Siemens 7SA513BB Series Bedienungs- und Montageanleitung

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö (readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 Rö SIEMENS AG Page

1B firmware 07.01.99 Rö PTD PA D SI

1A first issue 06.01.99 Rö PowerTransmission C53000-A1000-X015-1H-7620 1 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

Service-Information 7SA513 /BB.../EE

Firmware Update to V3.31 (EPROM Exchange)

Firmware version V3.31 for the line protection relay 7SA513 is available now.

•Affected are only devices with a DVH-module (see fig. 1), which are manufactured in the

release 5 or higher. Release 5 is already present in all devices with the hardware

version /CD or higher. For devices up to hardware version /CC, the DVH-release (≥5) is decisive

and has to be identified (compare to No. 8 of this service-information)!

(Object number of the DVH-module: C73207-A272-A5-*with* ≥5).

Attention! Devices with a DVH-module of an older release (≤4), a firmware-upgrade is only

possible by replacing the complete DVH-module! (Order procedure absolutely with declaration of

the MLFB-No. of the device incl. hardware version ( ... /* * ), Fab.-No. and required firmware

version).

•Notice for devices 7SA513*-*****-*C** with serial interface to a central data processing station

(e.g. LSA):

The normal signal position for the data transmission is factory preset as „light off“. A change of the

normal signal position to „light on“by a jumper plug is only possible on DVH-modules with the

release 6 (or higher), and is already present in all devices with hardware version /DD and higher.

SIEMENS

7SA513...

SIEMENS

Betrieb/Service

Störung/Blocked

+5V

+15V

-15V

+24V

HöSP-Abzweigschutz

EHV Line Protection

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 2 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

If operation with normal signal position „light on“is necessary, for devices up to hardware version

/CD the DVH-release (≥6) is decisive and has to be identified (compare No. 8 of this service-

information)!

In case the DVH-module has to be changed to a „light on/off - version (object-number: C73207-

A272-A5-*with* ≥6). Order procedure absolutely with declaration of the MLFB-No. of the device

incl. hardware version (... / * * ), Fab.-No. and required V3-firmware version.

Update-notice for DVH-modules with release 5 (or higher):

For devices 7SA513 with firmware, versions V2.1X/V2.2X/V3.XX the upgrade to version V3.31 can be

made with a loading program: Load the Flash-EPROM with the PC using the serial operator interface

(described in service information C53000-A1000-X016-1H-7620). The upgrade kit to V3.31 with the

loading program and the disk (3,5“DS HD for DOS-computers) can be ordered (see order data).

A firmware update via loading program from version V1.XX and V2.0X to version V3.31 is not

possible!

Devices with version V1.X or V2.0X can only be upgraded to V3.31 via EPROM-exchange.

If required, the upgrade to firmware version V3.31 can occur by EPROM-exchange (described in this

service information C53000-A1000-X015-1H-7620). For that the EPROM-update kit for V3.31 is

indispensable (see order data).

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 3 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

This service information ´C53000-A1000-X015-1H-7620´ describes the update by exchanging the

EPROMs.

The update set can be ordered at:

SIEMENS AG

PTD PA PTL 1

Wernerwerkdamm 5

13623 Berlin

Germany

Order number for update sets 7SA513:

Firmware EPROM-set Loading program

V3.31 C73207-A272-D515-2 C73207-A272-W522-2

Please specify in your Order:

•Number of devices

•MLFB No.

•Fab.-No.

•Previous firmware version

•Required firmware version (V3.31)

•Clarification, if full VDEW-compatible DVH-module is required

(„light on / light off“- jumper plug)

Ordering procedure via AGAVE, LABIV, SAP etc.

Order forms to UMWB

The firmware exchange may only be carried out by qualified persons.

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 4 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

We recommend observing the following procedure when updating the firmware:

Observe the ESD guidelines.

W A R N I N G

When carrying out modifications locally, it is

absolutely necessary to observe the guidelines

for handling electrostatic sensitive devices

(ESD).

Update to firmware V3.31:

1. After the firmware exchange, the device will revert to the original factory settings.

2. Observe the relevant ESD (Electrostatic Sensitive Devices) precautions.

3. Remove the front cover of the device (turn up the folds that cover the rack both at the top and

at the bottom and remove the four screws under the folds).

4. Before exchanging the firmware, read out or write down the settings and marshallings of the

protection device by using an operator panel/display, 7XR50 or laptop/PC with DIGSI.

5. Switch off the device (e.g. at the front-side slide-switch).

6. Loosen the screws on the right hand side of the front door and open the front door of the relay.

7. Carefully remove the ribbon cables which connect the DVH-module (see fig. 1, pos (2) on page

12) with the other modules, that the DVH-module can be pulled out.

Afterwards remove the other ribbon cables which connect the front panel with the

- operational interface

- LCD-display

- membrane keyboard

8. Pull the DVH module out of the relay (see fig. 1, pos (2) on page 12) and place it on

the conductive surface.

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 5 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

On the DVH-module a label with -A272-A5-* is fixed. This label characterises the complete

module as a DVH-module. The release is labeled at the point of the star (*).

Example: -A272-A5-5).

The release of the module has to be checked.

--> The release of the DVH-module must be 5 or higher !

Note:

•The firmware update as shown in this service-information is only possible with a DVH-

module having a release of 5 or higher (≥5).

•Devices with a DVH-module of an older release (≤4), a firmware-upgrade is only possible by

replacing the complete DVH-module! (Order procedure absolutely with declaration of the

MLFB-No. of the device incl. hardware version .../**(!), Fab.-No. and required firmware

version).

Notice for devices 7SA513*-*****-*C** with serial interface to a central data processing

station (LSA):

•The normal signal position for the data transmission is factory preset as „light off“.

•A change of the normal signal position to „light on“by a jumper plug is only possible on

DVH-modules with the release 6 (or higher).

•If operation with normal signal position „light on“is necessary, the DVH-module has to be

changed to a „light on/off - version (DVH-release ≥6).

Order procedure absolutely with declaration of the MLFB-No. of the device incl. hardware

version .../* *(!), Fab.-No. and required firmware version.

9. The DVH-module has to be opened:

- The DVH module has to be placed on the conductive surface with the ZPH-board (DVH

module-part with the red and green LED) facing to the conductive surface.

- Now the MVH-board is facing upwards (see fig. 2 on page 12) and the 3 screws C, D a. E

and screws A and B of the plug-module have to be removed.

- Turn up the two module-parts of the DVH-module (ZPH and MVH module) and put them side

by side as shown in fig. 3 on page 13.

The two DVH-modules composing of modules MVH and ZPH are labeled as follows:

MVH ---> - A272 - B20 - * ZPH ---> - A272 - B30 - *

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 6 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

10. Carefully remove the EPROMs (previous firmware version) with the enclosed PLCC - extraction

tool out of the IC-locations (see fig. 3 on page 13) by levering out of its IC bases.

The EPROM´s are located at the following positions:

- ZPH module: D11 and D12

- MVH module: D28, D29, D30 and D31

11. Carefully insert the new EPROMs in the sockets of the ZPH and MVH module (see fig. 3 on

page 13). Make sure that the IC identifier corresponds to the base identifier and that no terminal

pins of the EPROMs suffer injury (bending) during insertion.

Module (No.) IC-Position V3.31 EPROM labeled with

ZPH (-A272-B30-*) D11 P73509-B1-A191-2

D12 P73509-B1-A192-2

MVH (-A272-B20-*) D28 P73509-B1-A185-2

D29 P73509-B1-A186-2

D30 P73509-B1-A187-2

D31 P73509-B1-A188-2

12. The DVH module has to be assembled again (reverse order as described under 9):

- Place the MVH-module on the top of ZPH module.

- Bring the drilled holes of the DVH-board in accordance with the tapped holes and

the plug-module.

- The three screws C, D, E and screws A and B of the plug-module, which is facing

upwards (see fig. 2 on page 12) have to be fixed.

13. To indicate that the firmware has been updated, a label should be attached to the lower side of

the ZPH-processor board. Use the supplied label and fix it on a suitable location (e.g. covering

the former label).

14. Insert the DVH module into the housing; ensure that the module is firmly pushed in.

W A R N I N G !

Improper handling of the PLCC-extraction tool or false EPROM-placing causes injury for the

EPROM-sockets.

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 7 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

15. Carefully re-connect the ribbon cables which connect the DVH-module (see fig. 1, pos (2) on

page 12) with the other modules.

Then re-connect the ribbon cables from the front panel; take care for correct polarity:

- from the operational interface

- from the LCD-display

- from the membrane keyboard

16. The update should now also be indicated externally by the appropriate label on the inner side of

the door of the housing. Use the supplied new label to replace the previous invalidated label.

If the firmware is updated from V2.** to version V3.**, the MLFB-code on the nameplate

(underneath the operator panel) should be modified. Correct the 11th position of the MLFB code

in accordance with the newly installed version V3 (using a water-resistant pen):

- for Version V3.** ---> 11th MLFB position = 2 : 7SA513*-***2*-****

17. Close the front door of the relay.

18. The two screws of the front door have to be fixed (see No. 6).

19. Switch on the device.

After switching on the DC power supply, there are two possibilities of response:

20. Possibility 1: The device switches into monitor mode (after 30 sec. max.).

Display: MONITOR-EINSTIEG

FEHLERREAKTION MONITOR-START

ORIG. START NEC.

Continue with No. 22

21. Possibility 2: Start-up of device:

Press: CW CW

Display: CODEWORTEINGABE: ENTER CODEWORD

Press: 333333 333333

Display: @@@@@@ @@@@@@

Press: E E

Display: CW AKZEPTIERT CW ACCEPTED

Press: DA DA

Display: DIREKTE ADRESSE DIRECT ADDRESS

Press: 9802 9802

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 8 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

Display: 9802 MONITOR

START ? 9802 MONITOR

START ?

Press: J/Y J/Y

On the display appears:

Display: MONITOR EINSTIEG

BEDIENUNG MONITOR-START

INTEGR. OPERAT.

22. In the monitor mode, please press down the keys slowly and firmly.

Press: CW CW

Display: CODEWORTEINGABE: ENTER CODEWORD:

Press: 000000 000000

Display: @@@@@@ @@@@@@

Press: E E

Display: CW AKZEPTIERT CW ACCEPTED

Press: E E

Display: MONITOR V3.1

FUNKTIONSAUSWAHL MONITOR V3.1

FUNCT. CHOICE

Press: ⇑⇑

several times until

Display: FUNKTIONSAUSWAHL

URANLAUF FUNCT. CHOICE

ORIGINAL START

appears

Press: E E

Display: CODEWORTEINGABE: ENTER CODEWORD:

Press: 333333 333333

Display: @@@@@@ @@@@@@

Press: E E

Display: CW AKZEPTIERT CW ACCEPTED

Press: E E

Display: URANLAUF

START ORIGINAL START

BEGIN

Within the next 90 sec. the display changes to

Display: URANLAUF

ENDE ORIGINAL START

END

After approx. 20 sec. the relay starts automatically and on the display appears:

Display: 0 7SA513 V3.31

7SA513****2***** 0 7SA513 V3.31

7SA513****2*****

The display indicates the new implemented firmware version (according to V3.31 and the

MLFB number *) of the device.

*) Please note: For updates V2.XX --> V3.XX, the 11th position of the MLFB-code for V3 has

changed to cipher „2“(for V2 cipher „1 “). The other positions are unchanged.

Note:

The modules have to be ordered in accordance to the MLFB-No. of the device!

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 9 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

As against the versions V2.1X/V2.2X the monitoring functions (which are preventing readiness

of service of the device in case of respond) concerning auxiliary supply monitoring and hard-

ware extension have been intensified. Therefore, the following point has to be checked

prophylactically.

•5V-auxiliary supply: At some devices SA513, the 5V-auxiliary supply has been balanced

at the upper tolerance limit. This can effect; that in certain circumstances the internal

supply monitoring is responding.

Up to V12, only registrations in the process signal buffer were ensued, but the functions

of the device were without affection.

With versions V2.2X/V3.XX, the device is switching in the blocking mode when the 5V-

monitoring is responding.

Help: Check/adjustment of the 5V-auxiliary supply (see No. 26).

23. After successful start, the green LED is illuminated to indicate readiness of service.

The display shows the MLFB-code of the device indicating the newly installed firmware.

The settings stored in the device are the original factory settings.

24. The device is now ready for normal commissioning.

25. The replaced EPROMs must be properly disposed of.

In written inquiries, please always specify the serial number and the complete

MLFB code for the device/component in question.

Date 22.04.1999

Name Röse

1H firmware 26.06.01 ZC Tested Claus

1G firmware 11.04.01 ZC Stand.

1D firmware 22.04.99 Rö(readme_EPROM_BB_EE.doc)

1C firmware 07.01.99 RöSIEMENS AG Page

1B firmware 07.01.99 RöPTD PA D SI

1A first issue 06.01.99 RöPower Transmission C53000-A1000-X015-1H-7620 10 / 13

Iss. Type of notice Date Name and Distribution

SIEMENS AG

Proprietary data, confidential

Service-Information

7SA513 /BB.../EE V1/V2/V3.XX --> V3.31

Firmware update via EPROM exchange

26. Measures for note-position „5V-auxiliary supply“(No. 23 of this information):

For check/adjustment of the 5V-auxiliary supply, the door of the housing must be opened.

26.1 Switch off the primary power supply.

26.2 Remove the bus plug -X11 from the power supply module SVH (see fig. 1).

26.3 Connect a digital-voltmeter to pin 2 (positive pole ´+5V) and pin 5 (negative pole ´M5V)

of the plug connector X11 (SVH-module). Pin-location see fig. 1.

26.4 Switch on the power supply.

26.5 The measured voltage must be 5,00 Volt. The tolerance is + 0,150 Volt.

26.6 If the voltage is within the tolerance, go to No. 26.14.

26.7 Voltage too high or too low?

26.8 Switch off the power supply.

26.9 Pull out the SVH-module out of the housing for approx. 6 cm.

26.10 Adjust potentiometer R15 with a suitable screwdriver or balancing pin threw the drilled

hole of the right SVH-module:

- Voltage too high --> Adjust the potentiometer approx. 5°clockwise.

- Voltage too low --> Adjust the potentiometer approx. 5°anti-clockwise.

26.11 Push the SVH-module back into the housing.

26.12 Switch on the power supply.

26.13 Go on with No. 26.5.

26.14 Switch off the power supply.

26.15 Replace the bus plug -X11 to the plug connector X11 of the power supply module SVH

(see fig. 1).

26.16 The check/adjustment of the 5V-auxiliary supply is finished.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SIMOCODE pro Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 7XT7100-0 A00/EE Series Bedienungsanleitung

Siemens

Siemens SINAMICS G120 Kurzanleitung

Siemens

Siemens SINAMICS G120 Bedienungsanleitung

Siemens

Siemens SINAMICS RAILCTRL Stücklistenhandbuch

Siemens

Siemens SINAMICS S110 Datenblatt

Siemens

Siemens S-60 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens LAL Series Bedienungsanleitung

Siemens

Siemens Simatic SM331 Bedienungsanleitung

Siemens

Siemens LVM Bedienungsanleitung

Siemens

Siemens SIMATIC 500 Series Handbuch

Siemens

Siemens 3RK2 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK 840Di sl Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 1243-1 DNP3 Merkblatt

Siemens

Siemens VRD Series Betriebsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SZE-4X Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200AL Bedienungsanleitung

Siemens

Siemens 3VL92 Series Bedienungsanleitung

Siemens

Siemens SIPROTEC Bedienungsanleitung

Siemens

Siemens Cerberus Pyrotronics LP-30 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SINAMICS SM120 Betriebsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung