Siemens RDX33.21 Bedienungsanleitung

N3075en

17.04.2009 Building Technologies

3075

RDX33.21, RDX43.2

Room temperature

controllers with LCD and

7-day time switch

RDX33..

RDX43..

For release of a heat pump or control of actuating devices

in heating or cooling mode

•Operating modes: Auto Timer, Comfort, Energy Saving, and Protection

•Potential-free output (ON / OFF) for release of a heat pump or control of

actuating devices

•Potential-free output (ON / OFF) for selection of heating or cooling

•Output for control of auxiliary electric heating (RDX43.2)

•Manual heating / cooling changeover

•8 programmable time switches

•Selectable commissioning and control parameters

•Selectable display of room temperature or setpoint

•Minimum and maximum setpoint limitation

•Operating voltage: Batteries DC 3 V (RDX33.21)

AC 230 V (RDX43.2)

2/14

Siemens Room temperature controller with LCD N3075en

Building Technologies 17.04.2009

Use

For control of the room temperature in individual rooms or zones that are heated or

cooled by a heat pump or via actuating devices.

The room temperature controller…

•controls release of the heat pump’s compressor or actuating devices

•switches an auxiliary electric heater

Suited for systems with manual H/C changeover.

Functions

•Manual H/C changeover by pressing the respective button

•Room temperature control with built-in sensor

•

Selection of operating mode via button

•Auto Timer mode with 8 programmable time switches for changeover between Com-

fort mode and Energy Saving mode

•Outputs for release of heat pump and for control of actuating devices in heating or

cooling mode (ON / OFF). Output for auxiliary electric heater

Controller

The controller acquires the room temperature via its built-in sensor and maintains it at

the adjusted setpoint.

The switching differential is 2 K in heating mode and 1 K in cooling mode (adjustable

via parameters P08 and P09).

The display shows the acquired room temperature or the setpoint of the current operat-

ing mode. This can be selected via parameter P15. Factory setting is display of the

current room temperature.

The heating and cooling symbols on the display show the system’s operating

state. Symbol shows when the auxiliary electric heater is in operation.

Symbol cindicates when the heat pump’s compressor is on.

If required, room temperature and setpoint can also be displayed in °F in place of °C.

This is made by changing parameter P14.

Operating modes

The following operating modes are available by pressing the respective button:

In Auto Timer mode AUTO, the controller switches automatically between Comfort mode

and Energy Saving mode according to the 8 programmed time switches. The controller

displays the symbol of Auto Timer mode AUTO and that of the current operating mode,

either Comfort mode or Energy Saving mode .

In Comfort mode , the controller maintains the setpoint, which can be adjusted via the

buttons.

For energy saving purposes, the setpoint setting range can be limited to a minimum

(parameter P05) and a maximum (parameter P06).

Temperatue control

Display

Auto Timer mode

Comfort mode

Energy saving tip

Setpoint limitation

3/14

Siemens Room temperature controllers with LCD N3075en

Building Technologies 17.04.2009

•If the minimum limit P05 is set lower than the maximum limit P06, both heating and

cooling are adjustable between these 2 limits.

•For heating or cooling applications:

– The setting range in cooling mode is from P05…40 °C instead of 5…40 °C

– The setting range in heating mode is from 5…P06 °C instead of 5…40 °C

Examples Heating or cooling

P05 < P06

5°C 40°C25°C18°C

P06P05

Cooling setpoint adjustable 18…25 °C

Heating setpoint adjustable 18…25 °C

P05 ≥P06

5°C 40°C25°C21°C

P05P06

Cooling setpoint adjustable 25…40 °C

Heating setpoint adjustable 5…21 °C

The setpoints for Energy Saving mode can be adjusted via control parameters P01

and P02.

In Protection mode , the controller monitors the setpoints adjusted for heating and

cooling. If the room temperature exceeds or falls below the setpoint, the setpoint for

Protection is maintained (this independent of the manual H/C changeover status).

These setpoints can be adjusted via control parameters P03 and P04. The factory set-

ting for heating in Protection mode is 8 °C.

P05 < P06

P05 ≥P06

Energy Saving mode

Protection mode

4/14

Siemens Room temperature controller with LCD N3075en

Building Technologies 17.04.2009

Control sequences

On Q33-Q34 Q13-Q14

On Q13-Q14

= =

Application with heat pump for heating or cooling

W Room temperature setpoint

WD Switching differential between heating and auxiliary electric heating

SDH Switching differential heating

SDC Switching differential cooling

When used in connection with a heat pump, output Q13-Q14 (NO contact) must be

connected to the compressor’s control input.

Output Q21-Q22-Q24 must be connected to the compressor’s H/C control input.

Output Q33-Q34 (NO contact) is for connection to an auxiliary electric heater

(RDX43.2).

Button is used for manual changeover from heating to cooling, or vice versa. The

factory setting of the changeover contact is “Open“ for heating and can be changed to

”Closed” for heating using parameter P18.

To avoid damage to the compressor during H/C changeover, a minimum compressor

on / off time can be adjusted via parameters P11 and P12. The factory setting for the

minimum on time is 1 minute and for the minimum off time 3 minutes.

Legend

Heating / cooling mode

Compressor on time

5/14

Siemens Room temperature controllers with LCD N3075en

Building Technologies 17.04.2009

Output Q33-Q34 is for connection to the auxiliary electric heater which is only available

in heating mode, provided parameter P16 is set to 1 (enable). The minimum on time

can be changed via parameter P13 (factory setting is 1 minute).

Auto Timer mode

The controller provides an Auto Timer mode with 8 programmable time switches. Each

time switch can be assigned one or several days. In this mode, the controller switches

automatically between Comfort mode and Energy Saving mode according to the pro-

grammed time switches.

Auto timer in Comfort mode Auto timer in Energy Saving mode

Each time switch has a start time and end time for Comfort mode which can be applied

to several weekdays.

To set the time schedule, keep button depressed for 3 seconds to go to the pro-

grammable timer setting mode. This mode is indicated by displaying Ax (x = auto timer

1...8) and the time of day --:-- blinking.

For each time switch, proceed as follows:

1. Symbols and are displayed. Press or to set the Comfort mode start time

and confirm by pressing .

2. Symbols and are displayed. Press or to set the start time for Comfort

mode or Energy Saving mode and confirm by pressing .

3. Symbol

1will flash. Press to select or to deselect each day and advance to

the next day. Confirm setting for actual timer by pressing and advance to

the next timer.

The controller leaves the programmable time switch setting mode if no button is

pressed within 20 seconds. All changes made after the last press of will not be

saved.

Auxiliary electric heater

RDX43.2

Setting the time

switches

6/14

Siemens Room temperature controller with LCD N3075en

Building Technologies 17.04.2009

Press to sequentially review the 8 time switches.

Time switches A1…A4 have the following factory settings:

Day(s) Times of day when controller is in Comfort mode

Mo (1) – Fr (5) 06:30 – 08:30 (A1) 17:30 – 22:30 (A2)

Sa (6) 08:00 – 23:00 (A3)

So (7) 08:00 – 22:30 (A4)

- During remaining times, controller is in Energy Saving mode

- Time switches A5…A8 are free (no factory settings made)

The settings of the time switches can be changed to suit individual needs. The factory

settings can be retrieved any time:

1. Set the controller to Protection mode .

2. Press and simultaneously for 3 seconds. Release the buttons and, within 2

seconds, press 2 times.

The display shows “8888“ during this process.

In the second case, or when several time switch sequences overlap, the resulting out-

put is the OR combination of the Comfort mode time of all time switches.

The 7-day

time

switch

supports

the 12-

hour and

24-hour

format.

Parameter P17 = 0 (12 h) or = 1 (24 = factory setting).

1. Keep the button depressed until the time digits start blinking.

Press or to set the time of day.

2. Confirm the time of day by pressing and the weekday indicator starts blinking.

3. Press or to set the current weekday.

4. Confirm by pressing .

In the event of a power failure, the time, date, last operating mode, last heating/cooling

changeover status, setpoint and auto timer program will be stored. When power re-

turns, this time reappears and starts running again. The time display blinks to indicate

that there was a power failure. Blinking stops when the time and the day are confirmed

by pressing , or when the time is readjusted by following the above procedure.

Replace / remove battery when the “low battery” symbol is activated. The time, date,

last operating mode, last heating/cooling changeover status, setpoint and auto timer

program will be stored.

Error handling

If the room temperature is out of the measuring range (above 50 °C or below 0°C), the

display shows the limiting temperature in blinking figures (e.g. 50 °C or 0 °C).

Should the built-in sensor become defective, the display will show “Err” blinking to draw

the user‘s attention.

Viewing the time

switches

Factory settings of

time switches

Retrieving the factory

settings

Overlapping of time

switch sequences

7-day time switch

Setting the clock

Power failure

Symbol “low battery”

Temperature out of

measuring range

Failure of built-in

sensor

A1=09:00-22:00

A2=12:00-20:00

09:00 12:00 20:00 22:00

Resulting output

= 09:00-22:00

7/14

Siemens Room temperature controllers with LCD N3075en

Building Technologies 17.04.2009

Control parameters

A number of control parameters can be readjusted to optimize the control performance.

These parameters can also be set during operation without opening the unit. In the

event of power failure, all control parameter settings will be maintained.

The parameters can be changed as follows:

1. Set the controller to Protection mode .

2. Press and simultaneously for 3 seconds. Release the buttons and, within

2 seconds, press again for 3 seconds. The display will show “P01“.

3. Select the required parameter by repeatedly pressing and .

P01 P02 P18

3075Z03

4. By pressing and simultaneously, or by pressing , the current value of

the selected parameter appears, which can be changed by repeatedly pressing

or .

5. 5 seconds after the last press of a button, or by pressing and simultane-

ously, the value will be stored.

6. If you wish to display and change additional parameters, repeat steps 3

through 5.

7. 10 seconds after the last display or setting, all changes will be stored and the

controller returns to Protection mode.

The factory setting of the control parameters can be retrieved as follows:

1. Set the controller to Protection mode .

2. Press and simultaneously for 3 seconds.

Release the buttons and, within 2 seconds, press the

operating mode button 2 times.

The display shows “8888“ during this process.

Parameter settings

Parameter reset

8/14

Siemens Room temperature controller with LCD N3075en

Building Technologies 17.04.2009

Parameter Factory setting Setting range in increments of ..K/..min RDX33 RDX43

P01 Setpoint for heating in Energy Saving mode (W heat Eco) 16 OFF, 5 °C…W cool Eco, 0.5 K

P02 Setpoint for cooling in Energy Saving mode (W cool Eco) 28 OFF, W heat Eco…40 °C, 0.5 K

P03* Setpoint for heating in Protection mode (W heat PROT.) 8 °C OFF, 5 °C…W cool PROT.,0.5 K

P04* Setpoint for cooling in Protection mode (W cool PROT.) OFF OFF, W heat PROT. …40 °C, 0.5 K

P05 Min. setpoint limitation in Comfort mode (W min Comf.) 5 °C 5…40 °C, 0,5 K

P06 Max. setpoint limitation in Comfort mode (W max Comf.) 35 °C 5…40 °C, 0.5 K

P07 Sensor calibration 0 K -3…+3 K, 0.5 K

P08 Switching differential in heating mode SDH 2 K 0.5…+4 K, 0.5 K

P09 Switching differential in cooling mode SDC 1 K 0.5…+4 K, 0.5 K

P10 Setpoint differential between heating and auxiliary heating WD2 K 0.5…+5 K, 0.5 K X

P11 Min. compressor on time (Q14) 1 min. 1…10 minutes, 1 min.

P12 Min. compressor off time (Q14) 3 min. 1…10 minutes, 1 min.

P13 Min. hold time of auxiliary heating 1 min. 1…10 minutes, 1 min. X

P14 Selection of °C or °F °C C or °F

P15 Display of room temperature or setpoint ON OFF: Setpoint

ON: Room temperature

P16 Auxiliary heating in heating mode 1: Enable 0: Disable

1: Enable X

P17 12- or 24-hour format 1: 24 h 0: 12-hour format

1: 24-hour format

P18 Acting direction of H/C changeover signal Q21-Q22 0: 0: Open (heating), closed (cooling)

1: Closed (heating), open (cooling)

P03*/P04*: P04 is at least min. 5 K higher than P03 X Not available

Type summary

Product No. Features

RDX33.21 Room temperature controller with outputs for compressor and H/C

changeover, operating voltage DC 3 V (battery-powered)

RDX43.2 Room temperature controller with outputs for compressor, H/C

changeover and auxiliary electric heating, operating voltage AC 230 V

Equipment combinations

Description Product No. Data Sheet

Electromotoric 2-position valve with actuator MVI…/MXI… 4867

Electromotoric 2-position actuator SFA21... 4863

Thermal actuator (for TRVs) STA21... 4893

Thermal actuator (for small valves 2.5 mm) STP21... 4878

Control parameters for RDX33.21 and RDX43.2

9/14

Siemens Room temperature controllers with LCD N3075en

Building Technologies 17.04.2009

Accessories

Description Product No.

Adapter plate 120 x 120 mm for recessed conduit boxes 4“ x 4“ ARG70

Adapter plate 96 x 120 mm for recessed conduit boxes 2“ x 4“ ARG70.1

Adapter plate 112 x 130 mm for surface wiring ARG70.2

Ordering

When ordering, please give description and product No.:

E.g. room temperature controller RDX33.21

Valve actuators are to be ordered as separate items.

Mechanical design

The controller consists of 2 parts:

•Plastic housing which accommodates the electronics, the operating elements and the

built-in room temperature sensor

•Mounting base

The housing engages in the mounting base and snaps on.

The base carries the screw terminals.

10/14

Siemens Room temperature controller with LCD N3075en

Building Technologies 17.04.2009

1.5V

'AA'

1.5V

'AA'

Operating elements

1 Buttons + and - for adjusting the setpoints, the control parameters, the days of

week, and the time of day

2 Button for selecting the mode of operation:

Protection mode

Comfort mode

Energy Saving mode

AUTO Auto Timer mode

3 Button for manual H/C changeover

4 Button for time of day and weekday settings in automatic time switch program

5 Button for selecting and setting the 8 time switches

6 Button for confirmation

Display

7 Day of week 1...7 (1 = Monday / 7 = Sunday)

8 Current room temperature, room temperature setpoint in °C or °F

9 Cooling mode

10 Auxiliary electric heating ON

11 cCompressor ON

12 Symbol for display of current room temperature

13 Time of day in hours and minutes (12- or 24-hour format)

14 Symbols:

Battery exchange

Protection mode

Comfort mode

Energy Saving mode

AUTO Auto Timer mode

15 Battery compartment (only with RDX33.21)

Setting elements,

operating elements

and display

Legend

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens RVL481 Bedienerhandbuch

Siemens

Siemens RWD32S Bedienungsanleitung

Siemens

Siemens SIMOTION C230-2 Technisches Dokument

Siemens

Siemens GLB111.9E/MO Bedienungsanleitung

Siemens

Siemens 7SR224 Gebrauchs- und Pflegehandbuch

Siemens

Siemens PXC Compact Series Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Stücklistenhandbuch

Siemens

Siemens BT300 LonWorks Gebrauchsanweisung

Siemens

Siemens RUGGEDCOM WIN5214 Bedienungsanleitung

Siemens

Siemens POS8.4420/109 Bedienungsanleitung

Siemens

Siemens SINUMERIK 828D Turning Bedienungsanleitung

Siemens

Siemens Acvatix SAX Series Bedienerhandbuch

Siemens

Siemens DXR2.E10PL-102BK Bedienungsanleitung

Siemens

Siemens ERTEC 200P-2 Bedienungsanleitung

Siemens

Siemens SIMATIC S5-90U Benutzerhandbuch

Siemens

Siemens SSA911.01TH Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens MT Series Betriebsanleitung

Siemens

Siemens SIMATIC S7-200 Benutzerhandbuch

Siemens

Siemens 81000 series Bedienungsanleitung

Siemens

Siemens Desigo PXC4.E16 Bedienungsanleitung

Siemens

Siemens RAJA+ Betriebsanleitung

Siemens

Siemens MEC 1100 Bedienungsanleitung

Siemens

Siemens SSA911.01TH Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung