Siemens Powermite 599 MT Series Betriebsanleitung

Powermite 599

Technical Instructions

Document No. 155-314P25

EA 599-16

August 1, 2007

MT Series SSC Electronic

Valve Actuator, 24 Vac

Floating Control (3-Position)

EA1157R1

Siemens Building Technologies, Inc.

Description The Powermite 599 MT Series SSC81U and SSC81.5U electronic valve actuators

require a 24 Vac supply to provide a floating control signal. These actuators control

Powermite 599 MT Series valves with a 7/32-inch (5.5 mm) stroke and a threaded

valve bonnet that fits the actuators.

Features •UL listed for plenum installations

•Direct-coupled installation without special tools (hand-tightened)

•Manual override

•Visual position indication

Application The Powermite 599 Series MT Series SSC81 electronic actuators and MT Series

valves are used in heating and cooling applications. They are used in liquid and steam

applications that require an actuator. The SSC81 series accepts plenum cable or 3/8-

inch flex conduit connection.

Product Numbers Table 1. Product Numbers.

Actuator Operating Mode

Actuator Prefix

Code

SSC81U Non-Spring Return

(Fail-in-Place) 259

SSC81.5U Spring Return

(Fail-Safe) 260

Ordering a Valve

Plus Actuator

Assembly

To order a complete valve plus actuator assembly from the factory, combine the

actuator prefix code with the suffix of the valve product number. See Technical Bulletin

TB251, Powermite 599 Series MT Series Terminal Unit Valve and Actuator Assembly

Selection (155-306P25) for selection procedures.

To order an actuator only, use the product number.

Technical Instructions MT Series SSC Electronic Valve Actuator, 24 Vac Floating (3-Position) Control

Document Number 155-314P25

August 1, 2007

Page 2 Siemens Building Technologies, Inc.

Specifications

Power requirements

Operating voltage 24 Vac ±20%

Frequency 50/60 Hz ±2 Hz

Power supply Earth ground isolating, Class 2,

24 Vac transformer

NOTE: Do not power more than

10 actuators with one

transformer.

SSC81U power consumption 0.8 VA

SSC81.5U power consumption 3 VA at ultra cap load,

2 VA at normal operation

Control characteristic Control Signal

Y2 Retracts actuator shaft

Y1 Extends actuator shaft

G System potential

G0 (SSC81.5U only) System neutral

Functional operation Running time

SSC81U 150 s ±2% at 50 Hz

125 s ±2% at 60 Hz

SSC81.5U 125 s ±2% at 50/60 Hz

Spring return, SSC81.5U only (Figure 1, ) ≈30 s

Nominal stroke 7/32-inch (5.5 mm)

Nominal force 67 lb (300N)

Stroke/signal relationship Linear

Capacitor charge time (Figure 1 ) max. 180 sec

Spring return (SSC81.5U only) Non-mechanical, electronic returns

to stem up (0 position)

Agency certification UL UL873 Listed

cUL Certified to CSA

C22.2 No. 24-93

Ambient conditions Ambient temperature

Operation 41°F to 122°F (5°C to 50°C) with

Transport and storage -13°F to 158°F (-25°C to +70°C)

Ambient humidity 0 to 90% rh (non-condensing)

Media temperature 41°F to 248°F (5°C to 120°C)

Physical characteristics Wiring Connection Plenum cable or 3/8-inch flex conduit

Weight

SSC81U 1.1 lb (0.5 kg)

SSC81.5U 1.3 lb (0.6 kg)

Dimensions 5.5-in × 4.35-in × 2.0-in

(140 mm × 110,6 mm × 48 mm)

MT Series SSC Electronic Valve Actuator, 24 Vac Floating (3-Position) Control Technical Instructions

Document Number 155-314P25

August 1, 2007

Siemens Building Technologies, Inc. Page 3

Service Kits

EA1156R1

EA1162R1

EA0851R1

EA1138R1

411555648 (031215F): Kit contains:

- Terminal cover

- Cover screws-2 (not shown)

- Tailpiece

- Tailpiece screw-1 (not shown)

- Cable lock

- Terminal block-3

EA0850R1

EA0851R1

411656088 (031215F or later): Kit

contains:

- Terminal Cover

- Cable lock

- Cover screw- 1 (not shown)

Operation A 24 Vac control signal to terminal Y1 extends the actuator shaft proportionately to the

length of time the signal is applied.

A 24 Vac control signal to terminal Y2 retracts the actuator shaft proportionately to the

length of time the signal is applied.

In the event of a power failure with no control voltage, the non-spring return SSC81U

will hold its last position.

In the event of a power failure, the SSC81.5U spring returns to the stem up 0 position.

The SSC81.5U includes an electronic return mechanism that functions as follows. See

Figure 1.

•At power-up (t0), a capacitor must

charge to its maximum capacity

(Max, tc). This will take a maximum

of 180 sec, during which time no

actuator movement occurs.

•Once the capacitor is fully charged

(tc), normal actuator operation

occurs.

•If a subsequent power failure occurs

(tn) of greater than 5 seconds, the

capacitor discharges (td) and the

actuator spring returns to stem up 0

position.

EA0798R2

TIME

MAX

180s. MAX

30s.

CHARGE

Max

NORMAL

ACTUATOR

OPERATION

ACTUATOR

POSITION

TIME TO

DISCHARGE

TIME TO

CHARGE

t0 tctntd

Figure 1. SSC81.5U Electronic Spring

Return Mechanism.

Technical Instructions MT Series SSC Electronic Valve Actuator, 24 Vac Floating (3-Position) Control

Document Number 155-314P25

August 1, 2007

Page 4 Siemens Building Technologies, Inc.

Operation, Continued

CAUTION:

A valve must be connected to the actuator before applying power.

If applying power to the actuator when a valve is not connected, the

actuator will respond to a control signal and the shaft will extend until it

reaches its maximum end stop. Thereafter, it will not respond to any

signal. If this occurs:

1. Disconnect power.

2. Turn the manual position indicator (See Figure 7 and Figure 8)on

the top of the actuator to the 0 position and verify the actuator

shaft completely retracts.

3. Connect a valve to the actuator, reapply power. The actuator will

return to normal operation.

Calibration Stroke The SSC81.5U writes its calibration stroke parameters to nonvolatile memory on the

first startup of the actuator. Successive startups bypass the calibration stroke unless the

memory is manually cleared. If installing the actuator on a different valve (such as on a

replacement valve), manually clear the calibration stroke from memory as follows:

1. Remove the terminal cover using a Phillips

head screwdriver.

2. Locate hole on the circuit board shorting

bars.

3. Insert and gently twist a flat-blade

screwdriver to electrically connect the

shorting bars (Figure 2). The SSC81…

then performs a new calibration stroke.

4. Secure the terminal cover back in place.

EA1155R1

WIRING TERMINAL

WITH REMOVABLE

TERMINAL BLOCK

Shorting

Bars

TERMINAL

COVER

AND SCREWS

Figure 2. Manually Clearing Calibration

Stroke from Memory.

Mounting and

Installation Mount the actuator in one of the allowable positions shown in Figure 3.

EA0791R2

Figure 3. Mounting Position.

When mounting the actuator in a plenum, the proper cable must be attached to meet

local codes. Allow 8 inches (200 mm) above the actuator and 8 inches (200 mm) behind

the cable for service.

MT Series SSC Electronic Valve Actuator, 24 Vac Floating (3-Position) Control Technical Instructions

Document Number 155-314P25

August 1, 2007

Siemens Building Technologies, Inc. Page 5

Wiring Use earth ground isolating, step-down Class 2 transformers. Do not use

autotransformers.

Determine supply transformer rating by summing total VA of all actuators used. The

maximum rating for a Class 2 step-down transformer is 100 VA.

Do not power more than 10 actuators by one transformer.

CAUTION:

Terminals must be properly wired for correct function and full life of the

actuator.

Wiring Diagrams

NEUT

CONTROLLER ACTUATOR

EARTH GROUND

ISOLATING CLASS 2

TRANSFORMER FOR

24 Vac POWER

120 Vac

Vac

EA0795R1

Y2…Retracts actuator shaft

Y1…Extends actuator shaft

G System potential

Figure 4. SSC81U Non-Spring Return.

EA1234R1

NEUT

CONTROLLER

EARTH GROUND

ISOLATING CLASS 2

24 Vac TRANSFORMER

120 Vac

24 Vac

ACTUATOR

Y2…Retracts actuator shaft

Y1…Extends actuator shaft

G… System potential

G0…System neutral

Figure 5. SSC81.5U SR Neutral.

EA1235R1

NEUT

CONTROLLER

EARTH GROUND

ISOLATING CLASS 2

24 Vac TRANSFORMER

120 Vac

24 Vac

ACTUATOR

Y2…Retracts actuator shaft

Y1…Extends actuator shaft

G… System potential

G0…System neutral

Figure 6. SSC81.5U SR Hot Switch

Technical Instructions MT Series SSC Electronic Valve Actuator, 24 Vac Floating (3-Position) Control

Document Number 155-314P25

August 1, 2007

Page 6 Siemens Building Technologies, Inc.

Manual Override For manual positioning, the override knob

is in the center of the position indicator.

See Figure 7.

CLOCKWISE

EXTENDS

SHAFT

COUNTER

CLOCKWISE

RETRACTS

SHAFT

EA1161R1

Figure 7. Manual Override.

Start-up Check the wiring and the position indicator

(Figure 8).

Position Indicator Output Shaft

0 Retracted

1 Extended

EA1158R1

Figure 8. Position Indicator

(Shown in 0 Position).

Troubleshooting Check the wiring for proper connections.

Service Kits If the actuator is inoperative, replace the unit.

MT Series SSC Electronic Valve Actuator, 24 Vac Floating (3-Position) Control Technical Instructions

Document Number 155-314P25

August 1, 2007

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as

design improvements are introduced. Flowrite is a trademark of Siemens Building Technologies, Inc. Product or company names mentioned herein

Siemens Building Technologies, Inc.

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

U.S.A.

Your feedback is important to us. If you have comments

about this document, please send them to

[email protected]

Document No. 155-31425

Country of Origin: US

Page 7

Dimensions

(48)

4.4

(110,8)

3.5

(89)

.85

(21,6)

4.5

(115,1) 5.5

(140)

EA1159R1

Figure 9. SSC Actuator Dimensions in Inches (Millimeters).

Service envelope Minimum access space recommended:

8 inches (200 mm) above the actuator and 8 inches (200 mm) beside the terminal

cover.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens RMZ791 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Installationsanleitung

Siemens

Siemens S7-1200 TELECONTROL Bedienungsanleitung

Siemens

Siemens Synco 700 Bedienungsanleitung

Siemens

Siemens GAMMA instabus UP 204 Service-Handbuch

Siemens

Siemens RWF40 Series Kurzanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens RWF40 Series Bedienungsanleitung

Siemens

Siemens LMV37.4 Series Bedienerhandbuch

Siemens

Siemens RMG 508SE Bedienungsanleitung

Siemens

Siemens SITRANS LUT400 Bedienungsanleitung

Siemens

Siemens Climatix S300 HRV Benutzerhandbuch

Siemens

Siemens RVP201 Bedienerhandbuch

Siemens

Siemens SINUMERIK 810DE Technisches Dokument

Siemens

Siemens SIMOTION C230-2 Bedienungsanleitung

Siemens

Siemens SIMATIC S5-100U Benutzerhandbuch

Siemens

Siemens Acvatix SSC31 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RM1 Bedienungsanleitung

Siemens

Siemens RVD230 Bedienerhandbuch

Siemens

Siemens GBB 2 Series Bedienungsanleitung

Siemens

Siemens BACnet ATEC Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA142 8XC21 Sries Bedienungsanleitung

Siemens

Siemens SITOP PSU8600 Bedienungsanleitung

Siemens

Siemens scalance WLC711 Administratorhandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung