Siemens SIMATIC S5 CPU Direct Driver Bedienungsanleitung
1
Siemens AG
SIMATIC S5 CPU
Direct Driver
1 System Configuration....................................................................................................... 3
2 Selection of External Device ............................................................................................ 7
3 Example of Communication Setting ................................................................................. 8
4 Setup Items ...................................................................................................................... 9
5 Cable Diagram ............................................................................................................... 14
6 Supported Device........................................................................................................... 16
7 Device Code and Address Code.................................................................................... 17
8 Error Messages.............................................................................................................. 18
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 2
PREFACE
This manual describes how to connect the Display and the External Device (target PLC).
In this manual, the connection procedure will be described by following the below sections:
1System Configuration
This section shows the types of External
Devices which can be connected and SIO
type.
)"1 System Configuration" (page 3)
2Selection of External Device
Select a model (series) of the External
Device to be connected and connection
method.
)"2 Selection of External Device" (page 7)
3Example of Communication Settings
This section shows setting examples for
communicating between the Display and
the External Device.
)"3 Example of Communication Setting" (page
8)
4Setup Items
This section describes communication
setup items on the Display.
Set communication settings of the Display
with GP-Pro EX or in offline mode.
)"4 Setup Items" (page 9)
Operation
5Cable Diagram
This section shows cables and adapters
for connecting the Display and the
External Device.
)"5 Cable Diagram" (page 14)
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 3
1 System Configuration
The system configuration in the case when the External Device of Siemens AG and the Display are connected is
shown.
Connection Configuration
[1:1 Connection]
Series Name CPU Link I/F SIO Type Setting
Example
Cable
Diagram
Series
90U-115U
CPU 90U
CPU 95U
CPU 100
CPU 102
CPU 103
CPU 941
CPU 942
CPU 943
CPU 944
CPU 945
PG port on CPU RS232C
Setting
Example 1
(page 8)
Cable
Diagram 1
(page 14)
Series
135U/155U
CPU 922
CPU 928
CPU 928B
CPU 946
CPU 947
CPU 948
PG port on CPU RS232C
• Set the execution time of the logic functions in the Display to “100 ms” or less. If the longer time is
set, an error may occur in the communication with the external device.
Display External Device
CA6-CBLTTY/5M-01
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 4
IPC COM Port
When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please
refer to the IPC manual for details.
Usable port
Series
Usable Port
RS-232C RS-422/485(4 wire) RS-422/485(2 wire)
PS-2000B COM1*1 , COM2,
COM3*1, COM4
*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.
--
PS-3450A, PS-3451A,
PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2
PS-3650A (T41 model),
PS-3651A (T41 model) COM1*1 --
PS-3650A (T42 model),
PS-3651A (T42 model) COM1*1*2, COM2 COM1*1*2 COM1*1*2
PS-3700A (Pentium®4-M)
PS-3710A
COM1*1, COM2*1,
COM3*2 , COM4
*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.
COM3*2 COM3*2
PS-3711A COM1*1, COM2*2 COM2*2 COM2*2
PS4000*3
*3 When making communication between an External Device and COM port on the Expansion slot,
only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the
specification of COM port.
For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.
Please refer to the IPC manual for details of pin layout.
COM1, COM2 - -
PL3000 COM1*1*2, COM2*1,
COM3, COM4 COM1*1*2 COM1*1*2
PE-4000B Atom N270 COM1, COM2 - -
PE-4000B Atom N2600 COM1, COM2 COM3*4 , COM4*4,
COM5*4, COM6*4
*4 Set up the SIO type with the BIOS. Please refer to the IPC manual for details of BIOS.
COM3*4, COM4*4,
COM5*4, COM6*4
PS5000 (Slim Panel Type
Core i3 Model) *5 *6 COM1, COM2*4 COM2*4 COM2*4
PS5000 (Slim Panel Type
Atom Model)
*5 *6
COM1, COM2*7 COM2*7 COM2*7
PS5000 (Enclosed Panel
Type)*8 COM1 - -
PS5000 (Modular Type
PFXPU/PFXPP)*5 *6
PS5000 (Modular Type
PFXPL2B5-6)
COM1*7 COM1*7 COM1*7
PS5000 (Modular Type
PFXPL2B1-4) COM1, COM2*7 COM2*7 COM2*7
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 5
DIP Switch settings (PL3000 / PS3000 Series)
RS-232C
*5 When setting up communication between an External Device and the RS-232C/422/485 interface
module, use the IPC (RS-232C) or PS5000 (RS-422/485) cable diagrams. However, when using
PFXZPBMPR42P2 in a RS-422/485 (4-wire) configuration with no flow control, connect 7.RTS+
and 8.CTS+, and connect 6.RTS- and 9.CTS-.
When using RS-422/485 communication with External Devices, you may need to reduce the
transmission speed and increase the TX Wait time.
*6 To use RS-422/485 communication on the RS-232C/422/485 interface module, the DIP Switch
setting is required. Please refer to "Knowledge Base" (FAQs) on the support site. (http://www.pro-
face.com/trans/en/manual/1001.html)
*7 Set up the SIO type with the DIP Switch. Please refer to the IPC manual for details of DIP Switch.
The BOX Atom has not a switch to set the RS-232C, RS-422/485 mode. Use the BIOS for the
setting.
*8 For the connection with the External Device, on the user-created cable read as if the connector on
the Display-side is a M12 A-coding 8 pin socket. The pin assignment is the same as described in
the cable diagram. For the M12 A-coding connector, use PFXZPSCNM122.
DIP Switch Setting Description
1OFF
*1
*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.
Reserved (always OFF)
2OFF
SIO type: RS-232C
3OFF
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF
Settings FAQ ID
PFXZPBMPR42P2, RS422/485 change method FA263858
PFXZPBMPR42P2 termination resistor setting FA263974
PFXZPBMPR44P2, RS422/485 change method FA264087
PFXZPBMPR44P2 termination resistor setting FA264088
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 6
RS-422/485 (4 wire)
RS-422/485 (2 wire)
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available
8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available
9ON
RS (RTS) Auto control mode: Enabled
10 ON
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 7
2 Selection of External Device
Select the External Device to be connected to the Display.
Setup Items Setup Description
Number of Devices/
PLCs Enter an integer from 1 to 4 to define the number of Devices/PLCs to connect to the display.
Manufacturer Select the manufacturer of the External Device to connect. Select "Siemens AG".
Series
Select the External Device model (series) and the connection method. Select "SIMATIC S5
CPU Direct".
In System configuration, make sure the External Device you are connecting is supported by
"SIMATIC S5 CPU Direct".
)"1 System Configuration" (page 3)
Port Select the Display port to connect to the External Device.
Use System Area
Check this option to synchronize the system data area of the Display and the device (memory)
of the External Device. When synchronized, you can use the External Device’s ladder
program to switch the display or display the window on the Display.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
This feature can also be set in GP-Pro EX or in the Display's offline mode.
Cf. GP-Pro EX Reference Manual "System Settings [Display Unit] - [System Area]
Settings Guide"
Cf. Maintenance/Troubleshooting Guide "Main Unit - System Area Settings"
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 8
3 Example of Communication Setting
Examples of communication settings of the Display and the External Device, recommended by Digital
Electronics Corp., are shown.
3.1 Setting Example 1
Settings of GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
Settings of External Device
The communication setting of the External Device is fixed.
You need not set it.
• When you use CPU 945, CPU946, CPU947 or CPU948, check the [Use CPU945] checkbox or
[Use CPU946/947/948] checkbox. The checkbox is switched depending on the series you select.
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 9
4 Setup Items
Set communication settings of the Display with GP-Pro Ex or in offline mode of the Display.
The setting of each parameter must be identical to that of External Device.
)"3 Example of Communication Setting" (page 8)
4.1 Setup Items in GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Setup Items Setup Description
SIO Type Displays the SIO type to communicate with the External Device.
Speed Displays the communication speed between the External Device and the Display.
Data Length Displays data length.
Parity Displays how to check parity.
Stop Bit Displays stop bit length.
Flow Control Displays the communication control method to prevent overflow of transmission and
reception data.
Timeout Use an integer from "1 to 127" to enter the time (s) for which the Display waits for the
response from the External Device.
Retry In case of no response from the External Device, use an integer from "0 to 255" to enter
how many times the Display retransmits the command.
Wait To Send Use an integer from "0 to 255" to enter standby time (ms) for the Display from receiving
packets to transmitting next commands.
SIMATIC S5 CPU Direct Driver
GP-Pro EX Device/PLC Connection Manual 10
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
RI/VCC
You can switch RI/VCC of the 9th pin if you select RS232C for SIO type.
It is necessary to change RI/5V by changeover switch of IPC when connect with IPC.
Please refer to the manual of the IPC for more detail.
• Refer to the GP-Pro EX Reference Manual for Indirect Device.
Cf. GP-Pro EX Reference Manual "Changing the Device/PLC at Runtime (Indirect
Device)"
Setup Items Setup Description
Series Select a model of the External Device.
Use CPU945 Select the checkbox when you use CPU 945. This checkbox is available when [S5 90U-
115U] is selected in [Series].
Use CPU946/947/948 Select the checkbox when you use CPU 946, CPU 947 or CPU 948. This checkbox is
available when [S5 135U/155U] is selected in [Series].
Setup Items Setup Description
Andere Handbücher für SIMATIC S5 CPU Direct Driver
1
Dieses Handbuch passt für folgende Modelle
16
Inhaltsverzeichnis
Andere Siemens Steuerungssystem Handbücher
Siemens
Siemens SINUMERIK 840D Handbuch
Siemens
Siemens SIMATIC PCS 7 Betriebsanleitung
Siemens
Siemens POWERS HU 186 Betriebsanleitung
Siemens
Siemens SIMATIC PCS 7 Bedienungsanleitung
Siemens
Siemens SIMATIC PCS 7 Bedienungsanleitung
Siemens
Siemens SINUMERIK 840D sl Kurzanleitung
Siemens
Siemens SINUMERIK ONE MCP 1500 Technisches Dokument
Siemens
Siemens SINUMERIK 828D Turning Bedienungsanleitung
Siemens
Siemens SIMATIC PCS 7 Installationsanleitung
Siemens
Siemens SIMATIC PCS 7 Kurzanleitung
Siemens
Siemens SINUMERIK 828D Turning Stücklistenhandbuch
Siemens
Siemens SIMATIC PCS 7 Merkblatt
Siemens
Siemens SIPLUS HCS Series Bedienungsanleitung
Siemens
Siemens simatic c7-621 Bedienungsanleitung
Siemens
Siemens SIMOTION Stücklistenhandbuch
Siemens
Siemens SIMATIC PCS 7 Stücklistenhandbuch
Siemens
Siemens SINUMERIK Betriebsanleitung
Siemens
Siemens DESIGO RX QAX33.1 Bedienungsanleitung
Siemens
Siemens SIMATIC C7-635 Bedienungsanleitung
Siemens
Siemens SINUMERIK 828D Turning Stücklistenhandbuch
