Siemens SIMATIC S7 3964 Gebrauchsanweisung

Siemens AG

SIMATIC S7 3964(R)/

RK512 Driver

1 System Configuration.......................................................................................................3

2 Selection of External Device............................................................................................4

3 Example of Communication Setting.................................................................................5

4 Setup Items....................................................................................................................11

5 Cable Diagram...............................................................................................................16

6 Supported Device...........................................................................................................18

7 Device Code and Address Code....................................................................................19

8 Error Messages..............................................................................................................20

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect the Display (GP3000 series) and the External Device (target PLC).

In this manual, the connection procedure will be described by following the below sections:

1System Configuration

This section shows the types of External

Devices which can be connected and SIO

type.

)"1 System Configuration" (page 3)

2Selection of External Device

Select a model (series) of External Device

to be connected and connection method.

)"2 Selection of External Device" (page 4)

3Example of Communication Settings

This section shows setting examples for

communicating between the Display and

the External Device.

)"3 Example of Communication Setting" (page

4Setup Items

This section describes communication

setup items on the Display.

Set communication settings of the Display

with GP-Pro EX or in off-line mode.

)"4 Setup Items" (page 11)

5Cable Diagram

This section shows cables and adapters

for connecting the Display and the

External Device.

)"5 Cable Diagram" (page 16)

Operation

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The system configuration in the case when the External Device of Siemens AG and the Display are connected is

shown.

Series CPU Module Link I/F SIO Type Setting Example Cable Diagram

SIMATIC

S7-300 Series

CPU312IFM

CPU313

CPU314

CPU314IFM

CPU315

CPU315-2 DP

CPU316

CPU316-2 DP

CPU318-2

CP341

(RS232C) RS232C Setting Example 1

(page 5) Cable Diagram 1

(page 16)

CP341

(RS422/485) RS422/485

(4wire) Setting Example 2

(page 8) Cable Diagram 2

(page 17)

SIMATIC

S7-400 Series

CPU412-1

CPU412-2 DP

CPU413-1

CPU413-2 DP

CPU414-1

CPU414-2 DP

CPU414-3 DP

CPU416-1

CPU416-2 DP

CPU416-3 DP

CPU417-4

CP441-2

RS232C Setting Example 1

(page 5) Cable Diagram 1

(page 16)

RS422/485

(4wire) Setting Example 2

(page 8) Cable Diagram 2

(page 17)

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 4

2 Selection of External Device

Select the External Device to be connected to the Display.

Setup Items Setup Description

Maker Select the maker of the External Device to be connected. Select "Siemens AG".

Driver

Select a model (series) of the External Device to be connected and connection method.

Select "SIMATIC S7 3964(R)/RK512".

Check the External Device which can be connected in "SIMATIC S7 3964(R)/RK512" in

system configuration.

)"1 System Configuration" (page 3)

Use System Area

Check this option when you synchronize the system data area of the Display and the device

(memory) of the External Device. When synchronized, you can use the ladder program of

the External Device to switch the display or display the window on the Display.

Cf. GP-Pro EX Reference Manual "Appendix 1.4 LS Area (only for direct

access method)"

This can be also set with GP-Pro EX or in off-line mode of the Display.

Cf. GP-Pro EX Reference Manual "System Area Setting, 6.13.6 Setting Guide

of [System Setting Window]"

Cf. GP3000 Series User Manual "4.3.6 System Area Setting"

Port Select the Display port to be connected to the External Device.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 5

3 Example of Communication Setting

Examples of communication settings of the Display and the External Device, recommended by Pro-face, are

shown.

3.1 Setting Example 1

Setting of GP-Pro EX

Communication Settings

To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.

Device Setting

To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific

Settings] of [Device/PLC Settings].

When [Allowable No. of Device/PLCs] is multiple, you can click from [Device-Specific Settings] of

[Device/PLC Settings] to add External Device which is available to set.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 6

Settings of External Device

(1) Startup "SIMATIC Manager" and create the new project. Set the optional project name and click [OK]. New

project is created.

(2) From the menu bar, select [Insert], [Station], [Name of CPU type to use] (ex: [1 SIMATIC 400 Station]) in this

order.

(3) [(Name of CPU type to use)] (ex: [SIMATIC 400 (1)]) is created in the project. Double-click [Hardware] of

the name of CPU type to use.

(4) When the [HW Config] screen displayed, open [(Name of CPU type to use)], [(RACK type to use)] (ex:

[SIMATIC 400], [RACK-400]) in this order from the left tree and select the base unit of the using model.

(5) Drag & drop the selected base unit to the upper right window. The rack figure is created in the window.

(6) Drag & drop the using power unit in the rack.

(7) Similarly, drag & drop the using CPU unit.

(8) When using CPUxxx-xDP, the [Properties - PROFIBUS interface DP] dialog box is displayed. In that case,

click [Cancel] and close the dialog box.

(9) Similarly, drag & drop the using link unit.

(10)Double-click the CPU unit dropped in the rack.

(11)When the [MPI port] setting dialog box is displayed, click [Properties].

(12)Click [Properties] as "MPI(1) 187.5 Kbps" is selected as default. The value entered in [Address] this time

becomes the Destination Node No. (PLC Address) you set in GP-Pro EX. The default is "2".

(13)To change the speed [Transmission rate] and the highest value of the node No. [Highest MPI address], click

the [Network Settings] tab.

Select [187.5Kbps] for [Transmission rate]. To change the highest value of the node No. (Highest MPI

address), check [Change] to allow you to select from the list.

(14)When you finish setting, click [OK] and close the dialog box.

(15)Close other dialog boxes similarly.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 7

(16)Select [(Name of CPU type to use)] in the project, and open [Blocks] in the program, then double-click

[OB1].

(17)Here, you need to arrange the ladder program. Sample ladder program is shown below.

(18)Next, double-click [Hardware] in the CPU.

(19)Double-click the link unit as the link unit to use is already registered by the previous operation.

(20)To enable the communication between the External Device and the Display, click the [Parameter] button.

(21)The Parameter window is displayed. Select [RK512] from the [Protocol] list box and double-click the

[Protocol] image in the window.

(22)When the [Protocol] dialog box is displayed, set in the [RK 512] tab as below.

(23)When you finish setting, click [OK] and close the dialog box.

Setup Items Setup Description

With Block Check Check

Use Default Values Check

Transmission Rate 9600 bps

Stop Bits 1

Parity Even

Priority Low

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 8

3.2 Setting Example 2

Setting of GP-Pro EX

Communication Settings

To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.

Device Setting

To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific

Settings] of [Device/PLC Settings].

When [Allowable No. of Device/PLCs] is multiple, you can click from [Device-Specific Settings] of

[Device/PLC Settings] to add External Device which is available to set.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 9

Settings of External Device

(1) Startup "SIMATIC Manager" and create the new project. Set the optional project name and click [OK]. New

project is created.

(2) From the menu bar, select [Insert], [Station], [(Name of CPU type to use)] in this order.

(3) [(Name of CPU type to use)] is created in the project. Double-click [Hardware] of the name of CPU type to

use.

(4) When the [HW Config] screen displayed, open [(Name of CPU type to use)], [(RACK type to use)] in this

order from the left tree and select the base unit of the using model.

(5) Drag & drop the selected base unit to the upper right window. The rack figure is created in the window.

(6) Drag & drop the using power unit in the rack.

(7) Similarly, drag & drop the using CPU unit.

(8) When using CPUxxx-xDP, the [Properties - PROFIBUS interface DP] dialog box is displayed. In that case,

click [Cancel] and close the dialog box.

(9) Similarly, drag & drop the using link unit.

(10)Double-click the CPU unit dropped in the rack.

(11)When the [MPI port] setting dialog box is displayed, click [Properties].

(12)Click [Properties] as "MPI(1) 187.5 Kbps" is selected as default. The value entered in [Address] this time

becomes the Destination Node No. (PLC Address) you set in GP-Pro EX. The default is "2".

(13)To change the speed [Transmission rate] and the highest value of the node No. [Highest MPI address], click

the [Network Settings] tab.

Select [187.5Kbps] for [Transmission rate]. To change the highest value of the node No. (Highest MPI

address), check [Change] to allow you to select from the list.

(14)When you finish setting, click [OK] and close the dialog box.

(15)Close other dialog boxes similarly.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 10

(16)Select [(Name of CPU type to use)] in the project, and open [Blocks] in the program, then double-click

[OB1].

(17)Here, you need to arrange the ladder program. Sample ladder program is shown below.

(18)Next, double-click [Hardware] in the CPU.

(19)Double-click the link unit as the link unit to use is already registered by the previous operation.

(20)To enable the communication between the External Device and the Display, click the [Parameter] button.

(21)The Parameter window is displayed. Select [RK512] from the [Protocol] list box and double-click the

[Protocol] image in the window.

(22)When the [Protocol] dialog box is displayed, set in the [RK 512] tab as below.

(23)When connecting CP341/CP441 with RS422/485, double-click the [Interface] tab and select [None] in [Initial

State of the Receive Line].

(24)When you finish setting, click [OK] and close the dialog box.

Setup Items Setup Description

With Block Check Check

Use Default Values Check

Transmission Rate 9600 bps

Stop Bits 1

Parity Even

Priority Low

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Steuereinheit Handbücher

Siemens

Siemens SIRIUS 3RW5 series Bedienungsanleitung

Siemens

Siemens VBI60.15-5L Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Betriebsanleitung

Siemens

Siemens SIMATIC NET CP 343-2 Bedienungsanleitung

Siemens

Siemens SAFEDLINK Leitfaden

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens 3VL93 Series Bedienungsanleitung

Siemens

Siemens FN2013-U1 Bedienungsanleitung

Siemens

Siemens AP 641 Service-Handbuch

Siemens

Siemens SINAMICS G120P CU230P-2 Administratorhandbuch

Siemens

Siemens RUGGEDCOM RS900 Bedienungsanleitung

Siemens

Siemens Flowrite 599 Series Betriebsanleitung

Siemens

Siemens Climatix POL822 Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU1803-3NB00-1AE1 Bedienungsanleitung

Siemens

Siemens EcoView Bedienungsanleitung

Siemens

Siemens CLS-1000 Gebrauchsanweisung

Siemens

Siemens SINAMICS G120 CU250S-2 Series Administratorhandbuch

Siemens

Siemens XLD-1 Bedienungsanleitung

Siemens

Siemens SENTRON PAC RS485 Bedienungsanleitung

Siemens

Siemens ZU-35 Bedienungsanleitung

Siemens

Siemens Simatic S5 IP 240 Technisches Dokument

Siemens

Siemens SINAMICS S110 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA2712 Technisches Dokument

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung