Shure ANI22 Bedienungsanleitung

ANI22

Audio Network Interface

Complete user guide for the ANI22. Includes system diagrams, specifications, installation instructions, command strings, and more.

Version: 3 (2020-B)

Shure Incorporated
2/27
Table of Contents
ANI22Audio Network Interface 3
Safety Information 3
IMPORTANT SAFETY INSTRUCTIONS 3
General Description 4
Getting Started 4
Step 1: Connect to a Network 4
Step 2: Access the Web Application 4
Step 3: Connect Devices in Dante Controller Software 5
Step 4: Configure Audio 5
Get More Information 6
Hardware and Installation 6
Hardware 7
Power Over Ethernet (PoE) 9
Reset 9
Installation and Rack Mounting 10
Signal Flow and Connections 12
Connections and Signal Flow 12
Summing 13
Encryption 14
Logic Applications 14
Device Identification 15
Audio Settings 15
Adjusting Input levels 15
Adjusting Output Levels 16
Metering Options (Pre-gain and Post-gain) 16
Parametric Equalizer 16
Custom Presets 19
Networking and Dante 20
Dante Transmit Flows 20
Pushing Device Names to the Dante Network 20
Compatibility with Dante Domain Manager 20
QoS (Quality of Service) Settings 20
IP Ports and Protocols 21
Event Log 22
Using a Third-Party Control System 23
Important Product Information 23
Information to the user 23
Certifications 24
Specifications 24
Accessories 26
Furnished Accessories 27
Optional Accessories and Replacement Parts 27

Shure Incorporated

3/27

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

ANI22

Audio Network Interface

Safety Information

IMPORTANT SAFETY INSTRUCTIONS

READ these instructions.

KEEP these instructions.

HEED all warnings.

FOLLOW all instructions.

DO NOT use this apparatus near water.

CLEAN ONLY with dry cloth.

DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance

with the manufacturer’s instructions.

DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in

cluding amplifiers) that produce heat. Do not place any open flame sources on the product.

DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third

prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace

ment of the obsolete outlet.

PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

ONLY USE attachments/accessories specified by the manufacturer.

USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

UNPLUG this apparatus during lightning storms or when unused for long periods of time.

REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any

way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the

apparatus.

The MAINS plug or an appliance coupler shall remain readily operable.

The airborne noise of the Apparatus does not exceed 70dB (A).

Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec

tion.

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.

Operate this product within its specified operating temperature range.

Shure Incorporated

4/27

•

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accom

panying this unit.

General Description

The Shure ANI22 Audio Network Interface provides 2 channels of Dantetoanalog and 2 channels of analogtoDante conver

sion. A single interface provides a simple way to connect analog equipment to the audio network, such as wireless micro

phones, audio processors, video codecs, and loudspeaker systems. Available in XLR and block connector versions, each box

uses a single network cable to carry audio and power through Power over Ethernet (PoE). A browser-based web application

controls audio and network settings from any computer connected to the same network.

Getting Started

This device features a browser-based web application, which controls audio and network properties. Upon completing this ba

sic setup process, you will be able to:

Access the web application to customize audio settings and network properties

Use Dante Controller software to connect with other Dante devices and pass audio

Access additional configuration information

Step 1: Connect to a Network

Use an Ethernet cable (CAT5e or higher) to connect the ANI22 to a network switch.

Note: The network switch must provide Power over Ethernet (PoE). Make sure to connect to a PoE port, since many switches do not supply power

on all ports.

Connect a computer to the network switch with an Ethernet cable

Step 2: Access the Web Application

Download and install the Shure Device Discovery application (http://www.shure.com)

Open the Shure Device Discovery application

™

Shure Incorporated

5/27

Double-click the device to open the web application.

Tip: If setting up multiple Shure devices, use the Identify button in the application to flash the lights on the device.

Step 3: Connect Devices in Dante Controller Software

Download and install Dante Controller Software from http://www.audinate.com

Use Dante Controller to create connections with other Dante devices

Note: Refer to the Dante Controller user guide for more information on channel routing (available at http://www.audinate.com/resources/technicaldocumenta

tion)

Example: Connecting the ANI22 and Shure MXA310

Find the MXA310 in the list of Dante transmitters, and select the plus sign (+) to show all channels.

Find the ANI22 in the list of Dante receivers, and select the plus sign (+) to show all channels.

Check the box where the MXA310 AUTOMIX OUT and the ANI22 DANTE INPUT 1 intersect

Step 4: Configure Audio

Connect analog equipment (such as loudspeakers or wireless microphone systems) to the analog inputs and outputs.

Refer to the hardware section in this guide for information on connections and LED metering.

Shure Incorporated

6/27

•

In the ANI22 web application, adjust input and output levels and perform a sound check. Refer to the help topics in the

web application for additional information.

Get More Information

Now that the basic setup is complete, you should have access to the web application and be able to pass audio between de

vices. More comprehensive information is available online and in the help section, including:

Maximizing audio quality with the built-in parametric equalizer

External control system command strings

System scenario diagrams

Software configuration

Networking information

Troubleshooting

Replacement parts and accessories

The complete user guide is available at http://pubs.shure.com/guide/ANI22

Shure Incorporated

7/27

◦

Hardware and Installation

Hardware

Block Connector Model:

XLR Model:

①Signal/Clip Indicators

Each indicator corresponds to a single channel. Analog and digital gain adjustments are made through the web application.

If an input channel LED turns red, attenuate the level from the source device to prevent clipping at the input stage.

If an output channel LED turns red, lower the corresponding Digital Gain (dB) fader for the Dante channel under the Input

Channels tab. Do not lower the output level (line/aux/mic), as any clipping indicated on the LED occurs before the final out

put level stage.

Shure Incorporated

8/27

LED State Audio Signal Level

Off less than -60 dBFS

Green -59 dBFS to -24 dBFS

Yellow -23 dBFS to -1 dBFS

Red 0 dBFS or more

②Audio and Logic Connections

Note: Logic connections are only featured on the block connector version.

Block Connector Pin Assignments:

Input

Audio +

Audio -

Audio ground

switch Logic Mute (sent from microphone)

led Logic LED (received by microphone)

gnd Logic ground

Output

Audio +

Audio -

Audio ground

XLR Pin Assignments:

1Ground

2Positive

3Negative

③Chassis Ground Screw

Provides an optional connection for microphone shield wire to chassis ground.

④LED Indicators

Power: Power over Ethernet (PoE) present

Note: Use a PoE injector if your network switch does not supply PoE.

Network: Network connection active

Network Audio: Dante audio present on the network

Note: Error details are available in the event log in the web application.

Shure Incorporated

9/27

•

LED Status Activity

Off No active signal

Green Device is operating successfully

Red Error has occurred. See event log for details.

Encryption:

LED Status Activity

Off Audio not encrypted

Green Successful encrypted audio connection with another device

Red

Encryption error. Possible causes:

Encryption is enabled on one device and not on another

Passphrase mismatch

⑤Dante Network Port

Connects to a network switch to send Dante audio, while receiving Power over Ethernet (PoE) and data from the control

software. See the Dante and networking section for additional information.

⑥Reset Button

Resets the device settings back to the factory default.

Power Over Ethernet (PoE)

This device requires PoE to operate. It is compatible with both Class 0 and Class 3 PoE sources.

Power over Ethernet is delivered in one of the following ways:

A network switch that provides PoE

A PoE injector device

Reset

The reset button is located inside a small hole in the rear panel. Use a paperclip or other small tool to press the button.

There are two hardware reset functions:

Network reset (press button for 4-8 seconds)

Resets all Shure control and audio network IP settings to factory defaults

Full factory reset (press button for longer than 8 seconds)

Restores all network and Designer settings to the factory defaults.

Software Reset Options

To simply revert settings without a complete hardware reset, use one of the following options:

Reboot Device:Power-cycles the device as if it were unplugged from the network. All settings are retained when the device is

rebooted.

Shure Incorporated

10/27

Default Settings: To revert audio settings back to the factory configuration (excluding Device Name, IP Settings, and Pass

words), select Load Preset and choose the default settings preset.

Installation and Rack Mounting

Two mounting solutions are available for installing the Audio Network Interface:

CRT1 19" Rack Tray (optional accessory): Supports up to 3 devices; mountable in a rack or under a table

Single-unit Mounting Tray (included accessory): Supports a single device for mounting under a table

Securing the Devices

Use the included screws from the mounting hardware kit to secure the Audio Network Interfaces. Audio Network Interfaces can

be mounted to face either direction. Insert the screws from the bottom in the appropriate holes, according to the following dia

grams:

Align the holes as shown for securing a single device in the single-unit mounting tray

Align the holes as shown for securing up to 3 devices in the 19" rack tray.

Rack Ear Configuration

A combination of up to 3 Audio Network Interfaces can be mounted in a single 19-inch rack space. The adjustable rack ears

support mounting in a standard equipment rack or underneath a table.

Standard 19" Rack Mount

Align the ears with the mounting holes pointed forward.

Install the 3 screws that hold the ear to the tray as shown.

Andere Handbücher für ANI22

Inhaltsverzeichnis

Andere Shure Aufnahmegeräte Handbücher

Shure

Shure 35 Series Bedienungsanleitung

Shure

Shure DT15P Bedienungsanleitung

Shure

Shure PSM1000 Technisches Handbuch

Shure

Shure A820-NIC-DANTE Bedienungsanleitung

Shure

Shure ANI22 Bedienungsanleitung

Shure

Shure M75ECS Bedienungsanleitung

Shure

Shure PSM 300 Bedienungsanleitung

Shure

Shure Microphone Level Tone Generator A15TG Bedienungsanleitung

Shure

Shure PSM 300 Bedienungsanleitung

Shure

Shure MVI Bedienungsanleitung

Shure

Shure PS9 Bedienungsanleitung

Shure

Shure 44 Series Bedienungsanleitung

Shure

Shure M78S Bedienungsanleitung

Shure

Shure PSM1000 Bedienungsanleitung

Shure

Shure PSM 200 Kurzanleitung

Shure

Shure DFR11EQ Version 5 Bedienungsanleitung

Shure

Shure ANI4IN Series Bedienungsanleitung

Shure

Shure PSM 900 Programmierhandbuch

Shure

Shure DFR11EQ Version 5 Bedienungsanleitung

Shure

Shure P3RA Bedienungsanleitung

Shure

Shure MV88+ Bedienungsanleitung

Shure

Shure R180 Bedienungsanleitung

Shure

Shure MVX2U Bedienungsanleitung

Shure

Shure DFR11EQ Version 5 Stücklistenhandbuch

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch