Siemens SIMATIC PG 760 Handbuch

Product Information Bulletin

This leaflet gives you specific technical information

on your PG 760 programming device.

SIMATIC

PG 760 Programming Device

This product information bulletin contains notices which you should observe to ensure your own

personal safety, as well as to protect the product and connected equipment. These notices are

highlighted in the manual by a warning triangle and are marked as follows according to the level

of danger:

!Warning

indicates that death, severe personal injury or substantial property damage can result if proper

precautions are not taken.

!Caution

indicates that minor personal injury or property damage can result if proper precautions are not

taken.

Note

drawsyourattentiontoparticularlyimportantinformationontheproduct,handlingtheproduct,or

to a particular part of the documentation.

Please observe the following:

Note

Youcansetupandoperateyourprogrammingdeviceinconjunctionwiththefollowinginstructions.

You should only connect external devices and work with memory cards in conjunction with the

PG 760 manual.

Only qualified personnel should be allowed to install and work on this equipment using the

PG 760manual.Qualifiedpersonsare definedaspersonswhoareauthorizedtocommission,to

ground,andtotagequipment,systems,andcircuitsinaccordancewithestablishedsafetypractices

and standards.

!Warning

Thisdevicemayonlybeusedfortheapplicationsdescribedinthecatalogortechnicaldescription,

and only in connection with devices or components from other manufacturers which have been

approved or recommended by Siemens.

Thisproductcanonlyfunctioncorrectlyandsafelyifitistransported,storedandsetupcarefullyand

correctly, and operated and maintained as recommended.

SIMATICRand SINECRare registered trademarks of SIEMENS AG.

Thereproduction,transmissionoruseofthisdocumentoritscontentsis

not permitted without express written authority.

Offenderswillbeliablefordamages.Allrights,includingrightscreatedby

patent grant or registration of a utility model or design, are reserved.

We have checked the contents of this manual for agreement with the

hardwareandsoftwaredescribed.Sincedeviationscannotbeprecluded

entirely, we cannot guarantee full agreement. However, the data in this

manualarereviewedregularlyandanynecessarycorrectionsincludedin

subsequent editions. Suggestions for improvement are welcomed.

Technical data subject to change.

  

 E     

Siemens AG

AutomationGroup

ElektronikwerkKarlsruhe C79000ĆZ7076ĆC761

Prin ed in he Fed. Rep. of Germany

Siemens Ak iengesellschaf

Safety Guidelines

Correct Usage

Trademarks

PG 760 Product Information Bulletin

C79000-K7076-C761-03

Setting Up and Transporting the PG 760

Unpack your PG 760 programming device as follows:

1. Remove the packing.

2. Do no throw the original packing away. Keep it in case you have to

transport the unit again sometime in the future.

3. Check with the packing list to make sure no components are missing.

4. Check the packing and its contents for any shipping or transport damage.

5. Please inform your local dealer of any shipping or transport damages and

and of outstanding items indicated on the packing list.

!Caution

Risk of mechanical damage!

When transporting your PG 760 in cold weather when it may be exposed to

extreme variations in temperature, make sure that no moisture or

condensation can form on or in the unit.

The unit should be allowed to reach room temperature slowly before it is started

up. If condensation has formed, the unit should be left for about 12 hours before

being switched on.

Fill the serial number of your programming device in the table below. If your

device has been stolen and repair work is required the repair and maintenance

centers can only identify it by its serial number.

Serial number PG 760

Setting up the tower:

Proceed as follows:

1. Place your programming device on a horizontal and even surface.

Don’t cover the ventilating slots.

2. Place monitor and keyboard in the most convenient position.

3. Connect monitor and keyboard.

Despite the fact that the PG 760 is of rugged design, its internal components

are sensitive to severe vibrations or shock. You must therefore protect your

PG 760 against severe mechanical stressing when transporting it. Use the

original packing material if you have to ship the PG from one location to

another.

Unpacking the

PG 760

Setting up your

PG 760

Transport

2PG 760 Product Information Bulletin

C79000-K7076-C761-03

Hardware Components of the PG 760

You can access all important operator controls and displays from the front of

the unit.

All the power supply connectors and interface ports for hooking up to

external devices are located on the rear panel of the PG 760.

1LED displays

2CD-ROM drive

3 Free slot

4Diskette drive

5On/Off switch

6Memory Card port

7Protective cover for disk

drive

8Ventilating slots

Power LED

Hard disk access

Memory Card-port ac-

tive

MPI/DP port

Power

MPI/DP

Power supply

connector socket

(out)

Power supply

connector plug

(in)

Ventilator

Dummy plates cove-

ring expansion slots

VGA port

PS/2 mouse

COM2

port

COM1

port

MPI/DP port

LPT 1 port

PS/2 keyboard

Mains voltage

selector

Figure 1-1 Rear panel with connectors and ports and front panel of PG 760

Front

Rear Panel

(Connectors)

PG 760 Product Information Bulletin

C79000-K7076-C761-03

Ports and Connectors Function

Power supply connector Connection for power supply

PS/2 mouse Connection for PS/2 mouse

LPT 1 printer

Parallel interface Connection for parallel printer

MPI/DP Multipoint Interface (RS485)* Connection for S7 programmable

COM 1

V.24/MODEM/PLC

Serial port Connection for S5 programmable

controller

COM 2

V.24/mouse

Serial port

Connection for serial mouse

Connection for serial printer

VGA Interface Connection for external monitor

* Galvanic isolation within the safety extra-low voltage circuit (SELV)

The raised air outlet slots for ventilation are located at the front and back side

of your PG 760. These slots must not be covered in any way.

!Caution

Risk of overheating!

If you cover up the slots for the inlet and outlet air in any way, there is a risk

that your PG 760 or its power supply will be damaged.

Observe the following notes concerning the power supply of the unit.

Note

The power plug must be disconnected to isolate the unit completely from the

supply.

Note

For operation in Canada and the US a UL listed, CSA Labeled Cord Set must

be used. The unit is intended for operation with normal grounded power supply

networks (referred to as TN systems according to IEC 364-3).

The unit is not intended for operation with non-grounded or impedance-groun-

ded systems (IT systems). The Labeled Cord Set has to comply with the safety

requirements of the individual state.

Ventilating Slots

Power Supply

4PG 760 Product Information Bulletin

C79000-K7076-C761-03

If the set voltage does not correspond with your local voltage, you must

select the correct voltage by moving the mains voltage selector either to

115 V or 230 V.

!Caution

Risk of damage to the unit!

Operating the PG 760 with the incorrect mains voltage can damage the unit

since the input voltage is also applied to the mains outlet.

To operate the monitor, observe the manufacturer’s specifications.

Only a monitor with the following rated currents may be connected:

115 V 1 A max.

230 V 0.5 A max.

Select the correct voltages as follows:

1. For 120 V, using a normal screwdriver push the mains voltage selector to

the right. 115 V appears on the switch.

2. For 230 V, using a normal screwdriver push the mains voltage selector to

the left. 230 V appears on the switch.

Mains voltage selector

Power supply con-

nector socket (out)

Power supply

connector plug (in) Mains voltage

selector

230 Volt

115 Volt

Figure 1-2 Mains Voltage Selector

After having checked the right setting of the mains voltage selector and after

having connected all cables required for operation, you can switch on your

programming device. The ON/OFF switch is located behind the drive cover.

Selecting Mains

Voltage

Switching on

PG 760 Product Information Bulletin

C79000-K7076-C761-03

The programming device PG 760 is equipped with a floppy disk drive, a hard

disk drive and a CD-ROM drive as standard.

You can read, program and erase SIMATIC Memory Cards via the 68-pin

connector.

SIMATC Memory Cards

Point of orientation

Figure 1-3 SIMATIC Memory Cards Interface

Please note the following instructions while working with memory cards.

!Caution

Risk of damage to memory cards and to your programming device PG 760!

You must insert the memory card into a 68-pin connector with the type label

on top of it. The points of orientation on the memory card and on the slot

have to correspond with each other.

If you try to plug the memory card in the wrong way around, your

programming device or memory card will be damaged!

You must not take out the SIMATIC memory card as long as its LED is lit.

In order to program SIMATIC memory cards select ”PG 760 Hardware

Options” under Setup and set ”Programming interface” ”enabled”.

Drive Type

SIMATIC Memory

Cards

6PG 760 Product Information Bulletin

C79000-K7076-C761-03

You can store programs and data on diskettes with the disk drive and load

them from diskettes into the PG 760.

You can use the following diskettes:

Double-Sided High-Density Diskette Double-Sided Double-Density Diskette

3.5 in. 3.5 in.

1.44 Mbytes (135 TPI) 720 Kbytes

80 tracks per side 80 tracks per side

Programming device recognizes diskettes

by their coding Programming device recognizes diskettes

by their coding

The diskette is inserted in the disk drive as shown below:

Access LED

Ejector

!Caution

Risk of data loss!

You must not remove the diskette as long as the access LED is lit. Otherwise

you might lose the data on the diskette.

Do not remove the diskette until the access LED on the drive of the PG 760

has gone out.

You can use a number of different hard disk drives in your PG 760. The

memory capacity of the particular type of hard disk can be found in the

Technical Specifications. The hard disk drive is connected to the primary

IDE interface.

Whenever the hard disk drive is accessed, its access LED on the front of the

unit lights up.

!Caution

Risk of loss of data and damage to drive!

Drives are sensitive to vibrations and shock. Any vibrations occurring during

operation can lead to the loss of data or damage to the drive.

If you intend transporting the unit, switch it off, and wait until the drive has

come to rest (about 20 seconds) before you move it.

Diskette Drive

Types of Diskette

Handling Diskettes

Hard Disk Drive

Access LED

PG 760 Product Information Bulletin

C79000-K7076-C761-03

The CD-ROM drive enables you to easily update the already installed STEP 5,

STEP 7 software and Windows 95. The CD-ROM drive is connected to the

secondary IDE interface.

BUSY

123 4 5 6

This jack is used to connect a set of headphones. Please use headphones with a

stereo mini-jack plug.

This control is used to adjust the headphone volume. This control has no effect

on the left and right audio outputs from the LINE OUT connector on the back

of the unit.

This indicator lights while data is being read.

This door prevents dust from getting inside the CD-ROM reader and should re-

main closed. If your programming device is not switched on you can manually

push the tray and close the door of your CD-ROM drive.

Use a clip or any other device to remove the cartridge from the CD-ROM reader

if the electrical eject is disabled by software or if power failure occurs (See

”Emergency Eject” for details).

This button is pressed to open or close the CD tray when the power of your pro-

gramming device is on.

CD-ROM drive

Part Names and

Functions

1 Phones jack

2 Volume Control

3 BUSY Indicator

4 Door

5 Emergency

Eject Hole

6 Open/

Close Button

8PG 760 Product Information Bulletin

C79000-K7076-C761-03

The drive is configured as a Single. If you want to operate a second drive on this

bus, you have to set either one of them as Master and the other as Slave or vice

versa.

LINE

OUT

R GND L I/O BUS +5V GND +12V

DIGITAL

OUT

DIG GND

FACTORY USE ONLY

SINGLE JUMPER

BLOCK

123

789 1011 12 13

Connect a ground cable with a flat pin connector (as used in cars) to this ground

terminal.

This block of jumper locations sets the configuration for the CD-ROM reader.

(See figure ”Jumper Settings” for details).

Connect a cable to this output to transfer Digital Audio data to appropriate audio

devices.

Connect a cable to this output to transfer analog Audio data.

This block of jumper locations sets the configuration for the CD-ROM drive.

(See figure ”Jumper Settings” for details.)

Jumper Block A

1 Single

2 Factory use only

3 Factory use only

Jumper Block B

1 CSEL (for further extensions)

2 Slave

3 Master

123 123

Figure 1-4 Configuration

This BUS connector is used to connect a data/control line. Use a flat ribbon cable

to connect your CD-ROM drive to the IDE controller.

Connect the power supply cable to this connector.

Rear of the drive,

Configuration

7 Ground terminal

8 Jumper Block A

9 DIGITAL OUT

Connector

10 Line Out

Connector

11 Jumper Block B

12 I/O-Bus

Connector

13 Power

Connector

Andere Handbücher für SIMATIC PG 760

Inhaltsverzeichnis

Andere Siemens Computerhardware Handbücher

Siemens

Siemens CP 343-5 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5614 A2 Bedienungsanleitung

Siemens

Siemens Gigaset USB adapter 54 Bedienungsanleitung

Siemens

Siemens Metro 21 M216KA Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 243-1 IT Bedienungsanleitung

Siemens

Siemens CP 1626 Bedienungsanleitung

Siemens

Siemens SIMATIC PCS 7 OSx Bedienungsanleitung

Siemens

Siemens SIMATIC CP 340 Bedienungsanleitung

Siemens

Siemens SIMATIC S7-1200 CP 1243-8 IRC Bedienungsanleitung

Siemens

Siemens SED2 Series Bedienungsanleitung

Siemens

Siemens CPU 31 Series Gebrauchsanweisung

Siemens

Siemens CC-5 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5622 Bedienungsanleitung

Siemens

Siemens SINUMERIK 808D Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 1411 Bedienungsanleitung

Siemens

Siemens TC65 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 1623 Bedienungsanleitung

Siemens

Siemens Simatic 545-1106 Bedienungsanleitung

Siemens

Siemens CP 5623 Bedienungsanleitung

Siemens

Siemens CP 342-5 Bedienungsanleitung

Siemens

Siemens SPEEDSTREAM SS1021 Bedienungsanleitung

Siemens

Siemens LMV50 series Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Gebrauchsanweisung

Siemens

Siemens SIMATIC NET 6GK7 443-5FX02-0XE0 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung