Shure ANIUSB-Matrix Bedienungsanleitung

ANIUSB-Matrix

Audio Network Interface

Complete user guide for the ANIUSB-MATRIX. Includes system diagrams, specifications, installation instructions, command strings, and

more.

Version: 6 (2020-B)

Shure Incorporated
2/31
Table of Contents
ANIUSB-MatrixAudio Network Interface 3
Safety Information 3
IMPORTANT SAFETY INSTRUCTIONS 3
General Description 4
Getting Started 4
Step 1: Connect to a Network 4
Step 2: Discover the ANIUSB-MATRIX in Designer 4
Step 3: Route Audio to the ANIUSB-MATRIX 5
Step 4: Configure Audio 6
Get More Information 6
Differences Between 3.x and 4.x Firmware 6
Hardware and Installation 7
Rear Panel 7
Power Over Ethernet (PoE) 9
Reset 9
Installation and Rack Mounting 9
Controlling Devices with Shure Designer Software 12
Device Identification 12
Overview of Shure Conferencing Devices 12
Signal Flow and Connections 13
Connections and Signal Flow 14
Connecting a USB Device 15
Audio Settings 15
Schematic View 15
Mute and Fader Groups 17
Adjusting Input levels 17
Adjusting Output Levels 17
Parametric Equalizer 17
Custom Presets 20
Matrix Mixer 21
Crosspoint Gain 21
Routing Channels 21
ANIUSB-MATRIX Default Settings 21
Mute Synchronization 22
Setting Up Mute Sync on the MXA310 and ANIUSB-MA-
TRIX 23
Encryption 23
Networking and Dante 23
Dante Transmit Flows 23
Pushing Device Names to the Dante Network 24
Compatibility with Dante Domain Manager 24
IP Ports and Protocols 24
Using a Third-Party Control System 25
Troubleshooting 25
Event Log 26
Important Product Information 27
Information to the user 27
Specifications 28
Accessories 30
Furnished Accessories 31
Optional Accessories and Replacement Parts 31

Shure Incorporated

3/31

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

ANIUSB-Matrix

Audio Network Interface

Safety Information

IMPORTANT SAFETY INSTRUCTIONS

READ these instructions.

KEEP these instructions.

HEED all warnings.

FOLLOW all instructions.

DO NOT use this apparatus near water.

CLEAN ONLY with dry cloth.

DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance

with the manufacturer’s instructions.

DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in-

cluding amplifiers) that produce heat. Do not place any open flame sources on the product.

DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third

prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-

ment of the obsolete outlet.

PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

ONLY USE attachments/accessories specified by the manufacturer.

USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

UNPLUG this apparatus during lightning storms or when unused for long periods of time.

REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any

way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the

apparatus.

The MAINS plug or an appliance coupler shall remain readily operable.

The airborne noise of the Apparatus does not exceed 70dB (A).

Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec-

tion.

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.

Operate this product within its specified operating temperature range.

Shure Incorporated

4/31

•

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accom-

panying this unit.

General Description

The ANIUSB-MATRIX Audio Network Interface provides connections for USB, Dante , and analog audio sources. Collaborate

and connect with all audio devices on a single network, with support for wireless microphones, computers, mobile devices,

video codecs, and loudspeaker systems. Connect with a single network cable to receive audio and power through Power over

Ethernet (PoE). Use Shure Designer software to control audio and network settings from any computer connected to the same

network.

Getting Started

To control the ANIUSB-MATRIX, use Shure Designer software to adjust settings and route audio between Shure devices. After

completing this basic setup process, you should be able to:

Control the ANIUSB-MATRIX in Designer

Route audio to the ANIUSB-MATRIX in Designer

Use the matrix mixer to route audio signals

Before you get started, you'll need:

Cat5e (or better) Ethernet cable

Network switch that provides Power over Ethernet (PoE)

Shure Designer software installed on a computer. Download at www.shure.com.

Step 1: Connect to a Network

Connect the ANIUSB-MATRIX to a PoE port on the network switch using Cat5e (or better) cable.

Connect your computer running Designer to the network switch.

Step 2: Discover the ANIUSB-MATRIX in Designer

Open Designer, and check that you’re connected to the correct network in Settings.

Click Online devices. A list of online devices appears.

™

Shure Incorporated

5/31

◦

To identify devices, click the product icon to flash the lights on a device. Select the ANIUSB-MATRIX in the list and click

Configure to open the device's configuration window.

Step 3: Route Audio to the ANIUSB-MATRIX

To route audio in Designer, you’ll need to create a project and a location. You can learn more about both in Designer’s Help

section.

For this example, we’ll connect an MXA310 table array microphone.

From My projects, select New to create a new project.

Click New to add a Location to your project. Once you enter a name, a new window for the location opens.

Click Live mode. Any online devices appear in the list.

In Designer, you can also design systems with virtual devices and send settings to real devices. Learn more in

Designer’s Help section.

Drag and drop the ANIUSB-MATRIX to add it to your location. Add the MXA310 to the same location.

Go to Signal flow. This page creates Dante audio routes between Shure devices.

Note: To route audio to non-Shure devices, use Dante Controller software.

Drag and drop from the MXA310 automix output to the ANIUSB-MATRIX Dante input to create Dante audio routes.

Shure Incorporated

6/31

•

Step 4: Configure Audio

The final configuration steps will vary, depending on what other devices you connect to the ANIUSB-MATRIX. These are gener-

al guidelines, but you’ll find more details in the system examples.

Connect other analog and USB devices to the ANIUSB-MATRIX. If you have a computer with video conferencing soft-

ware, connect it to the USB port.

Go to Matrix mixer to route audio between ANIUSB-MATRIX inputs and outputs. You can send a single input to many

outputs or vice versa. To send audio from the MXA310 to the computer, check the box where Dante Input 1 and USB

Output intersect.

Perform a sound check and adjust input and output levels in Designer.

Apply equalization (EQ) as needed to improve speech clarity.

Get More Information

Now that the basic setup is complete, you should have access to the ANIUSB-MATRIX in Designer and be able to pass audio.

Learn more about the ANIUSB-MATRIX in the Designer Help section or in the complete user guide at pubs.shure.com/guide/

ANIUSB-Matrix.

Differences Between 3.x and 4.x Firmware

Support for Dante Domain Manager

You can now add the ANIUSB-MATRIX to domains in Dante Domain Manager software.

Shure Incorporated

7/31

•

Audio Encryption Improvements

Firmware 4.x and newer has improved audio encryption, so make sure to update all Shure devices using encryption to the

same major firmware version.

Web Applications Removed

With firmware 4.x and newer, Shure Designer software is the only way to control the ANIUSB-MATRIX.

You can access basic settings for the device by opening it from the Shure Web Device Discovery tool, but you must use

Designer for full control.

Download Designer at shure.com/designer.

Hardware and Installation

Rear Panel

①Level Indicators (Signal/Clip)

Tri-color LEDs indicate the audio signal level for the analog channels and connectivity status for the USB channel. Adjust out-

put levels in Shure Designer software to avoid clipping.

Analog Input/Output

LED State Audio Signal Level

Off less than -60 dBFS

Green -59 dBFS to -24 dBFS

Yellow -23 dBFS to -1 dBFS

Red 0 dBFS or more

Note: The input and output LEDs stay off when metering is set to Post-gain.

USB Audio

LED State Status

Off No USB device connected

Shure Incorporated

8/31

LED State Status

Green USB device operating successfully

Red (flashing) Problem detected with connected USB audio device

②Audio Input (Block Connector)

Block Pin Assignments:

Audio +

Audio -

Audio ground

③Chassis Ground Screw

Provides an optional connection for microphone shield wire to chassis ground.

④Audio Output (Block Connector)

Balanced audio output connects to an analog device. Set the output level in Shure Designer software to match the input

sensitivity of the analog device.

Note: See front panel labels for block connector assignments.

⑤USB Port

Connects to a computer to send and receive any combination of input and output audio channels.

⑥LED Indicators

Power: Power over Ethernet (PoE) present

Note: Use a PoE injector if your network switch does not supply PoE.

Network: Network connection active

Network Audio: Dante audio present on the network

Note: Error details are available in the event log in Shure Designer software.

Network Audio LED Behavior

LED Status Activity

Off No active signal

Green Device is operating successfully

Red Error has occurred. See event log for details.

Encryption:

LED Status Activity

Off Audio not encrypted

Green Successful encrypted audio connection with another device

Shure Incorporated

9/31

•

LED Status Activity

Red

Encryption error. Possible causes:

Encryption is enabled on one device and not on another

Passphrase mismatch

⑦Dante Network Port

Connects to a network switch to receive Dante audio, Power over Ethernet (PoE), and data from the control software.

⑧Reset Button

Resets the device settings back to the factory default.

Power Over Ethernet (PoE)

This device requires PoE to operate. It is compatible with both Class 0 and Class 3 PoE sources.

Power over Ethernet is delivered in one of the following ways:

A network switch that provides PoE

A PoE injector device

Reset

The reset button is located inside a small hole in the rear panel. Use a paperclip or other small tool to press the button.

There are two hardware reset functions:

Network reset (press button for 4-8 seconds)

Resets all Shure control and audio network IP settings to factory defaults

Full factory reset (press button for longer than 8 seconds)

Restores all network and Designer settings to the factory defaults.

Software Reset Options

To simply revert settings without a complete hardware reset, use one of the following options:

Reboot Device:Power-cycles the device as if it were unplugged from the network. All settings are retained when the device is

rebooted.

Default Settings: To revert audio settings back to the factory configuration (excluding Device Name, IP Settings, and Pass-

words), select Load Preset and choose the default settings preset.

Installation and Rack Mounting

Two mounting solutions are available for installing the Audio Network Interface:

CRT1 19" Rack Tray (optional accessory): Supports up to 3 devices; mountable in a rack or under a table

Single-unit Mounting Tray (included accessory): Supports a single device for mounting under a table

Securing the Devices

Use the included screws from the mounting hardware kit to secure the Audio Network Interfaces. Audio Network Interfaces can

be mounted to face either direction. Insert the screws from the bottom in the appropriate holes, according to the following dia-

grams:

Shure Incorporated

10/31

Align the holes as shown for securing a single device in the single-unit mounting tray

Align the holes as shown for securing up to 3 devices in the 19" rack tray.

Rack Ear Configuration

A combination of up to 3 Audio Network Interfaces can be mounted in a single 19-inch rack space. The adjustable rack ears

support mounting in a standard equipment rack or underneath a table.

Standard 19" Rack Mount

Align the ears with the mounting holes pointed forward.

Install the 3 screws that hold the ear to the tray as shown.

Andere Handbücher für ANIUSB-Matrix

Inhaltsverzeichnis

Andere Shure Aufnahmegeräte Handbücher

Shure

Shure ANI4IN Series Bedienungsanleitung

Shure

Shure 44 Series Bedienungsanleitung

Shure

Shure PSM 300 Bedienungsanleitung

Shure

Shure PSM 900 Bedienungsanleitung

Shure

Shure M97xE Bedienungsanleitung

Shure

Shure PSM1000 Bedienungsanleitung

Shure

Shure M55E Bedienungsanleitung

Shure

Shure Microphone Level Tone Generator A15TG Bedienungsanleitung

Shure

Shure PSM 300 Bedienungsanleitung

Shure

Shure M78S Bedienungsanleitung

Shure

Shure 35 Series Bedienungsanleitung

Shure

Shure PSM 900 Programmierhandbuch

Shure

Shure MVI Bedienungsanleitung

Shure

Shure M625 Bedienungsanleitung

Shure

Shure ANI22 Bedienungsanleitung

Shure

Shure LEGENDARY PERFOMANCE MVi Bedienungsanleitung

Shure

Shure PSM700 Bedienungsanleitung

Shure

Shure MVI Bedienungsanleitung

Shure

Shure ANI4OUT Bedienungsanleitung

Shure

Shure ANIUSB-Matrix Bedienungsanleitung

Shure

Shure PSM 600 Bedienungsanleitung

Shure

Shure Access Bedienungsanleitung

Shure

Shure AMS880 Bedienungsanleitung

Shure

Shure A820-NIC-DANTE Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch