Siemens AR6111-MX Bedienungsanleitung

Fire & Security Products

Siemens Building Technologies

Card reader AR6111-MX

Installation

Clock/Data Interface Omron and Wiegand

Siemens Building Technologies AR6111-MX-Manual.doc

Fire & Security Products 02.2003

Safety regulations and warnings

lThe unit must only be used for the purpose intended by the manufacturer.

lThe installation instructions must be kept to hand and made available to every

user.

lUnauthorized changes and the use of spare parts and accessories which are not

sold or recommended by the manufacturer of the unit could cause fire, electric

shock or injury. Therefore, such measures will result in a renunciation of liability

and the manufacturer will not accept any guarantee claims.

lThe manufacturer's guarantee terms in the version valid at the time of the sale

are applicable to the unit. No liability will be accepted for unsuitably or incorrectly

set parameters – whether automatic or manual – or for inappropriate use of the

unit.

lAll repairs must be carried out by the manufacturer.

lThe user is responsible for ensuring that the unit is set up and connected in ac-

cordance with the recognized technical regulations in the country of installation

and any other guidelines valid in the relevant region.

lBefore opening the unit, always switch off the power supply and take measure-

ments to ensure that there is no power to the unit.

lIf an operating display goes out, this does not necessarily mean that the unit is

disconnected from the mains and has no power. If you are working on an open

device, remember that live components may be exposed.

Introduction

Thank you for deciding to purchase the AR6111-MX. The ID card reader

AR6111-MX in a wall switch housing is part of the new Access reader range.

The reader reads proximity ID cards of 13.56 MHz technologies:

ISO14443 Type A - like Mifare® 1k, 4k or UltraLight, my-D proximity (SLE55Rxx),

ISO14443 Type B - like my-C (SLE66CL160S) and

ISO15693 - like my-D vicinity, I-Code SLI, TagIT-HFI.

The card number will be transmitted to the Access control system for processing.

Siemens Building Technologies AR6111-MX-Manual.doc

Fire & Security Products 02.2003

Approval

If used according to the instructions, this radio system meets the basic require-

ments of article 3 and the remaining applicable conditions of the R&TTE directive

(1999/5/EG) of March 1999.

Equipment Classification according to ETSI EN 300 330: Class 2

FCC ID: S4OAR6111-MX

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Siemens Building Technologies AR6111-MX-Manual.doc

Fire & Security Products 02.2003

Technical specifications

Housing plastic (potted electronic)

Color gray (like RAL 7004)

Degree of protection IP 65

Power supply 9 - 15 V DC

Power consumption max. 2,6 W

Temperature range -25 °C to +60 °C

Relative air humidity 95% (no dew formation)

Antenna internal

Operating frequency 13,56 MHz

transmitter power 200 mW ±2 dB

Qualified Transponders

(read serial number) ISO14443A:

Mifare Standard 1k and 4k (UID, S/B, MAD),

Mifare UltraLight (UID, B), Mifare DESfire

(UID), my-D proximity (UID, B)

ISO14443B:

my-C (SLE66CL160S) (UID)

ISO15683:

my-D vicinity, I-Code SLI, TagIT HFI,

STM LRI512 (all UID)

connecting cable 50 cm (LiYY 12 * 0,2 mm2)

Transducer 1 x LED red

1 x LED green

1 x beeper

Digital Inputs 4 (maximum cable length 3 m)

Interfaces: Clock / Data

- Magnetic stripe format

- Wiegand

RS232-TTL (for service only)

Siemens Building Technologies AR6111-MX-Manual.doc

Fire & Security Products 02.2003

Installation

The reader is designed to be wall-mounted on or without flush-mounting boxes.

Notes:

lThe reader should not be mounted directly onto conductive materials, such as metal surfaces, metal

frames (reinforcement) or metal-plated surfaces, as these surfaces will reduce the reader's range.

The clearance to such surfaces should be at least 30 cm.

lThe distance between readers of the same design should not be less than 30 cm.

lBefore final installation, the planned installation site should be checked for suitability.

83,5

7,7

3,5

4,2

Siemens Building Technologies AR6111-MX-Manual.doc

Fire & Security Products 02.2003

Connecting the reader

Color Function Description

red Vcc (9 - 15 V DC)

black Ground* power supply

green Data-/Clock (Data / Data0)

white Data-/Clock (Clock / Data1)

violet Data-/Clock (CLS / Card Present) Data-/Clock Interface

grey LED green

brown LED red

yellow Beeper

blue Hold

digital inputs **

orange RS232-TTL (Rx)

white / black RS232-TTL (Tx) Service -Interface

white / brown - N.C. -

Notes:

*) If an external power supply is used the ground signal from the power supply and the host

must be connected.

**) The digital inputs can only be connected to Ground. Any connection to external voltage

might damage the unit!

Siemens Building Technologies AR6111-MX-Manual.doc

Fire & Security Products 02.2003

Function and Functional Testing

Digital Inputs:

LED green: Activates the green LED while the input is switched to ground

LED red: Activates the red LED while the input is switched to ground

Beeper: Activates the beeper while the input is switched to ground

Hold: While input "Hold" is switched to ground the reader doesn't accept

any Transponder

Configuration Mode:

After the power supply is switched on the reader starts his configuration mode for 8

seconds. The configuration mode is indicated by alternating blinking of the red and

green LED.

While the configuration mode is active the reader could be configured with a spe-

cial ConfigCard. In this mode the reader accepts only ConfigCards. Please contact

your supplier to get further information's about ConfigCards.

After the configuration modes has finished the reader changed into the normal op-

eration mode.

Normal Operation Mode

In the normal operation mode the LED and the beeper are controlled by the digital

inputs.

When the reader detects a transponder the data where send out at the clock/data

interface and the beeper indicates the detection with a short single beep nonrecur-

ring.

To repeat this a read action the transponder must leave the detection range of the

reader for more than 1,5 seconds.

If the Transponder data length doesn't match to the reader configuration the

beeper indicates an error by a short double beep. In the case no data's are send

out at the clock/data interface.

Issued by

Siemens Building Technologies

Fire & Security Products GmbH & Co. oHG

D-76181 Karlsruhe

www.sbt.siemens.com

Siemens Building Technologies AG

Data and design subject to change without notice.

Supply subject to availability.

Printed in the Federal Republic of Germany

on environment-friendly chlorine-free paper.

Dokument Nr.

Isue 05.2004

We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights

and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our

prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

Inhaltsverzeichnis

Andere Siemens Kartenleser Handbücher

Siemens

Siemens SIMATIC RF300 Benutzerhandbuch

Siemens

Siemens PR500-Cotag Bedienungsanleitung

Siemens

Siemens PM500-Cotag Bedienungsanleitung

Siemens

Siemens AR10S-MF Installationsanleitung

Siemens

Siemens AR50M-MF Bedienungsanleitung

Siemens

Siemens SIMATIC RF650M Bedienungsanleitung

Siemens

Siemens RB500 Bedienungsanleitung

Siemens

Siemens SIMATIC RF1070R Bedienungsanleitung

Siemens

Siemens 6FL7171-8AD Bedienungsanleitung

Siemens

Siemens SIMATIC RF310M Bedienungsanleitung

Siemens

Siemens AR6181-MS Bedienungsanleitung

Siemens

Siemens AR4 S-MF Series Installationsanleitung

Siemens

Siemens SIMATIC MV440 Bedienungsanleitung

Siemens

Siemens SC7 Installations- und Betriebshandbuch

Siemens

Siemens Bewator PR500 Installations- und Betriebshandbuch

Siemens

Siemens AR6181-MX Bedienungs- und Wartungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch