Siemens OpenAir GDE141.1U Betriebsanleitung

Siemens Industry, Inc.

Technical Instructions

Document No. 155-784

October 20, 2016

OpenAir® Electronic Damper Actuators

GDE Series

Enhanced Non-spring Return Rotary

Description

The OpenAir direct coupled enhanced non-spring return rotary electric actuators are

designed for two-position/floating or modulating control of dampers.

Features

Selectable modulating control signal (0 to 10 Vdc or 2 to 10 Vdc).

24 Vac/dc compatible.

New line voltage (34x models) for 100 to 240 Vac two-position/floating control.

Integral 1/2-inch conduit connection.

Manual override.

Independently adjustable dual auxiliary switches available.

cUL and UL listed; certified

Application

These actuators are used in constant or variable air volume installations for control of

HVAC dampers requiring up to 44 lb-in (5 Nm) of torque.

Product Numbers Table 1.

Torque

Product Number

Control

Signal

Feedback

Dual

Auxiliary

Switches

Pre-Cabled

Power Supply

44 lb-in

(5 Nm)

GDE141.1U

2-position/

Floating

—

Standard

24 Vac/dc

GDE141.1U/B (24 pk)

—

Standard

GDE141.1P

—

Plenum

GDE141.1P/B (24 pk)

—

Plenum

GDE141.1Q

—

6-ft length

GDE142.1P*

•

—

Plenum

GDE146.1P*

—

•

Plenum

GDE341.1U

—

Standard

100 to 240 Vac

GDE346.1U*

•

Standard

GDE161.1P

Modulating

0(2) to 10 Vdc

•

—

Plenum

24 Vac/dc

GDE161.1P/B (24 pk)

•

—

Plenum

GDE161.1Q

•

—

6-ft length

GDE163.1P

•

—

Plenum

GDE164.1P*

•

Plenum

GDE166.1P*

•

Plenum

* For conduit adaption, order an ASK76.1U Conduit Adapter. See Accessories.

Technical Instructions OpenAir® GDE Enhanced Non-Spring Return Rotary Electronic Damper Actuator

Document Number 155-784

October 20, 2016

Page 2 Siemens Industry, Inc.

Specifications

Power Supply

Operating voltage (G–G0) 24 Vac/dc +/-20%

100 to 240 Vac +/-10%

Frequency 50/60 Hz

Power consumption VA Watt

GDE14x 2.5 1

GDE34x 5 1.6

GDE16x 2.1 1.2

Control signal

Input signal (Y-G0)

Voltage-input 0(2) to 10 Vdc

Input resistance >100K ohms

Feedback signal

Position output signal (U–G0)

Voltage-output 0 to 10 Vdc

Maximum output current DC 1 mA

Equipment rating

Rating Class 2 according to UL, cUL

Class III per EN60730

Auxiliary features

Control signal adjustment

Offset (start point) Between 0 to 5 Vdc

Slope (span) Between 2 and 30 Vdc

Dual auxiliary switch contact rating 4A resistive, 2A inductive

Voltage

GDE1xxx.P 24 Vac/24 Vdc

GDE3xxx.x 250 Vac

DC rating 12 to 30 Vdc

DC 2A

Switch Range

Switch A 0° to 90° with 5° intervals

Recommended range usage 0° to 45°

Factory setting 5°

Switch B 0° to 90° with 5° intervals

Recommended range usage 45° to 90°

Factory setting 85°

Switching hysteresis: 2°

Feedback potentiometer (GDE142.1P)

Sliding contact (P2) 0 to 5000 ohm <10 mA

Load <1 W

Voltage UL-Class 2 (SELV/PELV for CE)

<24 Vac/dc

Function

Torque 44 lb-in (5 Nm)

Runtime for 90° opening or closing 90 sec. at 60 Hz (125 sec. at 50 Hz)

Nominal angle of rotation 90°

Maximum angular rotation 95°

Mounting

Shaft size: Minimum shaft length 3/4-inch (20 mm)

Figure 1. Acceptable Shaft Sizes.

OpenAir® GDE Enhanced Non-Spring Return Rotary Electric Damper Actuator Technical Instructions

Document Number 155-784

October 20, 2016

Siemens Industry, Inc. Page 3

Specifications, continued

Housing

Enclosure NEMA Type 2

IP54 according to EN60529

(Not with cable-up mounting

orientation.)

Material Durable plastic

Gear lubrication Silicone-free

Ambient conditions

Ambient temperature

Operation -25°F to 130°F (-32°C to 55°C)

Storage and transport -40°F to 158°F (-40°C to 70°C)

Ambient humidity (non-condensing) 95% rh

Agency certification

UL listed to UL60730

cUL certified to Canadian

Standard C22.2 No. 24-93

These devices were approved for installation in plenum areas by Underwriters

Laboratories, Inc., per UL 1995.

EN60730-1, EN60730-2-14

Miscellaneous

Pre-cabled connection 18 AWG

Standard cable length 3 ft (0.9 m)

Life cycle Designed for 100,000 full strokes and

5 million repositions at rated torque

and temperature

Actuator Dimensions, inches (mm) 6.6 L × 2.8 W × 2.4 D

(166.7 L × 71 W × 61 D)

Packaging Dimensions, inches (mm) 6.5 L × 10.3 W × 3.1 D

(165.1 L × 261.1 W × 78.7 D)

Weight 1.35 lb (0.61 kg)

(with packaging) 1.91 lb (0.87 kg)

Accessories

NOTE: The auxiliary switches cannot be added in the field. Order the product

number that includes this option. See Table 1.

Figure 2. Conduit Adapter.

ASK76.1U: Provides a connection between

the actuator and conduit for actuator

models with auxiliary switches or built-in

potentiometers. All other standard actuator

models have built-in conduit adapters.

Figure 3. Rotary-to-Linear.

ASK71.5: Allows a direct-coupled

actuator to provide an auxiliary

linear drive.

Technical Instructions OpenAir® GDE Enhanced Non-Spring Return Rotary Electronic Damper Actuator

Document Number 155-784

October 20, 2016

Page 4 Siemens Industry, Inc.

Accessories,

Continued

Figure 4. Rotary-to-Linear with Bracket.

ASK71.6: Allows economical

mounting of an OpenAir actuator

to a variety of surfaces.

Should be used in applications

where the actuator can be rigid-

surface mounted and a linear

stroke output is needed.

Figure 5. Shaft Insert.

ASK78.3U: Shaft inserts for use

with 3/8-inch (8 to 10 mm)

diameter shafts. (10/pk).

Included in box with GDE/GLB

Series.

NOTE: Factory-installed 1/2-

inch guide must be

removed prior to

installation.

Figure 6. 1/2-inch Shaft Guide.

985-101P25: Shaft guide, 1/2-inch (25/pk).

Factory-installed with GDE/GLB Series.

Figure 7. NEMA Type 4X Weather Shield.

ASK75.7U: GDE Actuators are UL listed to

meet NEMA Type 4X requirements (a

degree of protection against falling dirt,

rain, sleet, snow, windblown dust,

splashing water, hose-directed water,

corrosion, and damage from external ice

formation) when installed with an

ASK75.7U Weather Shield and outdoor-

rated conduit fittings. This weather shield

may be mounted in any orientation.

For dimensions, see Figure 30.

OpenAir® GDE Enhanced Non-Spring Return Rotary Electric Damper Actuator Technical Instructions

Document Number 155-784

October 20, 2016

Siemens Industry, Inc. Page 5

Actuator

Components

2-Position/

Floating

Figure 8. Parts of the Actuator.

Legend

1. Base plate

2. Positioning scale for angle of rotation

3. Rotation direction adjustment

4. Conduit adapter

5. Connection cable

6. Manual override

7. Coupling bushing

8. Factory-installed 1/2-inch guide

9. Auxiliary Switch A

10. Auxiliary Switch B

11. Position indicator

12. Adjustment lever with

locking screw (4 mm hex)

13. Set screw for mechanical

range stop (4 mm hex)

14. Mounting bracket

Technical Instructions OpenAir® GDE Enhanced Non-Spring Return Rotary Electronic Damper Actuator

Document Number 155-784

October 20, 2016

Page 6 Siemens Industry, Inc.

Actuator

Components,

Continued

Modulating

Figure 9. Parts of the Actuator.

Legend

1. Base plate

2. Positioning scale for angle of rotation

3. Slope adjustment

4. Offset (start point) adjustment

5. DIP switches

6. Cover for DIP switches

7. Conduit adapter

8. Connection cable

9. Manual override

10. Coupling bushing

11. Factory-installed 1/2-inch guide

12. Auxiliary Switch A

13. Auxiliary Switch B

14. Position indicator

15. Adjustment lever with

locking screw (4 mm hex)

16. Set screw for mechanical

range stop (4 mm hex)

17. Mounting bracket

Operation

A continuous 0(2) to 10 Vdc signal from a controller to wire 8 (Y) operates the damper

actuator. The angle of rotation is proportional to the control signal. A 0 to 10 Vdc position

feedback output signal is available between wire 9 (U) and wire 2 (G0) to monitor the

position of the damper motor.

In the event of a power failure, the actuator holds its position. In the event that only the

control signal is lost, the actuator returns to the 0position.

Life expectancy

An improperly tuned loop will cause excessive repositioning that will shorten the life of

the actuator.

Control signal

adjustment

GDE163.1P and GDE164.1P: For sequencing and the electronic limitation of the angle

of rotation.

Use the Uo potentiometer to set the offset (start point) between 0 to 5 Vdc.

Use the U potentiometer to set the slope (span) between 2 to 30 Vdc.

NOTE: The Y input is limited to a maximum of 10 Vdc. If the sum of the offset and

slope setting is greater than 10V, the angle of rotation is reduced providing the

feature of electronic limitation of the angle of rotation.

OpenAir® GDE Enhanced Non-Spring Return Rotary Electric Damper Actuator Technical Instructions

Document Number 155-784

October 20, 2016

Siemens Industry, Inc. Page 7

Control signal

adjustment,

continued

Figure 10.

Ys Actuator position (100% = angle of rotation 90°*)

Y Control input signal

Uo Offset (start point)

U Slope

Uw Active voltage range (Ys changes)

* When the mechanical limitation of the angle of rotation

and self-adapt function are ON, 100% does not equal

90°. Also valid for control signal 0 to 10 Vdc.

Setting for

10V slope

0 Vdc offset

Figure 11.

Table 2.

Examples in Figure 10

Offset

Vdc

U

Slope

Vdc

Active Voltage

Range

Vdc

Actuator

Position

1. Minimum slope

0 to 2

0 to 100%

2. Limitation of rotation

5 to 10

0 to 16.7%

3. Limitation of rotation

0 to 10

0 to 33.3%

4. Setting shown in Figure

11.

0 to 10

0 to 100%

Control signal

adjustment

example:

Determine the setting needed to electronically limit the angle of rotation between 0 to 50%

(0° to 45°) using a 2 to 10 Vdc input.

Calculating the value of U:

VdcVdcVdcVdcUoVdc

[%]

U16)210(

%50 %100

])[][10(

[%]Ysrotationof

angleworking

100 

Settings: Uo = 2 Vdc;

U = 16 Vdc

Electronic limitation

angle of rotation Ys = 50% (45°)

Slope U = 16V

Active voltage range Uw = 2 to 10 Vdc

Figure 12. Example.

Technical Instructions OpenAir® GDE Enhanced Non-Spring Return Rotary Electronic Damper Actuator

Document Number 155-784

October 20, 2016

Page 8 Siemens Industry, Inc.

Auxiliary Switches

GDE146.1P, GDE346.1U, GDE164.1P, GDE166.1P

Figure 13 shows the adjustable switching values for Auxiliary Switches A and B.

Actuator Scale:

Clockwise

Adjustment range for

Switches A and B

Setting interval: 5°

Switching hysteresis: 2°

Actuator Scale:

Counterclockwise

Figure 13. Adjustable Switching Values

for the Dual Auxiliary Switches.

NOTE: The auxiliary switch setting shafts rotate with the actuator. The scale is valid only

when the actuator is in the 0 position on clockwise motion.

Use the long arm of the †(AUX SWITCHADJUSTMENT) to point to the position of Switch A. Use

the narrower tab on the red ring to point to the position of Switch B.

Rotation Direction

GDE14x.1P, GDE34x.1U

Two-position/Floating

Control

Figure 14. Setting the Rotation Direction.

OpenAir® GDE Enhanced Non-Spring Return Rotary Electric Damper Actuator Technical Instructions

Document Number 155-784

October 20, 2016

Siemens Industry, Inc. Page 9

Rotation Direction

Switch

Counterclockwise Clockwise

Figure 15. Direction of Rotation Switch.

The factory setting is clockwise.

The direction of rotation switch should match the damper rotation movement.

Dual in-Line Package

(DIP) Switches

GDE16x.1P

Raise the protective cover from left to right to locate the DIP switches. See

Figure 9 for the location of the cover.

Modulating

control signal selection

Figure 16.

0 to 10 Vdc

Position

(Factory Setting).

To change the control signal from the factory setting (0 to

10 Vdc), move the first DIP switch to the UP (2-10)

position.

Self-adapt Switch

Figure 17.

OFF Position

(Factory Setting).

The factory setting is 0(OFF).

When mechanical angle of rotation is limited, the self-adapt

switch (middle DIP switch) may be turned ON so that the

limited range will become the new 0 to 100% for the

actuator logic. In this case, 0 to 100% is not equal to 90°

CAUTION:

When turning the self-adaptive feature on or

after the software reset with the feature on, the

actuator will enter a five-minute calibration

cycle as the actuator adjusts to the rotation

limits of the system. A software reset happens

after power on or may be caused by

electrostatic discharge (ESD) at levels of 2kV

and above.

The self-adapt capability will scale the control signal

selected, either a 0 to10 Vdc or a 2 to 10 Vdc signal, within

the adjusted mechanical range. The feedback signal will

also reflect the control signal selected, either a 0 to 10 Vdc

or a 2 to 10 Vdc.

Technical Instructions OpenAir® GDE Enhanced Non-Spring Return Rotary Electronic Damper Actuator

Document Number 155-784

October 20, 2016

Page 10 Siemens Industry, Inc.

Sizing

The type of actuator required depends on several factors.

1. Obtain damper torque ratings (ft-lb/ft2or Nm/m2) from the damper

manufacturer.

2. Determine the area of the damper.

3. Calculate the total torque required to move the damper:

Total Torque =

SF eaDamper AringTorque Rat 1



1Safety Factor: When determining the torque of an actuator required,

a safety factor should be included for unaccountable variables such as

slight misalignments, aging of the damper, and so on. A suggested

safety factor is 0.80 (or 80% of the rated torque).

4. Select the non-spring return actuator type from Table 3.

Table 3.

Total Torque

Actuator

<44 lb-in (5 Nm)

GDE

<88 lb-in (10 Nm)

GLB

<132 lb-in (15 Nm)

GEB

<221 lb-in (25 Nm)

GBB

<310 lb-in (35 Nm)

GIB

>310 lb-in >620 lb-in

(35 Nm to 70 Nm)

Use tandem mounting bracket ASK73.1 with

any GIB1x actuator.

Mounting and

Installation

Place the actuator on the damper shaft so that the front of the actuator is

accessible. The label is on the front side. A mounting bracket is included with the

actuator.

The minimum damper drive shaft length is 3/4-inch (20 mm).

Observe the service envelope around the actuator as shown in Figure 31.

Detailed mounting instructions are included with each actuator.

1/2-inch Ø

Factory-Installed

Guide

3/8-inch Ø

Use the shaft insert supplied for any

3/8-inch (8 to 10mm) diameter shaft

5/8-inch Ø

Figure 18. Damper Shaft Sizes.

NOTE: For all damper shafts with the exception of the 1/2-inch round shaft: Remove

1/2-inch Ø factory-installed guide before installation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens SINAMICS S120 Kurzanleitung

Siemens

Siemens SITRANS LUT400 Benutzerhandbuch

Siemens

Siemens SIMATIC S5-115U Bedienungsanleitung

Siemens

Siemens N526E02 Bedienungsanleitung

Siemens

Siemens REA23M Bedienungsanleitung

Siemens

Siemens Simatic S7-400 Bedienungsanleitung

Siemens

Siemens Acvatix SSC31 Bedienungsanleitung

Siemens

Siemens HiPath C10 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Betriebsanleitung

Siemens

Siemens SSC161.05U Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Bedienungsanleitung

Siemens

Siemens S7-1200 TELECONTROL Bedienungsanleitung

Siemens

Siemens scalance WLC711 Administratorhandbuch

Siemens

Siemens REV23.03RF Bedienungsanleitung

Siemens

Siemens 540-103 Bedienungsanleitung

Siemens

Siemens SSD161S.05DU Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Montageanleitung

Siemens

Siemens Flowrite 599 Series Betriebsanleitung

Siemens

Siemens RVL482 Bedienungsanleitung

Siemens

Siemens POL220 Series Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Siemens

Siemens DE406M Series Bedienungsanleitung

Siemens

Siemens Powermite 599 MT Series Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung