-7108 Bedienungsanleitung

Sherwood

Sherwood NewCastle R-945 Bedienungsanleitung

Sherwood

Sherwood R-807 Bedienungsanleitung

Sherwood

Sherwood RD-7405HDR Bedienungsanleitung

Sherwood

Sherwood R-125 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung

Dish Network

Dish Network Satellite Television Bedienungsanleitung