Siemens SC7 Installations- und Betriebshandbuch

SC7 / SC7P / UK – 06.14

SC7 Smart Card Reader

Installation Note

General

SC7 SC7P

The SC7 is a Smart Card Reader that only reads data from the Chip Serial Number

in Mifare®cards. It provides as default a 32Bit Wiegand output. The Reader is available

in 2 variants – the SC7 Smart Card only Reader and SC7P Smart Card and keypad

Reader.

Installation

Mounting

The SC7 Smart Card Reader can be connected to a Granta 4422 Reader Module,

Entro DC-12 or DC-22 Door Controllers or an Entro Lite DC800 Door Controller. The SC7

is prepared with a fixed 3m cable mounting.

Remove the cover by pushing in the lug on its lower edge using a suitable

screwdriver. Choose a suitable position to mount the Reader near the door. The SC7

Reader has a typical range of 2cm so it must be mounted in a position where the Smart

Card can easily be brought within this distance. We recommend it is mounted

approximately 1m (3.5ft) above the ground. Also consider ease of access to the door once

the Smart Card has been read, for example, it is better to mount the Reader near the

opening side of the door rather than the hinge side.

The Reader should be mounted with the LED at the top. Mark out and drill the two

mounting holes over the hole for the cable (a drawing is provided on the last page in this

document – Note: not to scale.) If this hole does not exist make sure to prepare for this as

well, do not cut the cable less than 10cm (4in).

Do not fix the Reader to the wall yet. The holes accept 4mm machine screws or No

8 wood screws (provided with the Reader).

Connect the Reader according the wiring diagram on the following pages,

depending of which system the Reader is connected to.

SC7 / SC7P / UK – 06.14

Connection to a Granta 4422 Reader Module

Configuration

See also the installation note for the Granta 4422 Reader Module in order to make necessary

settings

of the jumpers (Wiegand, +12V and active-low strobe signal). Use interface number 309 for definition of

Access Points in Granta SW.

Connection to Entro DC-12 and DC-22 Door Controllers

Configuration

The interface used is Wiegand. Ensure that the power jumper is set to VIN.

SC7 / SC7P / UK – 06.14

Connection to an Entro Lite DC800 Door Controller

Configuration

Following jumper selections must be done:

•

Reader type (J4) must be put on the Wiegand

•

Voltage jumper (J1) to VIN

•

Function jumper (J3) to Entro Lite

•

(Note - if the DC800 is used in Entro - set J3 to Entro)

Operation

When the Reader is powered the LED is flashing for 5 seconds. After these 5

seconds the LED flashes by the sequence red, yellow and green before the LED is

switched off and the Reader is ready for use.

When a Smart Card is provided within the reading sector of the SC7 and the card is

accepted, the yellow LED is lit for approximately 0.5 seconds at same time as a message

is sent out. The yellow LED is only lit when a message is sent out from the Reader. After

this the Reader goes back to wait state, code from the same card is not sent again before

a time of 3 seconds has been elapsed provided the card has been out of the reading

sector.

Technical Specifications

Power Supply: 24V (+10 / +30 V)

Current consumption: 100mA max

Interfaces: Wiegand

Clock and Data

Housing: Plastic

Dimensions: SC7: 110 x 43 x 24

(H x W x D)mm: SC7P:138 x 43 x 24

Temperature: -40 to 55°C

Storage temperature: -40 to 55°C

IP Rating: SC7:IP67

SC7P:IP47

Connection: 3m cable

Led: Tricolor

Buzzer: Yes

Carrier frequency: 13.56 MHz

Hole Pattern

Drawing

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Kartenleser Handbücher

Siemens

Siemens AR10S-MF Installationsanleitung

Siemens

Siemens AR50M-MF Bedienungsanleitung

Siemens

Siemens SIMATIC RF1070R Bedienungsanleitung

Siemens

Siemens AR6181-MX Bedienungs- und Wartungsanleitung

Siemens

Siemens AR4 S-MF Series Installationsanleitung

Siemens

Siemens Bewator PR500 Installations- und Betriebshandbuch

Siemens

Siemens SIMATIC RF650M Bedienungsanleitung

Siemens

Siemens RB500 Bedienungsanleitung

Siemens

Siemens SIMATIC RF310M Bedienungsanleitung

Siemens

Siemens PM500-Cotag Bedienungsanleitung

Siemens

Siemens SIMATIC MV440 Bedienungsanleitung

Siemens

Siemens AR6111-MX Bedienungsanleitung

Siemens

Siemens PR500-Cotag Bedienungsanleitung

Siemens

Siemens AR6181-MS Bedienungsanleitung

Siemens

Siemens SIMATIC RF300 Benutzerhandbuch

Siemens

Siemens 6FL7171-8AD Bedienungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch