Shure AD1 Bedienungsanleitung

1/24

AD1 -- Bodypack Transmitter

WARNING

• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disas

semble, heat above 140°F (60°C), or incinerate.

•Follow instructions from manufacturer

•Only use Shure charger to recharge Shure rechargeable batteries

•WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.

•Never put batteries in mouth. If swallowed, contact your physician or local poison control center

•Do not short circuit; may cause burns or catch fire

•Do not charge or use battery packs other than Shure rechargeable batteries

•Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.

•Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or

the like

WARNING: Danger of explosion if incorrect battery replaced. Operate only with AA batteries.

Note: Use only with the included power supply or a Shure-approved equivalent.

Please follow your regional recycling scheme for batteries, packaging, and electronic waste.

WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or

other reproductive harm.

低功率電波輻射性電機管理辦法

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計

之特性及功能。第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時

方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學

及醫療用電波輻射性電機設備之干擾。

AD1 Axient Digital Bodypack Transmitter

AD series bodypack transmitters deliver impeccable audio quality and RF performance with wide-tuning, High

Density (HD) mode, and encryption. The transmitter features durable metal construction, AA or SB900A recharge

able power (with dockable charging), and TA4 or LEMO3 connector options.

Shure Incorporated

2/24

Features

Performance

•20 Hz to 20 kHz range with flat frequency response

•Automatic input staging optimizes gain setting

•AES 256-bit encryption-enabled for secure transmission

•>120 dB dynamic range

•100 meter (300 feet) line-of-sight operating range

•Selectable modulation modes optimize performance for spectral efficiency

◦ Standard – optimal coverage, low latency

◦ High density – dramatic increase in max system channel count

•Built-in tone generator and RF markers to facilitate walk-testing

•Switchable Power Levels = 2/10/35 mW (region dependent)

•Frequency Diversity selection using two bodypacks

Design

•TA4 or LEMO3 audio connector option

•Backlit LCD with easy to navigate menu and controls

•Rugged metal construction

•Flexible ¼ wave antenna

•Menu and power lockout

Power

•Over 8 hours continuous use with 2 x AA alkaline batteries

•Shure SB900A lithium-ion rechargeable battery provides extended battery life, precision metering, and zero

memory effect

•External charging contacts for docked charging

Included Components

AA alkaline batteries (2) 80B8201

¼ wave antenna Varies by Region

Threaded TAF4 adapter WA340

Zipper bag 26A13

Belt clip 44A12547

Optional Accessories

Bodypack rechargeable lithium-ion battery SB900A

Shure Incorporated

3/24

Y-Cable for bodypack transmitters AXT652

LEMO Y-cable for bodypack transmitters AXT652LEMO3

Instrument cable WA302

Replacement belt clip 44A12547

Instrument cable with right angle 1/4" connector WA304

Mute Switch for Bodypack WA661

Mute Switch for 2 Bodypacks WA662

AD1 Transmitter Overview

①RF Antenna

For RF signal transmission.

②Display

View menu screens and settings. Press any control button to activate the backlight.

③Infrared (IR) Port

Align with the receiver IR port during an IR Sync for automated transmitter tuning and setup.

④Control Buttons

Use to navigate through parameter menus and to change settings.

⑤Battery Compartment

Requires two AA batteries or Shure SB900A rechargeable battery.

⑥AA Battery Adapter

Use to secure AA batteries. Remove when using a Shure SB900A battery.

⑦SMA Connector

Connection point for RF antenna.

⑧Power Switch

Powers the unit on or off.

⑨Power LED

•Green = unit is powered on

•Red = low battery, Mute Mode enabled, input overload, or battery error (see Troubleshooting)

Shure Incorporated

4/24

⑩Input Jack

Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.

Note: A LEMO connector model variation of this transmitter is available.

Transmitter Controls

Use the controls to navigate through parameter menus and change values.

exit Acts as a 'back' button to return to previous menus or parameters without confirming a value

change

enter Enters menu screens and confirms parameter changes

∨∧ Use to scroll through menu screens and to change parameter values

Tip: Use the following control shortcuts for quick set up:

•Hold the ∧button while powering-on to lock or unlock the transmitter controls

•Hold the exit button while powering-on to set the transmitter RF output to mute

Shure Incorporated

5/24

Locking the Interface

Lock transmitter interface controls to prevent accidental or unauthorized changes to parameters. The lock icon ap

pears on the home screen when the interface lock is enabled.

1. From the Utilities menu, navigate to Locks and select one of the following lock options:

◦None: The controls are unlocked

◦Power: The power switch is locked

◦Menu: The menu parameters are locked

◦All: The power switch and menu parameters are locked

2. Press enter to save.

Tip: To quickly unlock a transmitter: Press enter twice, select None, and press enter.

Home Screen Display

The home screen shows transmitter information and status.

Tip: There are four options to choose the information shown on the home screen. Use the arrow buttons to select

one of the following choices:

•Name

•Frequency Setting

•Group (G) and Channel (C)

•Device ID

The following icons appear to indicate transmitter settings:

Battery runtime in hours and minutes or bar display

Key: Displayed when encryption is enabled

Lock: Displayed when controls are locked. Icon will

flash if access is attempted to a locked control (power

or menu).

STD: Standard Transmission Mode

HD: High Density Transmission Mode

Shure Incorporated

6/24

Box: When the box has an "x", Mute Mode is on and

engaged. If the box is empty, Mute Mode is on, but not

engaged.

Battery Installation

①Accessing the Battery

Compartment

Press the side tabs on the bodypack and open the battery door as shown to ac

cess the battery compartment.

②Installing Batteries •AA Batteries: Place batteries (note polarity markings) and AA Adaptor as

shown and close the door

•Shure SB900A Battery: Place battery as shown (note polarity markings). Re

move the AA adapter and set it aside. Close the door to secure the battery.

Note: If using AA batteries, set the battery type using the transmitter menu.

Setting the AA Battery Type

To ensure accurate display of transmitter runtime, set the battery type in the transmitter menu to match the in

stalled AA battery type.

Note: If a Shure SB900A rechargeable battery is installed, selecting a battery type is not necessary and the battery

type will display Shure.

1. Navigate to the Utilities and select Battery.

2. Use the ▼▲ buttons to select the installed battery type:

◦Alkaline = Alkaline

◦NiMH = Nickel Metal Hydride

◦Lithium = Lithium Primary

3. Press enter to save.

Shure Incorporated

7/24

AA Battery Installation

Fully insert the batteries as shown to ensure proper battery contact and to allow the door to latch securely.

Shure SB900A Rechargeable Battery

Shure SB900A lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly

charge to 50% capacity in one hour and reach full charge within three hours.

Single chargers and multiple bay chargers are available to recharge the Shure batteries.

Caution: Only charge Shure rechargeable batteries with a Shure battery charger.

Shure SB900A Runtime

2 mW 10 mW 35 mW

Up to 9 hours Up to 9 hours Up to 5 hours

Checking Battery Info

When using a Shure rechargeable battery, the receiver and transmitter home screens display the number of hours

and minutes remaining.

Detailed information for the battery is displayed Battery menu of the transmitter: Utilities > Battery

•Battery: The chemistry type of for the installed battery (Shure, Alkaline, Lithium, NiMH)

•Bars: Indicates the number of bars displayed

•Time: Battery runtime

•Charge: Percentage of charge capacity

•Health: Percentage of current battery health

•Cycle Count: Total of the number of charging cycles for the installed battery

•Temperature: Battery temperature reported in Celsius and Fahrenheit

Shure Incorporated

8/24

Important Tips for Care and Storage of Shure Rechargeable Batteries

Proper care and storage of Shure batteries results in reliable performance and ensures a long lifetime.

•Always store batteries and transmitters at room temperature

•Ideally, batteries should be charged to approximately 40% of capacity for long-term storage

•Periodically clean the battery contacts with alcohol to maintain ideal contact

•During storage, check batteries every 6 months and recharge to 40% of capacity as needed

For additional rechargeable battery information, visit www.shure.com.

AA Batteries and Transmitter Runtime

Transmitters are compatible with the following AA battery types:

•Alkaline

•Nickel Metal Hydride (NiMH)

•Lithium Primary

A 5-segment battery indicator representing the charge level of the transmitter battery is displayed on the screens

of the transmitter and receiver. The following tables contain the approximate remaining transmitter runtime in

hours:minutes.

Note: Battery runtimes vary by manufacturer, battery age, and environmental conditions.

AA Batteries and Transmitter Runtime

Alkaline

Battery Indicator

Approximate Run

time Remaining

(hours:minutes)

8:00 - 6:00

> 4:00

> 1:45

≦1:45

≦0:45

Shure Incorporated

9/24

Battery Indicator

Approximate Run

time Remaining

(hours:minutes)

≦0:15

NiMH (2700 mAh)

Battery Indicator

Approximate Runtime Remaining

(hours:minutes)

11:00 - 8:00

> 5:00

> 2:00

≦2:00

≦0:45

≦0:15

Lithium Primary (3500 mAh)

Battery Indicator

Approximate Runtime Remaining

(hours:minutes)

14:00 - 10:00

> 6:00

> 2:00

≦2:00

≦0:45

≦0:15

Menu Parameters

The Main menu organizes the available transmitter parameters into three sub-menus:

•Radio

•Audio

•Utilities

Shure Incorporated

10/24

Tip: Use the arrow buttons to scroll between the sub-menus.

Tips for Editing Menu Parameters

•To access the menu options from the home screen, press the enter button. Use the arrow buttons to access ad

ditional menus and parameters.

•A menu parameter will blink when editing is enabled

•To increase, decrease or change a parameter, use the arrow buttons

•To save a menu change, press enter

•To exit a menu without saving a change, press exit

Menu Map

Menu Parameter Descriptions

Radio Menu

Freq

Press the enter button to enable editing of a group (G:) channel (C:) or frequency (MHz). Use the arrow buttons to

adjust the values. To edit the frequency, press the enter button once to edit the first 3 digits, or twice to edit the

second 3 digits.

Power

Higher RF power settings can extend the range of the transmitter.

Note: Higher RF power settings decrease battery runtime.

Output

Andere Handbücher für AD1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Shure Sender Handbücher

Shure

Shure P4T Bedienungsanleitung

Shure

Shure UC2 Bedienungsanleitung

Shure

Shure Axient Bedienungsanleitung

Shure

Shure AXIENT AXT100 Bedienungsanleitung

Shure

Shure AD3 Bedienungsanleitung

Shure

Shure T1 Bedienungsanleitung

Shure

Shure AD3 Bedienungsanleitung

Shure

Shure AD3 Bedienungsanleitung

Shure

Shure ADX1-G56 Bedienungsanleitung

Shure

Shure Axient Digital ADX1 Bedienungsanleitung

Shure

Shure ADX2 Bedienungsanleitung

Shure

Shure T2 Bedienungsanleitung

Shure

Shure Axient Digital ADX1 Bedienungsanleitung

Shure

Shure W10BT Bedienungsanleitung

Shure

Shure AXT200 Bedienungsanleitung

Shure

Shure P4T Bedienungsanleitung

Shure

Shure ADX2 Bedienungsanleitung

Shure

Shure U1 Bedienungsanleitung

Shure

Shure ULXD6 Bedienungsanleitung

Shure

Shure ULXD6 Bedienungsanleitung

Shure

Shure P4T Bedienungsanleitung

Shure

Shure UC1L Bedienungsanleitung

Shure

Shure P4T Bedienungsanleitung

Shure

Shure AXIENT AXT100 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung