Siemens SINUMERIK ONE MCP 2200c Technisches Dokument

SINUMERIK

SINUMERIK ONE

ONE MCP Part 2: MCP 2200c

Equipment Manual

Valid for:

Control system

SINUMERIK ONE

SINUMERIK 840D sl/840DE sl

07/2020

A5E50324711B AA

Fundamental safety

instructions 1

Overview 2

Dimension drawings 3

Operator control and

display elements 4

Technical data 5

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage

to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices

referring only to property damage have no safety alert symbol. These notices shown below are graded according to

the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be

used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property

damage.

Quali󹪝ed Personnel

The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or

approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance

are required to ensure that the products operate safely and without any problems. The permissible ambient

conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identi󹪝ed by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may

be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described.

Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this

publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG

Digital Industries

Postfach 48 48

90026 NÜRNBERG

GERMANY

Document order number: A5E50324711B AA

Ⓟ 10/2020 Subject to change

Table of contents

1 Fundamental safety instructions ........................................................................................................... 5

1.1 General safety instructions................................................................................................... 5

1.2 Equipment damage due to electric 󹪝elds or electrostatic discharge ....................................... 8

1.3 Warranty and liability for application examples ..................................................................... 9

1.4 Security information ............................................................................................................ 9

1.5 Residual risks of power drive systems ................................................................................. 10

2 Overview.............................................................................................................................................. 13

3 Dimension drawings............................................................................................................................ 15

4 Operator control and display elements ............................................................................................... 17

4.1 Front side .......................................................................................................................... 17

4.2 Rear side............................................................................................................................ 18

5 Technical data...................................................................................................................................... 19

Index .................................................................................................................................................... 23

ONE MCP Part 2: MCP 2200c

Equipment Manual, 07/2020, A5E50324711B AA 3

Table of contents

ONE MCP Part 2: MCP 2200c

4Equipment Manual, 07/2020, A5E50324711B AA

Fundamental safety instructions 1

1.1 General safety instructions

WARNING

Electric shock and danger to life due to other energy sources

Touching live components can result in death or severe injury.

• Only work on electrical devices when you are quali󹪝ed for this job.

• Always observe the country-speci󹪝c safety rules.

Generally, the following steps apply when establishing safety:

1. Prepare for disconnection. Notify all those who will be a󹪜ected by the procedure.

2. Isolate the drive system from the power supply and take measures to prevent it being

switched back on again.

3. Wait until the discharge time speci󹪝ed on the warning labels has elapsed.

4. Check that there is no voltage between any of the power connections, and between any of

the power connections and the protective conductor connection.

5. Check whether the existing auxiliary supply circuits are de-energized.

6. Ensure that the motors cannot move.

7. Identify all other dangerous energy sources, e.g. compressed air, hydraulic systems, or

water. Switch the energy sources to a safe state.

8. Check that the correct drive system is completely locked.

After you have completed the work, restore the operational readiness in the inverse sequence.

WARNING

Electric shock due to connection to an unsuitable power supply

When equipment is connected to an unsuitable power supply, exposed components may carry

a hazardous voltage. Contact with hazardous voltage can result in severe injury or death.

• Only use power supplies that provide SELV (Safety Extra Low Voltage) or PELV- (Protective

Extra Low Voltage) output voltages for all connections and terminals of the electronics

modules.

ONE MCP Part 2: MCP 2200c

Equipment Manual, 07/2020, A5E50324711B AA 5

WARNING

Electric shock due to equipment damage

Improper handling may cause damage to equipment. For damaged devices, hazardous

voltages can be present at the enclosure or at exposed components; if touched, this can result

in death or severe injury.

• Ensure compliance with the limit values speci󹪝ed in the technical data during transport,

storage and operation.

• Do not use any damaged devices.

WARNING

Electric shock due to unconnected cable shields

Hazardous touch voltages can occur through capacitive cross-coupling due to unconnected

cable shields.

• As a minimum, connect cable shields and the cores of cables that are not used at one end

at the grounded housing potential.

WARNING

Electric shock if there is no ground connection

For missing or incorrectly implemented protective conductor connection for devices with

protection class I, high voltages can be present at open, exposed parts, which when touched,

can result in death or severe injury.

• Ground the device in compliance with the applicable regulations.

NOTICE

Damage to equipment due to unsuitable tightening tools.

Unsuitable tightening tools or fastening methods can damage the screws of the equipment.

• Be sure to only use screwdrivers which exactly match the heads of the screws.

• Tighten the screws with the torque speci󹪝ed in the technical documentation.

• Use a torque wrench or a mechanical precision nut runner with a dynamic torque sensor and

speed limitation system.

Fundamental safety instructions

1.1 General safety instructions

ONE MCP Part 2: MCP 2200c

6Equipment Manual, 07/2020, A5E50324711B AA

WARNING

Spread of 󹪝re from built-in devices

In the event of 󹪝re outbreak, the enclosures of built-in devices cannot prevent the escape of

󹪝re and smoke. This can result in serious personal injury or property damage.

• Install built-in units in a suitable metal cabinet in such a way that personnel are protected

against 󹪝re and smoke, or take other appropriate measures to protect personnel.

• Ensure that smoke can only escape via controlled and monitored paths.

WARNING

Unexpected movement of machines caused by radio devices or mobile phones

Using radio devices or mobile telephones in the immediate vicinity of the components can

result in equipment malfunction. Malfunctions may impair the functional safety of machines

and can therefore put people in danger or lead to property damage.

• Therefore, if you move closer than 20 cm to the components, be sure to switch o󹪜 radio

devices or mobile telephones.

• Use the "SIEMENS Industry Online Support app" only on equipment that has already been

switched o󹪜.

WARNING

Fire due to inadequate ventilation clearances

Inadequate ventilation clearances can cause overheating of components with subsequent 󹪝re

and smoke. This can cause severe injury or even death. This can also result in increased

downtime and reduced service lives for devices/systems.

• Ensure compliance with the speci󹪝ed minimum clearance as ventilation clearance for the

respective component.

NOTICE

Overheating due to inadmissible mounting position

The device may overheat and therefore be damaged if mounted in an inadmissible position.

• Only operate the device in admissible mounting positions.

Fundamental safety instructions

1.1 General safety instructions

ONE MCP Part 2: MCP 2200c

Equipment Manual, 07/2020, A5E50324711B AA 7

WARNING

Unexpected movement of machines caused by inactive safety functions

Inactive or non-adapted safety functions can trigger unexpected machine movements that

may result in serious injury or death.

• Observe the information in the appropriate product documentation before commissioning.

• Carry out a safety inspection for functions relevant to safety on the entire system, including

all safety-related components.

• Ensure that the safety functions used in your drives and automation tasks are adjusted and

activated through appropriate parameterizing.

• Perform a function test.

• Only put your plant into live operation once you have guaranteed that the functions

relevant to safety are running correctly.

Note

Important safety notices for Safety Integrated functions

If you want to use Safety Integrated functions, you must observe the safety notices in the Safety

Integrated manuals.

1.2 Equipment damage due to electric 󹪝elds or electrostatic discharge

Electrostatic sensitive devices (ESD) are individual components, integrated circuits, modules or

devices that may be damaged by either electric 󹪝elds or electrostatic discharge.

NOTICE

Equipment damage due to electric 󹪝elds or electrostatic discharge

Electric 󹪝elds or electrostatic discharge can cause malfunctions through damaged individual

components, integrated circuits, modules or devices.

• Only pack, store, transport and send electronic components, modules or devices in their

original packaging or in other suitable materials, e.g conductive foam rubber of aluminum

foil.

• Only touch components, modules and devices when you are grounded by one of the

following methods:

– Wearing an ESD wrist strap

– Wearing ESD shoes or ESD grounding straps in ESD areas with conductive 󹪞ooring

• Only place electronic components, modules or devices on conductive surfaces (table with

ESD surface, conductive ESD foam, ESD packaging, ESD transport container).

Fundamental safety instructions

1.2 Equipment damage due to electric 󹪝elds or electrostatic discharge

ONE MCP Part 2: MCP 2200c

8Equipment Manual, 07/2020, A5E50324711B AA

1.3 Warranty and liability for application examples

Application examples are not binding and do not claim to be complete regarding con󹪝guration,

equipment or any eventuality which may arise. Application examples do not represent speci󹪝c

customer solutions, but are only intended to provide support for typical tasks.

As the user you yourself are responsible for ensuring that the products described are operated

correctly. Application examples do not relieve you of your responsibility for safe handling when

using, installing, operating and maintaining the equipment.

1.4 Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is necessary

to implement – and continuously maintain – a holistic, state-of-the-art industrial security

concept. Siemens’ products and solutions constitute one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. Such systems, machines and components should only be connected to

an enterprise network or the internet if and to the extent such a connection is necessary and only

when appropriate security measures (e.g. 󹪝rewalls and/or network segmentation) are in place.

For additional information on industrial security measures that may be implemented, please

visit

https://www.siemens.com/industrialsecurity (https://www.siemens.com/industrialsecurity).

Siemens’ products and solutions undergo continuous development to make them more secure.

Siemens strongly recommends that product updates are applied as soon as they are available

and that the latest product versions are used. Use of product versions that are no longer

supported, and failure to apply the latest updates may increase customer’s exposure to cyber

threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed

under

https://www.siemens.com/industrialsecurity (https://new.siemens.com/global/en/products/

services/cert.html#Subscriptions).

Further information is provided on the Internet:

Fundamental safety instructions

1.4 Security information

ONE MCP Part 2: MCP 2200c

Equipment Manual, 07/2020, A5E50324711B AA 9

Industrial Security Con󹪝guration Manual (https://support.industry.siemens.com/cs/ww/en/

view/108862708)

WARNING

Unsafe operating states resulting from software manipulation

Software manipulations, e.g. viruses, Trojans, or worms, can cause unsafe operating states in

your system that may lead to death, serious injury, and property damage.

• Keep the software up to date.

• Incorporate the automation and drive components into a holistic, state-of-the-art industrial

security concept for the installation or machine.

• Make sure that you include all installed products into the holistic industrial security concept.

• Protect 󹪝les stored on exchangeable storage media from malicious software by with suitable

protection measures, e.g. virus scanners.

• On completion of commissioning, check all security-related settings.

1.5 Residual risks of power drive systems

When assessing the machine- or system-related risk in accordance with the respective local

regulations (e.g., EC Machinery Directive), the machine manufacturer or system installer must

take into account the following residual risks emanating from the control and drive components

of a drive system:

1. Unintentional movements of driven machine or system components during commissioning,

operation, maintenance, and repairs caused by, for example,

– Hardware and/or software errors in the sensors, control system, actuators, and cables and

connections

– Response times of the control system and of the drive

– Operation and/or environmental conditions outside the speci󹪝cation

– Condensation/conductive contamination

– Parameterization, programming, cabling, and installation errors

– Use of wireless devices/mobile phones in the immediate vicinity of electronic components

– External in󹪞uences/damage

– X-ray, ionizing radiation and cosmic radiation

2. Unusually high temperatures, including open 󹪞ames, as well as emissions of light, noise,

particles, gases, etc., can occur inside and outside the components under fault conditions

caused by, for example:

– Component failure

– Software errors

– Operation and/or environmental conditions outside the speci󹪝cation

– External in󹪞uences/damage

Fundamental safety instructions

1.5 Residual risks of power drive systems

ONE MCP Part 2: MCP 2200c

10 Equipment Manual, 07/2020, A5E50324711B AA

Inhaltsverzeichnis

Andere Siemens Steuerungssystem Handbücher

Siemens

Siemens SINUMERIK 840D sl Benutzerhandbuch

Siemens

Siemens SIMATIC PCS 7 BOX Bedienungsanleitung

Siemens

Siemens SINUMERIK Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Kurzanleitung

Siemens

Siemens SIPLUS HCS3200 Bedienungsanleitung

Siemens

Siemens SIMATIC 6ES7673-2CC40-0YA0 Bedienungsanleitung

Siemens

Siemens IR-64K Bedienungs- und Montageanleitung

Siemens

Siemens SIMATIC NET TeleControl SINAUT ST7 Benutzerhandbuch

Siemens

Siemens SIMATIC PCS 7 Stücklistenhandbuch

Siemens

Siemens SIMATIC PCS 7 Bedienungsanleitung

Siemens

Siemens SINUMERIK 802C Bedienungsanleitung

Siemens

Siemens SIMATIC PCS 7 Stücklistenhandbuch

Siemens

Siemens SIMATIC PCS 7 SMART Bedienungsanleitung

Siemens

Siemens SIMATIC PCS 7 FOUNDATION Fieldbus Kurzanleitung

Siemens

Siemens SINUMERIK 840D sl Kurzanleitung

Siemens

Siemens SINAUT ST7 Benutzerhandbuch

Siemens

Siemens SINUMERIK 840D sl Stücklistenhandbuch

Siemens

Siemens SIMATIC PC BI45 Stücklistenhandbuch

Siemens

Siemens SIDOOR ATD401W Benutzerhandbuch

Siemens

Siemens SINUMERIK 802D Beilage

Siemens

Siemens SINUMERIK 828D Turning Stücklistenhandbuch

Siemens

Siemens simatic c7-621 Handbuch

Siemens

Siemens SINUMERIK 802D sl Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung