Siemens CP 5623 Bedienungsanleitung

CP 5623/CP 5624

___________________

SIMATIC NET

PG/PC - PROFIBUS

CP 5623/CP 5624

Operating Instructions

09/2013

C79000

-G8976-C281-03

Preface

Description of the device

Software installation

Hardware installation

Configuration

Technical specifications

Approvals

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

Order number: C79000-G8976-C281

Ⓟ

09/2013 Technical data subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance a

re required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CP 5623/CP 5624

Operating Instructions, 09/2013, C79000-G8976-C281-03 3

Preface

What the consignment contains

The following components are supplied with the CP 5623 / CP 5624:

●Communications processor CP 5623 or communications processor CP 5624

●SIMATIC NET DVD including

–SIMATIC NET PC software

–Manual Collection

●Certificate of license

Please check that the consignment you have received is complete. If it is not complete,

please contact your supplier or your local Siemens office.

Validity of this documentation

These operating instructions are valid for the following products:

●CP 5623

order number: 6GK 1562-3AA00

●CP 5624

order number: 6GK1 562-4AA00

Content of this documentation

These operating instructions contain information about the installation and configuration of

the CP 5623 and CP 5624 communications processors.

Updated operating instructions on the Internet

You will find the current version of these operating instructions on the Product Support pages

under the following entry ID:

38549256 (http://support.automation.siemens.com/WW/view/en/38549256)

Further documentation

The documents listed below contain more detailed information on commissioning and using

the communications processor. You will find this documentation on the Product Support

pages on the Internet under the following entry link:

Support (http://support.automation.siemens.com/WW/view/en)

Enter the entry ID shown below of the relevant manual as the search item.

Preface

CP 5623/CP 5624

4Operating Instructions, 09/2013, C79000-G8976-C281-03

●

Configuration manual Commissioning PC Stations

This provides you with detailed information on commissioning and configuring SIMATIC

NET PC communications modules.

Entry ID:

13542666 (http://support.automation.siemens.com/WW/view/en/13542666)

●

System manual SIMATIC NET Industrial Communication with PG/PC

–

Volume 1– Basics

Entry ID:

42783968 (http://support.automation.siemens.com/WW/view/en/42783968)

–

Volume 2– Interfaces

Entry ID:

42783660 (http://support.automation.siemens.com/WW/view/en/42783660)

The system manuals introduce the topic of industrial communication and explain the

communications protocols used. There is also a description of the OPC interface as

user programming interface.

●

Installation manual SIMATIC NET PC Software

This document contains detailed information on installing the SIMATIC NET

PC software.

Entry ID:

42784913 (http://support.automation.siemens.com/WW/view/en/42784913)

●

System manual PROFIBUS Network Manual

In this document you will find detailed information about setting up a PROFIBUS network.

Entry ID:

35222591 (http://support.automation.siemens.com/WW/view/en/35222591)

SIMATIC NET documentation

You will find the entire SIMATIC NET documentation on the pages of Product Support:

10805878 (http://support.automation.siemens.com/WW/view/en/10805878)

Go to the required product group and make the following settings:

→Entry list →Entry type "Manuals / Operating Instructions"

Service & Support

In addition to the product documentation, the comprehensive online information platform of

Siemens Automation Customer Support supports at any time and at any location in the

world. You will find the Service & Support pages on the Internet at the following address:

(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=

en)

Apart from news, you will also find the following information there:

Preface

CP 5623/CP 5624

Operating Instructions, 09/2013, C79000-G8976-C281-03 5

●Product information, Product Support, Applications & Tools

●Technical Forum

●Technical Support - Ask the Siemens experts

●Our service offer:

–Technical Consulting, Engineering support

–Field Service

–Spare parts and repairs

–Maintenance, optimization, modernization and more

You will find contact data on the Internet at the following address:

(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)

See also

(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid=38

718979&caller=view)

SITRAIN - Siemens training for automation and industrial solutions

With over 300 different courses, SITRAIN covers the entire Siemens product and system

spectrum in the field of automation and drive technology. Apart from the classic range of

courses, we also offer training tailored for individual needs and a combination of different

teaching media and sequences, for example self-learning programs on CD-ROM or on the

Internet.

You will find detailed information on the training curriculum and how to contact our customer

consultants at the following Internet address:

(www.siemens.com/sitrain)

SIMATIC NET glossary

Explanations of the specialist terms used in this documentation can be found in the SIMATIC

NET glossary.

You will find the SIMATIC NET glossary here:

●SIMATIC NET Manual Collection

The DVD ships with certain SIMATIC NET products.

●On the Internet under the following entry ID:

50305045 (http://support.automation.siemens.com/WW/view/en/50305045)

Preface

CP 5623/CP 5624

6Operating Instructions, 09/2013, C79000-G8976-C281-03

CP 5623/CP 5624

Operating Instructions, 09/2013, C79000-G8976-C281-03 7

Table of contents

Preface ................................................................................................................................................... 3

1 Description of the device ......................................................................................................................... 9

1.1 Properties of the CP 5623..............................................................................................................9

1.2 Properties of the CP 5624............................................................................................................10

1.3 PROFIBUS interface....................................................................................................................11

1.4 Meaning of the LED display .........................................................................................................13

2 Software installation.............................................................................................................................. 15

2.1 Installing the SIMATIC NET PC software ....................................................................................15

2.2 Uninstalling the SIMATIC NET PC software................................................................................15

2.3 Alternative software packets ........................................................................................................16

3 Hardware installation............................................................................................................................. 17

3.1 Safety notices...............................................................................................................................17

3.2 Installing hardware.......................................................................................................................18

3.3 Hardware compatibility.................................................................................................................18

4 Configuration ........................................................................................................................................ 21

5 Technical specifications ........................................................................................................................ 23

A Approvals.............................................................................................................................................. 25

Index..................................................................................................................................................... 27

Table of contents

CP 5623/CP 5624

8Operating Instructions, 09/2013, C79000-G8976-C281-03

CP 5623/CP 5624

Operating Instructions, 09/2013, C79000-G8976-C281-03 9

Description of the device

1.1

Properties of the CP 5623

Properties

The CP 5623 is a communications processor for connecting PCs (personal computers) or

PGs (programming devices) to PROFIBUS and MPI networks. The essential properties are

as follows:

●Transmission speeds up to 12 Mbps.

●Floating RS-485 connector.

●Linking of up to 32 devices (PC, PG, SIMATIC S7 or ET 200) to form a network segment.

–By linking several segments with repeaters, up to 124 nodes can be connected.

●The additional interface signals for a direct link to a PLC (Programmable Logic Controller)

are supported up to 187.5 Kbps.

●Installation in PGs and PCs with a PCI Express slot. The following is supported:

–PCI Express x1

–Can also be operated in x4, x8 and x16 slots

–Plug and play

●Optimized for fast DP master operation (DP Base) with up to 124 DP slaves with full data

consistency.

●Relief of the PC/PG with event mechanisms.

–Automatic detection of data changes.

●Fast logic support regardless of the user program.

–Automatic linking of input and output data can be set by the user program.

●Measurement of own operating temperature with temperature sensor.

●Display of the total operating hours with operating hours counter.

Description of the device

1.2 Properties of the CP 5624

CP 5623/CP 5624

10 Operating Instructions, 09/2013, C79000-G8976-C281-03

Appearance

The following graphic shows the CP 5623 communications processor:

LEDs

PROFIBUS interface PB1 (master or slave)

1.2

Properties of the CP 5624

Properties

The CP 5624 is a communications processor for connecting PCs (personal computers) or

PGs (programming devices) to PROFIBUS and MPI networks. In addition to the properties of

the CP 5623, the CP 5624 also has the following features:

●Additional PROFIBUS connection as DP slave to a second DP network.

●DP master and DP slave can be operated at the same time.

●Program-controlled data transfer between master and slave module for setting up

hierarchical PROFIBUS networks.

Andere Handbücher für CP 5623

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Computerhardware Handbücher

Siemens

Siemens SIMATIC S7-400 CP 440 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5603 Bedienungsanleitung

Siemens

Siemens Simatic VS 710 Bedienungsanleitung

Siemens

Siemens SIMATIC CP 341 Bedienungsanleitung

Siemens

Siemens SINUMERIK 808D Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5614 A2 Bedienungsanleitung

Siemens

Siemens SIMOTION TB30 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 1411 Bedienungsanleitung

Siemens

Siemens SIMATIC S7-1200 CP 1243-8 IRC Bedienungsanleitung

Siemens

Siemens CP 5613 A3 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5603 Bedienungsanleitung

Siemens

Siemens Simatic S7-300 31xC Series Bedienungsanleitung

Siemens

Siemens Gigaset USB adapter 54 Bedienungsanleitung

Siemens

Siemens SPCN910 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 243-1 IT Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Gebrauchsanweisung

Siemens

Siemens CP 5613 A3 Bedienungsanleitung

Siemens

Siemens SMP16-CPU06 Series Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5622 Bedienungsanleitung

Siemens

Siemens SMN42 Bedienungsanleitung

Siemens

Siemens Fujitsu D1159 Bedienungsanleitung

Siemens

Siemens Metro 21 M216KASPC Bedienungsanleitung

Siemens

Siemens SIMATIC PCS 7 OSx Bedienungsanleitung

Siemens

Siemens CP 343-5 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung