Shuttle HOT-579 Bedienungsanleitung

HOT-579

Pentium™processor

Based PCIMAINBOARD

User's Manual

NOTICE

AllRightReserved

Manual Ver 1.1

Allinformation, documentation, andspecifications contained inthis manual aresubject to changewithout prior

notificationbythemanufacturer.

The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a

commitment to update the information contained herein.

TRADEMARKS

All the brands and product names referred to in this manual are trademarks or registered trademarks of their respective

holders.

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accordance

with the manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help and for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful "How to Identify and

Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office. Washington,

DC 20402, Stock 004-000-00345-4

FCCWarning

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the users authority

to operate this equipment.

Note: In order for an installation of this product to maintain compliancewith the limits for a Class B device, shielded cables

and power cord must be used.

CE Notice:

Following standards were applied to this product, in order to achieve compliance with the electromagnetic compatibility :

- Immunity in accordance with EN 50082-1: 1992

- Emissions in accordance with EN 55022: 1987 Class B.

PREFACE ........................................................................................................................3

CHAPTER 1 FEATURES ......................................................................................................4

Accessories of HOT-579 .......................................................................................................................... 6

CHAPTER 2HARDWARE CONFIGURATION.............................................................................7

Jumper Setting........................................................................................................................................... 7

CPUClock Configurations - JP4 ~ JP6 and JP11 ~ JP14........................................................................ 8

SystemClock and CPUMultiplier onHOT-579 ..................................................................................... 9

CPUVoltage Configuration -JP33 ........................................................................................................ 10

Flash EEPROM Vpp - JP17................................................................................................................... 11

ClearCMOS -JP19................................................................................................................................. 11

PowerSupply Type Select - JP31........................................................................................................... 11

Connectors& Sockets............................................................................................................................. 12

CHAPTER 3MEMORY CONFIGURATION ..............................................................................14

CHAPTER 4 FLASH UTILITY .............................................................................................16

CHAPTER 5 BIOS SETUP ...............................................................................................18

MainMenu .............................................................................................................................................. 19

StandardCMOS Setup............................................................................................................................ 21

BIOS Features Setup............................................................................................................................... 23

Chipset Features Setup............................................................................................................................ 25

PowerManagement Setup ...................................................................................................................... 27

PCIConfiguration Setup......................................................................................................................... 29

Integrated Peripherals ............................................................................................................................. 31

PasswordSetting ..................................................................................................................................... 33

TABLE OF CONTENTS

HOT-579mainboardis a highlyintegratedIBM PC/AT compatible systemboard. The

designwill accept AMD K5, K6, Intel Pentium P54C, Pentium MMX, IDT-C6 and Cyrix/

IBM6x86, 6x86L, 6x86MX processors and also featureshigh-performance pipelinedburst

secondarycache memory support with size of 1024KB or 512KB. The memory subsystem

isdesigned to support up to 512 MB of EDO RAM, Standard FastPage DRAM and SDRAM

instandard 72-pin SIMM socket and 168-pin 3.3V DIMMsocket.

HOT-579provides a new level of I/O integration. VIA580VPX chipset provides increased

integrationandimprovedperformance over other chipsetdesigns.

TheVIA580VPX chipsetprovides anintegrated BusMastering IDEcontroller withtwo high

performanceUltra 33DMA IDE interfaces for up to four IDE devices.

TheonboardI/Ocontrollerprovides the standard PCI/Ofunctions:floppyinterface, two

FIFOserial ports,an IrDAdevice portand aSPP/EPP/ECP capableparallel port.

Upto fourPCI localbus slots provide a high bandwidth data path for data-movement

intensivefunctions suchas graphics,and up to three ISA slots complete the I/O function.

TheHOT-579 providesthe foundation for cost effective, high performance, highly expand-

ableplatforms, which deliverthelatest in Pentiumprocessor and I/Ostandard.

PREFACE

FEATURES

TheHOT-579 Mainboard is carefullydesigned for thedemanding PC userwhowants high performance

andmanyintelligentfeatures in a compactpackage:

Chipset:

FeaturesVIA580VPXChipset with I/Osubsystems.

CPUSupport:

AMD K6 166~266 MHz, K5 PR75~PR166,

IntelPentium 75~200MHz, Pentium MMX 166~233 MHz,

Cyrix/IBM6x86 P120+~P166+,6x86L P166+,6x86MX PR166~PR266,

IDT-C6150~200MHz.

SecondaryCache:

Onboard1024KB or512KB PipelinedBurst Cache.

VersatileMemorySupports:

Equippedwith fourSIMM sockets to support (4, 8,16, 32, 64 and128MB) 72-pin EDO or

FPmemory modulesand twoDIMM sockets to (8, 16, 32, 64 or 128MB) 168-pin

SDRAMmemory modulesup to256 MB.

PCIandISA ExpansionSlots:

Providesfour 32-bit PCI slotsand three 16-bit ISAslots.

OnboardI/OChip:

Providesone Floppyport; oneoptional PS/2mouse connector; twohigh-speed UART

compatibleserial ports andone parallel portwith ECP andEPP capabilities. Serial Port 2

canalso bedirected fromCOM2 tothe InfraredModule forwireless connections.

OnboardPCI Bus MasterIDE Controller:

TwoUltra DMA/33 Bus Master IDEPorts supportsfour IDE devices up to33 MB/sec

IDEtransfers and supports Enhanced PIO Modes 3 and 4and BusMaster IDE DMA

Mode 2 devices.

Onboard12-pin AT and20-pin ATXPower Supply:

ProvidesAT and ATXpower connector onboard.

ATXpower supports soft-on/off function.

SystemBIOS:

ProvideslicensedAwardV4.51PG BIOS on FlashEEPROM.

SupportsGreenPC, DMI andBundledwith Symbios Login(NCR) SDCMV4.0 SCSI

BIOS.

ACPI:

SupportACPI(AdvancedConfigurationandPowerInterface) function. ACPI provide

moreEnergy SavingFeatures for the future operating system supporting OS Direct

PowerManagement (OSPM) functionality.

BoardSize:

3/4baby AT compact size 220mm x 235mm.

ACCESSORIESOF HOT-579

Jumper Setting

Jumperpin headers show on right side are

usedtoconfigure system clock,CPU

multiplierandCPU voltages.

SystemClock- JP11,JP12 andJP13

JP11,JP12 andJP13 are3-pins header

jumperwhich isused toadjust System

Clock from 50MHz to 83 MHz.

CPUMultiplier -JP4, JP5and JP6

JP4,JP5 and JP6 are2-pins header jumper

hichis used to adjust CPU core multiplier

from 1.5X to 5.5X.

CPUVoltages-JP33

JP33is used to adjust onboard voltages output from Switching type regulatorsto CPU by

insertingor removing mini jumper from pin headers.

Thosehardware settings are made through the useof jumpercaps to connect jumper pins on

the main board. The jumpers will be show graphically such as to connect pins 3&4 and

5&6, and to connect pins 1&2 and 3&4 for six pin jumpers.

Jumpers will be show graphically such as to connect pins 2&4 and to connect

pins3&4 for four pin jumpers.

Jumpers with two pins will be shown as for Short (On) and for Open (Off).

Toconnect the pins, simply place a plasticjumper cap over the two pins as diagramed.

HARDWARECONFIGURATION

CPU Clock Configuration - JP4 ~ JP6 and JP11 ~ JP13

ProcessorSpeedSystem

Clock MultiplierVcore/Vio

IntelPentium

P55CMMX

233 MHz66 MHz3.5x2.8V/3.3V

200 MHz66 MHz3x2.8V/3.3V

166 MHz66 MHz2.5x2.8V/3.3V

IntelPentium

P54C

200 MHz66 MHz3x3.3V

166 MHz66 MHz2.5x3.3V

150 MHz60 MHz2.5x3.3V

133 MHz66 MHz2x3.3V

120 MHz60 MHz2x3.3V

100 MHz66 MHz1.5x3.3V

90 MHz60 MHz1.5x3.3V

75 MHz50 MHz1.5x3.3V

AMD-K6

266 MHz66 MHz4x2.2V/3.3V

233 MHz66 MHz3.5x3.2V/3.3V

(2.2V/3.3V)

200 MHz66 MHz3x2.9V/3.3V

166 MHz66 MHz2.5x2.9V/3.3V

AMD-K5

PR166 66 MHz1.75 x3.52V

PR133 66 MHz1.5x3.52V

PR120 60 MHz1.5x3.52V

PR100 66 MHz1.5x3.52V

PR90 60 MHz1.5x3.52V

PR75 50 MHz1.5x3.52V

Cyrix/IBM

6x86MX

PR266 66 MHz3.5x2.9V/3.3V

PR233 66 MHz3x2.9V/3.3V

PR200 66 MHz2.5x2.9V/3.3V

PR166 60 MHz2.5x2.9V/3.3V

Cyrix/IBM

6x86L P166+66 MHz2x2.8V/3.3V

P150+60 MHz2x2.8V/3.3V

Cyrix/IBM

6x86

P166+66 MHz2x3.52V

P150+60 MHz2x3.52V

P133+55 MHz2x3.52V

P120+50 MHz2x3.52V

IDT-C6

150MHz60 MHz2.5x3.52V

180MHz60 MHz3x3.52V

200MHz66 MHz3x3.52V

Table 2-1

SystemClock and CPUMultiplier on HOT-579

Forwhom like to set up system manually, listed tables show all theSystem Clock and CPU

Multiplierthat HOT-579 can offer.

Table2-2 showsthe System Clock from 50 MHz to 83 MHz.

Table2-3 showsCPU Multiplier from 1.5X to 5.5X.

Note:Since PCI clockis halfof systemclock, 75MHzand 83MHzsystemclocks may

causePCIclockbeyond PCIspecification.

System

Clock

JP11

JP12

JP13 PCIClock

50 MHzJP11:2-3On

JP12:2-3On

JP13:2-3On25 MHz

55 MHzJP11:2-3On

JP12:1-2On

JP13:2-3On27.5MHz

60 MHzJP11:1-2On

JP12:2-3On

JP13:2-3On30 MHz

66 MHzJP11:2-3On

JP12:2-3On

JP13:1-2On33 MHz

75 MHzJP11:1-2On

JP12:1-2On

JP13:2-3On37.5MHz

83 MHzJP11:2-3On

JP12:1-2On

JP13:1-2On41.5MHz

MultiplierJP4

JP5

JP6MultiplierJP4

JP5

JP6

1.5 x JP4:Off

JP5:Off

JP6:Off 4 x JP4:On

JP5:Off

JP6:On

2 x JP4:Off

JP5:Off

JP6:On4.5 x JP4:On

JP5:On

JP6:On

2.5 x JP4:Off

JP5:On

JP6:On5 x JP4:On

JP5:On

JP6:Off

3 x JP4:Off

JP5:On

JP6:Off 5.5 x JP4:On

JP5:Off

JP6:Off

3.5 x JP4:Off

JP5:Off

JP6:Off

Table 2-2

Table 2-3

Inhaltsverzeichnis

Andere Shuttle Hauptplatine Handbücher

Shuttle

Shuttle AV18 Bedienungsanleitung

Shuttle

Shuttle MK32N Bedienungsanleitung

Shuttle

Shuttle HOT-591P Bedienungsanleitung

Shuttle

Shuttle Spacewalker MV11 Bedienungsanleitung

Shuttle

Shuttle FB65 Bedienungsanleitung

Shuttle

Shuttle FB62 Bedienungsanleitung

Shuttle

Shuttle AB49 Bedienungsanleitung

Shuttle

Shuttle FT61 Bedienungsanleitung

Shuttle

Shuttle HOT-617 Bedienungsanleitung

Shuttle

Shuttle MB11 Bedienungsanleitung

Shuttle

Shuttle MB48 Bedienungsanleitung

Shuttle

Shuttle HOT-675 Bedienungsanleitung

Shuttle

Shuttle AK10 Bedienungsanleitung

Shuttle

Shuttle AK12 Bedienungsanleitung

Shuttle

Shuttle MV43P Bedienungsanleitung

Shuttle

Shuttle Spacewalker AE14 Bedienungsanleitung

Shuttle

Shuttle MV43 Bedienungsanleitung

Shuttle

Shuttle AK35GT Bedienungsanleitung

Shuttle

Shuttle HOT-603 Bedienungsanleitung

Shuttle

Shuttle AB52P Bedienungsanleitung

Shuttle

Shuttle MV21 Bedienungsanleitung

Shuttle

Shuttle FN85 Bedienungsanleitung

Shuttle

Shuttle FN25 Bedienungsanleitung

Shuttle

Shuttle Spacewalker AV45GT Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung