Siemens SQD Series Bedienungsanleitung
Installation Instructions
Document No. 129-553
December 22, 2011
SQD Series Valve Actuators
(For use with 1-1/2-inch to 2-inch Pressure Independent
Control Valves)
Item Number: 129-553, Rev. AA Page 1 of 4
Product Description
The SQD Actuator requires a 24 Volt power supply
and a 0 to 10Vdc or floating signal to control the
Siemens 1-1/2 inch and 2-inch 599 Series Pressure
Independent Control Valves with 1/4-inch (6.5 mm)
stroke.
Warning/Caution Notations
WARNING: Personal injury/loss of life may
occur if you do not perform a
procedure as specified.
CAUTION: Equipment damage may occur
if you do not perform a
procedure as specified.
Product Number
Description Actuator
Code
SQD65U 0 to 10 Vdc control 235
SQD85.03U 3-position (floating) control 234
Required Tools
•1-1/4-inch open end wrench
•#2 Phillips or flat-blade screwdriver
•Flat-blade calibration screwdriver (3 mm) for
wiring connections
•Wire cutter/stripper
Estimated Installation Time
•15 minutes for wiring a factory-installed
actuator.
•30 minutes for field replacement of actuator.
Prerequisites
WARNING:
If mounting the actuator to a valve
already in line, either close the shut-off
valves in the piping (upstream first,
then downstream) or switch off the
pump to allow the differential pressure
in the valve to drop.
WARNING:
Disconnect the controller power
before replacing the actuator.
90° 90°
EA1326R1
Figure 1. Acceptable Mounting Positions with Valve.
NOTE: Vertical mounting is recommended.
Instructions
If you are mounting an actuator on a new valve, begin
with the instructions, Mounting an Actuator to a Valve.
Remove Actuator from Valve
1. Remove the actuator cover using either a #2
Phillips or a #2 flat blade screwdriver.
See Figure 2.
EA1331R1
M30 x 1.5
1
1
2
1
Figure 2.
2. Disconnect and identify the wires. Place the cover
back on the actuator.
Document No: 129-553
Installation Instructions
December 22, 2011
Remove Actuator from Valve, Continued
3. Use a 1-1/4-inch open end wrench to loosen the
coupling piece.
4. Remove the actuator from the valve.
Mounting an Actuator to a Valve
1. If you are attaching the actuator to a new valve,
remove the protective plastic cap from the valve
stem. See Figure 3.
EA1327R1
VPI45.., VPI45..Q
Figure 3.
2. Turn the manual-positioning knob
counterclockwise to “0”. See Figure 4.
EA1328R1
Figure 4.
3. Place the actuator on the valve. See Figure 5.
EA1329R1
12
Figure 5.
4. Use a 1-1/4-inch open-end wrench to tighten the
coupling piece to a maximum of 22 ft-lbs. See
Figure 6.
EA1330R1
Figure 6.
5. Use either a Phillips head screwdriver or a flat-
blade screwdriver to remove the actuator cover for
access to the terminal block, selector plug, and
jumper wire. See Figure 7.
EA1331R1
M30 x 1.5
1
1
2
1
Figure 7.
6. Attach wires, set the selector plug and if
necessary, cut the R–M jumper. See Wiring.
7. Place the cover on the actuator. The positioning
knob must be at “0” to fit into the shaft. If the cover
does not fit, turn it 180 degrees.
Page 2 of 4 Siemens Industry, Inc.
Document No: 129-553
Installation Instructions
December 22, 2011
8. Fasten the cover with the screws. See Figure 8.
EA1344R1
M30 x 1.5
2
2
1
1
Figure 8.
The installation is now complete.
Wiring
All wiring must conform to NEC and local codes and
regulations.
Use earth ground isolating, step-down Class 2
transformers. Do not use auto transformers.
Determine the supply transformer rating by adding
the total VA of all actuators used. The maximum
rating for Class 2 step-down transformer is 100 VA. It
is recommended that no more than 10 actuators be
powered by one transformer.
SQD65U
To use a 0 to 1000 ohm input signal on terminal R,
the circuit board jumper R—M must be cut.
CAUTION:
If the circuit board jumper R–M is cut, you
cannot wire the R and M terminals on the
terminal block to re-establish the
connection.
The 0 to 1000 ohm signal is additive to the 0 to 10
Vdc control signal. For example, a controller
commanded to 2 Vdc (20%) plus a remote override
input to 300 ohms (30%) results in a position of 50%
stroke.
Figure 9. SQD65U Terminal Connections.
G, G0 24 Vac operating voltage
G System potential
G0 System neutral
Y 0 to 10 Vdc control signal
R Input for 0 to 1000 Ohm remote setting unit or
low temperature detection unit
M Measuring neutral
U Output for 0 to 10 Vdc position indication
WARNING:
Terminal connection G is 24 Vac HOT, not
ground.
CAUTIONS:
•G0 and G must be properly wired for
correct function and full life of the
actuator.
•If the actuator makes a buzzing noise
upon reaching setpoint, G and G0 are
improperly wired and should be
reversed.
SQD85.03U
NEUT
CONTROLLER ACTUATOR
EARTH GROUND
ISOLATING CLASS 2
TRANSFORMER FOR
24 Vac POWER
120 Vac
1
0
Y2
Y1
G
24
Vac
EA0795R1
Figure 10. SQD85.03U Wiring.
G 24 Vac operating voltage (system potential)
Y1 Output shaft extends, valve opens
Y2 Output shaft retracts, valve closes
Siemens Industry, Inc. Page 3 of 4
Document No: 129-553
Installation Instructions
December 22, 2011
Manual Override for SQD65U
Non-Spring Return Troubleshooting
•Check wiring for the proper connections.
•Check selector plug for recommended position.
Turn the manual positioning knob clockwise to move
the actuator stem outward. See •Check for adequate power supply.
Figure 11.
References
Turn the manual positioning knob counterclockwise
to move the actuator stem inward. See Technical Instructions Document Number
Figure 11. SQD Series Electromotoric Actuators 155-777
Pressure Independent Control Series 155-774
Two-Way Brass Valve Bodies,
1/2-Inch to 2-Inch, ANSI 250
Figure 11.
Dimensions
Figure 12. SQD Series Dimensions in Inches (Millimeters).
Minimum access
space recommended
4 inch (100 mm)
8 inch (200 mm)
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models
as design improvements are introduced. Product or company names mentioned herein may be trademarks of their respective owners.
© 2011 Siemens Industry, Inc.
Siemens Industry, Inc.
Building Technologies Division
1000 Deerfield Parkway
Buffalo Grove, IL 60089-4513
USA
1-847-215-1000
Your feedback is important to us. If you have
comments about this document, please
send them to
Document No. 129-553
Printed in the USA
Page 4
Dieses Handbuch passt für folgende Modelle
2
Andere Siemens Controller Handbücher
Siemens
Siemens GIB 1 Series Bedienungsanleitung
Siemens
Siemens LME7 Series Bedienerhandbuch
Siemens
Siemens SIMATIC S7-1200 Benutzerhandbuch
Siemens
Siemens SIRIUS 3RW44 Bedienungsanleitung
Siemens
Siemens SINAMICS V90 PROFINET Benutzerhandbuch
Siemens
Siemens GEB 1 Series Bedienungsanleitung
Siemens
Siemens ATC5300 Bedienungsanleitung
Siemens
Siemens 72G Series Bedienungsanleitung
Siemens
Siemens SIMATIC S5 Bedienungsanleitung
Siemens
Siemens Acvatix SAX Series Bedienerhandbuch
Siemens
Siemens Desigo PXC5.E003 Bedienungsanleitung
Siemens
Siemens GDA Series Bedienungsanleitung
Siemens
Siemens Flowrite 599 Series Bedienungsanleitung
Siemens
Siemens SIMATIC 500 Bedienungsanleitung
Siemens
Siemens SIRIUS 3RF29.0-0KA 0KH0 Series Bedienungsanleitung
Siemens
Siemens SIMOTION P320-4 E Bedienungsanleitung
Siemens
Siemens SIMATIC S7 Betriebsanleitung
Siemens
Siemens ACVATIX G B111.9E/KN Series Bedienungsanleitung
Siemens
Siemens RVD110 Bedienerhandbuch
Siemens
Siemens Gamma instabus UP204 Contouch Service-Handbuch
