Siemens RMG 508SE Bedienungsanleitung

CONTROL BOX RMG 508SE

3001138

2894

The new RMG 508SE control box, fitted with the reset button extension, replaces control box 508SE, but

does not replace the old 505SE version.

Control box RMG 508SE does not have a delay time between the second stage (terminal 14) and third

stage (terminal 11), as shown on the control box’s diagram under the cover - consequently, you will need to

check the burner for malfunctions.

RESETTING THE CONTROL BOX AND USING DIAGNOSTICS

The control box features a diagnostics function through which any causes of malfunctioning are easily iden-

tified (indicator:

RED LED

To use this function, you must wait at least 10 seconds once it has entered the safety condition (

lock-out

and then press the reset button.

The control box generates a sequence of pulses (1 second apart), which is repeated at constant 3-second

intervals.

Once you have seen how many times the light pulses and identified the possible cause, the system must

be reset by holding the button down for between 1 and 3 seconds.

The methods that can be used to reset the control box and use diagnostics are given below.

RESETTING THE CONTROL BOX

To reset the control box, proceed as follows:

➣

Hold the button down for between 1 and 3 seconds.

The burner restarts after a 2-second pause once the button is released.

If the burner does not restart, you must make sure the limit thermostat is closed.

VISUAL DIAGNOSTICS

Indicates the type of burner malfunction causing lock-out.

To view diagnostics, proceed as follows:

➣

Hold the button down for more than 3 seconds once the red LED (burner lock-out) remains steadily lit.

A yellow light pulses to tell you the operation is done.

Release the button once the light pulses. The number of times it pulses tells you the cause of the mal-

function, indicated in the table below.

Once the operations are done, the control box’s initial state must be restored using the resetting procedure

described above.

BUTTON PRESSED FOR CONTROL BOX STATUS

Between 1 and 3 seconds Control box reset without viewing visual diagnostics.

More than 3 seconds Visual diagnostics of lock-out condition:

(LED pulses at 1-second intervals).

ATTENTION

THIS OPERATION MUST BE CARRIED OUT BY A QUALIFIED TECHNICIAN

=== = = = = = = =

Press reset

for >3s 3sPulses Pulses

RED LED on

wait at least 10s Interval

Lock-out

2894

The sequence of pulses issued by the control box identifies the possible types of malfunction, which are

listed in the table below.

SIGNAL PROBABLE CAUSE

2 pulses

The flame does not stabilise at the end of the safety time:

– faulty ionisation probe;

– faulty or soiled gas valves;

– neutral/phase exchange;

– faulty ignition transformer

– poor burner regulation (insufficient gas).

3 pulses

===

Min. air pressure switch does not close:

– air pressure switch faulty;

– air pressure switch incorrectly regulated;

– max. air pressure switch triggered (if installed).

4 pulses

====

Min. air pressure switch does not open or light in the chamber before firing:

– air pressure switch faulty;

– air pressure switch incorrectly regulated.

7 pulses

=======

Loss of flame during operations:

– poor burner regulation (insufficient gas);

– faulty or soiled gas valves;

– short circuit between ionisation probe and earth.

10 pulses

=====

– Wiring error or internal fault.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens SIRIUS 3RW44 Bedienungsanleitung

Siemens

Siemens SSD31 Series Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Bedienungsanleitung

Siemens

Siemens RVA63.280 Bedienerhandbuch

Siemens

Siemens sinamics dcp Bedienungsanleitung

Siemens

Siemens SIRIUS 3RF29.0-0KA 0KH0 Series Bedienungsanleitung

Siemens

Siemens SQD Series Bedienungsanleitung

Siemens

Siemens 353 Bedienungsanleitung

Siemens

Siemens GD Series Bedienungsanleitung

Siemens

Siemens RVP200 Bedienungsanleitung

Siemens

Siemens SIRIUS ET 200S Bedienungsanleitung

Siemens

Siemens N 523/11 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500/ET 200MP Benutzerhandbuch

Siemens

Siemens LME7 Series Bedienerhandbuch

Siemens

Siemens instabus JB526C23 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Installationsanleitung

Siemens

Siemens N 543D31 Bedienungsanleitung

Siemens

Siemens RLU2 Series Bedienungsanleitung

Siemens

Siemens SIRIUS 3RW44 Bedienungsanleitung

Siemens

Siemens SIMATIC S5-115F Bedienungsanleitung

Siemens

Siemens 353 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens Flowrite 599 Series Betriebsanleitung

Siemens

Siemens Desigo RXC32.1 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung