Siemens SINAMICS G130 Bedienungsanleitung
Operating instructions · 03/2012
Braking Module / braking resistor
SINAMICS G130
SINAMICS
s
Braking Module / braking resistor
_
_________________
_
_
_________________
_
_
__
_
_______________
_
_________________
_
_
_________________
_
_
_________________
_
SINAMICS
SINAMICS G130
Braking Module / braking resistor
Operating Instructions
Control version V4.5
03/2012
A5E00331454A
Safety information
1
General
2
Mechanical installation
3
Connection
4
Maintenance and servicing
5
Technical specifications
6
Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the relevant information is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E00331454A
Ⓟ 04/2012 Technical data subject to change
Copyright © Siemens AG 2012.
All rights reserved
Braking Module / braking resistor
Operating Instructions, 03/2012, A5E00331454A 3
Table of contents
1 Safety information...................................................................................................................................... 5
1.1 Warnings........................................................................................................................................5
1.2 Safety and application instructions ................................................................................................6
1.3 Components that can be destroyed by electrostatic discharge (ESD) ..........................................7
2 General...................................................................................................................................................... 9
2.1 Braking Module ..............................................................................................................................9
2.2 Braking resistor ............................................................................................................................11
3 Mechanical installation............................................................................................................................. 13
3.1 General ........................................................................................................................................13
3.2 Braking Modules: overview ..........................................................................................................14
3.3 Installing the Braking Module.......................................................................................................17
3.3.1 Installing the Braking Module in a Power Module, frame size FX ...............................................17
3.3.2 Installing the Braking Module in a Power Module frame size GX................................................20
3.3.3 Installing the Braking Module in a Power Module frame size HX................................................23
3.3.4 Installing the Braking Module in a Power Module frame size JX.................................................24
3.4 Installing the braking resistor .......................................................................................................25
4 Connection .............................................................................................................................................. 27
4.1 Cable lugs ....................................................................................................................................28
4.2 Connecting the Braking Module...................................................................................................29
4.3 Connecting the braking resistor ...................................................................................................32
4.4 Disabling the Vdc-max controller .................................................................................................33
5 Maintenance and servicing ...................................................................................................................... 35
6 Technical specifications........................................................................................................................... 37
Table of contents
Braking Module / braking resistor
4 Operating Instructions, 03/2012, A5E00331454A
Braking Module / braking resistor
Operating Instructions, 03/2012, A5E00331454A 5
Safety information 1
1.1 Warnings
WARNING
Hazardous voltages are present when electrical equipment is in operation.
Severe personal injury or substantial material damage may result if these warnings are not
observed.
Only qualified personnel are permitted to work on or around the equipment.
This personnel must be thoroughly familiar with all the warnings and maintenance
procedures described in these operating instructions.
The successful and safe operation of this device is dependent on correct transport, proper
storage and installation, as well as careful operation and maintenance.
National safety guidelines must be observed.
DANGER
Five safety rules
When carrying out any kind of work on electrical devices, the "five safety rules" according to
EN 50110 must always be observed:
1. Disconnect the system.
2. Protect against reconnection.
3. Make sure that the equipment is de-energized.
4. Ground and short-circuit.
5. Cover or enclose adjacent components that are still live.
NOTICE
For a UL-approved system use 60/75°C copper conductors only.
Safety information
1.2 Safety and application instructions
Braking Module / braking resistor
6 Operating Instructions, 03/2012, A5E00331454A
1.2 Safety and application instructions
DANGER
This equipment is used in industrial high-voltage installations. During operation, this
equipment contains live, bare parts. For this reason, they could cause severe injury or
significant material damage if the required covers are removed, if they are used or operated
incorrectly, or have not been properly maintained.
When the machines are used in non-industrial areas, the installation location must be
protected against unauthorized access (protective fencing, appropriate signs).
Prerequisites
Those responsible for protecting the plant must ensure the following:
● The basic planning work for the plant and the transport, assembly, installation,
commissioning, maintenance, and repair work is carried out by qualified personnel and/or
checked by experts responsible.
● The operating manual and machine documentation are always available.
● The technical specifications regarding the applicable installation, connection,
environmental, and operating conditions are always observed.
● The plant-specific assembly and safety guidelines are observed and personal protection
equipment is used.
● Unqualified personnel are forbidden from using these machines and working near them.
This operating manual is intended for qualified personnel and only contain information and
notes relating to the intended purpose of the machines.
The operating manual and machine documentation are written in different languages as
specified in the delivery contracts.
Note
We recommend engaging the support and services of your local Siemens service center for
all planning, installation, commissioning and maintenance work.
Safety information
1.3 Components that can be destroyed by electrostatic discharge (ESD)
Braking Module / braking resistor
Operating Instructions, 03/2012, A5E00331454A 7
1.3 Components that can be destroyed by electrostatic discharge (ESD)
CAUTION
The board contains components that can be destroyed by electrostatic discharge. These
components can be easily destroyed if not handled properly. If you do have to use
electronic boards, however, please observe the following:
•You should only touch electronic boards if absolutely necessary.
•When you touch boards, however, your body must be electrically discharged
beforehand.
•Boards must not come into contact with highly insulating materials (such as plastic
parts, insulated desktops, articles of clothing manufactured from man-made fibers).
•Boards must only be placed on conductive surfaces.
•Boards and components should only be stored and transported in conductive packaging
(such as metalized plastic boxes or metal containers).
•If the packaging material is not conductive, the boards must be wrapped with a
conductive packaging material (such as conductive foam rubber or household aluminum
foil).
The necessary ESD protective measures are clearly illustrated in the following diagram:
● a = conductive floor surface
● b = ESD table
● c = ESD shoes
● d = ESD overall
● e = ESD wristband
● f = cabinet ground connection
● g = contact with conductive flooring
g ga
b
e
d
c
d
a
c
d
b
c a
e
f
f f f f
6LWWLQJ 6WDQGLQJ 6WDQGLQJVLWWLQJ
Figure 1-1 ESD protective measures
Safety information
1.3 Components that can be destroyed by electrostatic discharge (ESD)
Braking Module / braking resistor
8 Operating Instructions, 03/2012, A5E00331454A
Andere Handbücher für SINAMICS G130
33
Inhaltsverzeichnis
Andere Siemens Gleichstromantrieb Handbücher
Siemens
Siemens MICRO MASTER Junior Bedienungsanleitung
Siemens
Siemens SINAMICS SL150 Bedienungsanleitung
Siemens
Siemens SINAMICS SH150 Betriebsanleitung
Siemens
Siemens SINUMERIK 840D sl Betriebsanleitung
Siemens
Siemens SINAMICS DCM Bedienungsanleitung
Siemens
Siemens SINAMICS S120 Bedienungsanleitung
Siemens
Siemens PXC00-PE96.A Bedienungsanleitung
Siemens
Siemens SIMOREG DC-MASTER Bedienungsanleitung
Siemens
Siemens SINAMICS G Datenblatt
Siemens
Siemens SINAMICS GM150 Bedienungsanleitung
Siemens
Siemens 3RV1 Series Bedienungsanleitung
Siemens
Siemens SED2 VFD Installationshandbuch
Siemens
Siemens Simovert 6SE70 Series Bedienungsanleitung
Siemens
Siemens SINAMICS G110D Bedienungsanleitung
Siemens
Siemens SINAMICS G120 Bedienungsanleitung
Siemens
Siemens CP 342-5 Bedienungsanleitung
Siemens
Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung
Siemens
Siemens SINAMICS V20 Series Gebrauchsanweisung
Siemens
Siemens SINAMICS PERFECT HARMONY GH150 6SL3826 Bedienungsanleitung
Siemens
Siemens SINUMERIK 810D Installations- und Betriebshandbuch
Beliebte Gleichstromantrieb Handbücher anderer Marken
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Stücklistenhandbuch
Chamberlain Garog
Chamberlain Garog D Series Bedienungsanleitung
Parker
Parker PDS Series Bedienungsanleitung
Festo
Festo DGC G Series Einrichtungshandbuch
Binks
Binks QS-5012-1-CE Bedienungsanleitung
