Siemens SINAMICS V20 Series Gebrauchsanweisung

Siemens V20 Frequency Inverter

Easy Start Guide

This guide is intended to compliment the user manual provided by the manufacturer.

It is provided as a basic introduction to the product for Inverter Drive Supermarket customers.

It should not be used as a replacement for the manual issued by the manufacturer.

Issue 1

20160509

This product is not a safety device. All safety considerations including but not

limited to Emergency Stop provision should be assessed separately and are

outside the scope of this guide.

The Siemens V20 Frequency Inverter range is

available to order from inverterdrive.com

L1 L2/N L3

W DC- DC+

DI 1

DI 2

DI 3

DI 4

DI C

24V

D0 1+

DO 1-

DO2

10V

AI 1

AI 2

AO 1

P+

N–

DANGER

RISK OF ELECTRIC

SHOCK! HAZARDOUS VOLTAGE PRESENT FOR

UP TO 5 MINUTES AFTER DISCONNECTION

FROM POWER SUPPLY! SEE INSTRUCTIONS!

Easy Start Guide

Page 1

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Page 9

Page 10

Page 11

Page 12

Contents

Power and Motor Connections (Single Phase)

Power and Motor Connections (Three Phase)

Motor Connections - Star and Delta

Parameters - Overview

Parameters to set before use

How to set a Parameter value

How to Operate the Inverter from the keypad

How to connect and configure a Potentiometer

for remote speed control

How to connect and configure a Run Forward or

Run Reverse switch

How to connect and configure a Run/Stop switch

with Forward/Reverse selection

How to configure “3-Wire” control with Run/Stop

pushbuttons and Forward/Reverse selection

How to Reset the Inverter to Factory Defaults

Contents

Siemens V20 Series Inverter

Easy Start Guide

1. Power and Motor Connections (Single Phase)

Page 2

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

Notes:

The illustration on the left is based on the

smaller 230V Single Phase frame size model

(to 0.75kW). The terminal layout for larger

frame sizes is similar.

The order of the three motor phases

determines the direction the motor turns.

Use screened cable between the Inverter and

Motor. To minimise electromagnetic

interference, ensure the cable screen is

grounded.

L1 L2/N L3

WDC- DC+

DI 1

DI 2

DI 3

DI 4

DI C

24V

D0 1+

DO 1-

DO2

10V

AI 1

AI 2

AO 1

P+

N–

DANGER

RISK OF ELECTRIC

SHOCK! HAZARDOUS VOLTAGE PRESENT FOR

UP TO 5 MINUTES AFTER DISCONNECTION

FROM POWER SUPPLY! SEE INSTRUCTIONS!

Earth

Earth Neutral

Phases

Before commencing, confirm that the

Inverter and all cables are completely

isolated from the power supply, have

been isolated for at least 5 minutes and

that the motor is not turning.

SUPPLY

MOTOR

Live

Siemens V20 Series Inverter

Easy Start Guide

2. Power and Motor Connections (Three Phase)

Page 3

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

Notes:

The illustration on the left is based on the

smaller 400V Three Phase frame size model

(to 0.75kW). The terminal layout for larger

frame sizes is similar.

The order of the three supply phases is

unimportant.

The order of the three motor phases

determines the direction the motor turns.

Use screened cable between the Inverter and

Motor. To minimise electromagnetic

interference, ensure the cable screen is

grounded.

Siemens V20 Series Inverter

L1 L2/N L3

WDC- DC+

DI 1

DI 2

DI 3

DI 4

DI C

24V

D0 1+

DO 1-

DO2

10V

AI 1

AI 2

AO 1

P+

N–

DANGER

RISK OF ELECTRIC

SHOCK! HAZARDOUS VOLTAGE PRESENT FOR

UP TO 5 MINUTES AFTER DISCONNECTION

FROM POWER SUPPLY! SEE INSTRUCTIONS!

Earth

Earth Phases

Phases

Before commencing, confirm that the

Inverter and all cables are completely

isolated from the power supply, have

been isolated for at least 5 minutes and

that the motor is not turning.

SUPPLY

MOTOR

Easy Start Guide

3. Motor Connections - Star and Delta

Page 4

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

3.2 Motor connected in DELTA:

The link configuration is shown in the

illustration opposite and is sometimes referred

to as “three-a-breast”.

The order of the three phases determines the

direction the motor turns.

Note that the cable screen and earth are

connected together at the motor earth

terminal.

Phase

Earth

Screen

3.1 Motor connected in STAR (or Wye):

For safety purposes, Star (shown opposite) is

the default configuration for small motors

(usually to 3kW) and is sometimes known as

“two at one side”.

Only two links are required for Star. Double-up

the links if changing from Delta to allow the

motor to be changed to back in future.

The order of the three phases determines the

direction the motor turns.

Note that the cable screen and earth are

connected together at the motor earth

terminal.

Phase

Earth

Screen

Dual voltage induction motors typically include

six connection terminals. The terminals can be

connected together with links in one of two

ways to suit one of the two rated voltages.

The two ways of connecting the links are

shown below. These are known as “Star” (the

higher voltage) or “Delta” (the lower voltage).

Link

The selection of Star or Delta is not optional

and must match the supply voltage.

Dual voltage motor nameplates include

symbols to represent voltage and full load

current in each configuration.

Delta is represented by a triangle and star by a

Y (Wye).

DELTA

STAR

Link

Siemens V20 Series Inverter

Easy Start Guide

Page 5

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

4. Parameters - overview

Parameter

Description

How to set

P0010

Commissioning parameter

Set to to enable quick commissioning.1

P0100

Europe / North America

Set to . 1 for North America (NA), hp, 60Hz or 2 for NA, kW, 60Hz.0 for Europe, kW, 50Hz

P0304

Motor rated voltage (V)

Set to for a 400V motor or for 230V to suit motor rating plate and terminal wiring.400 230

P0305

Rated motor current (A)

Rated current of the . Set to match motor nameplate and wiring - eg.Motor 3.34 Amps.

P0307

Rated motor power (kW/hp)

Rated power of the . Set to match motor nameplate in kW or hp depending on P0100.Motor

P0308

Rated motor power factor (cosφ)

Rated power factor of the . Enter cosφ value.Motor

P0310

Rated motor frequency (Hz)

Set to match motor nameplate - normally .50Hz for Europe

P0311

Motor rated speed (rpm)

Set to match motor nameplate approx. , 2800 for 2 pole etc.1400 for 4 pole

P0010

Commissioning parameter

Set to to indicate that commissioning is complete.0

P0003

User access level

Set to to allow access to extended parameters.2

P1080

Minimum motor frequency (Hz)

Set to for most applications. Can be set to the desired Hz for fixed speed applications.5

P1082

Maximum motor frequency (Hz)

Set to for most applications.50

P1120

Ramp-up time (s)

Time in seconds to accelerate from zero to maximum frequency. Default is 10.

P1121

Ramp-down time (s)

Time in seconds to decelerate from maximum frequency to zero. Default is 10.

P1032

Inhibit reverse setpoint selection

Change to if forward and reverse selection via keypad is required.0

The Inverter contains a number of settings

which can be changed to tailor it for use in a

wide range of applications. These settings are

known as parameters.

Parameters are typically referred to by code or

number (eg. P0305 = Rated Motor Current)

with a description available in the manual.

The parameters contain critical information

essential to the correct operation of the

Inverter. Therefore, they should at least be

checked by the user before the Inverter is

operated for the first time.

The parameters listed in section 5 are intended

to provide a starting point to allow for basic

operation of the V20 Inverter.

5. Parameters to set before use

See section 6 to learn how to set a parameter value.

Set the following parameters to allow the V20

to control a motor with Run, Stop and Speed

Control from the integrated keypad.

If any of the parameters have been changed

previously, follow the procedure in section 12

to reset the Inverter to Factory Defaults.

5.1 Parameters to check and values to set

Siemens V20 Series Inverter

Easy Start Guide

6. How to set a Parameter value

Page 6

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

6.1 Press the M key to access parameters.

With the motor stopped and from the status menu (see

illustration on the left), press the M key to access the

parameter menu.

Note: To access the status menu from another menu

press and hold the M key for 2 seconds.

6.2 Select the required parameter.

Use the up and down arrows to locate the parameter you

wish to change - in this case, P0305 motor rated current.

Press the OK key to select it.

Press the OK key again to select index in000 if prompted.

Note: If you are unable to locate the required parameter it

may be hidden. Change P0003 to 2 to enable extended

parameter access.

6.4 Change the parameter value.

Use the up and down arrow keys to change the value as

required. Press the OK to save the changes.

Press and hold the M key for 2 seconds to return to the

status menu.

Note: Depending on the value, pressing and holding

either the up or down key will change the value in larger

Siemens V20 Series Inverter

6.3 Select the Index (if prompted).

Some parameters contain multiple values which are

“indexed” as part of a set. This allows the V20 to be

configured for use in more than one application as a set

can be selected.

If only one application is required, simply press the OK

key to accept the default index of in000 as shown in the

illustration opposite.

Easy Start Guide

7. How to operate the Inverter from the keypad

Page 8

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

7.3 Changing speed and direction.

The up and down keys increase or decrease the speed.

Pressing the key will change the speed in small increments,

holding the key will change the speed in larger increments.

Press the up and down keys together to change direction.

The arrows icon (shown in the illustration opposite)

indicates when the motor is running in reverse. Note that

reverse direction is not enabled by default. Change P1032

to 0 to enable it.

7.1 Locate frequency in the status menu.

Press the OK button repeatedly to cycle through Output

Voltage (V), Output Current (A) and DC Bus Voltage (V)

until you reach Output frequency (Hz). Hz will be

displayed at the bottom of the screen as shown opposite.

Note: To reach the status menu from another menu,

press and hold the M button for 2 seconds.

7.2 Press the green I button to start the motor.

The green button will start the motor. Ensure it is safe to

do so before proceeding. When the motor is running, a

circular icon will be displayed as shown opposite.

Note: The time taken (in seconds) to reach maximum

speed is determined by parameter P1120. The time taken

to reach less than maximum speed will be proportional to

this.

Siemens V20 Series Inverter

7.4 Press the red button (labelled O) to stop the motor.

The red button will stop the motor. The circular run icon is no

longer displayed.

Note: The time taken (in seconds) to stop the motor from

maximum speed is determined by parameter P1121. The

time taken from a less than maximum speed will be

proportional.

Easy Start Guide

Page 9

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

8. How to connect and configure a Potentiometer

for remote speed control

Parameter

Description

How to set

P0003

User access level

Set to to allow access to extended parameters.2

P1000

Selection of frequency

Set value to for Analog as speed setpoint (select index first if prompted).2 in000

8.1 Parameters to change for remote Potentiometer speed control

If speed control via the up and down keys is

unsuitable for the application, a remote

Potentiometer can be used instead.

This provides the benefit of allowing motor

speed to be controlled from a more convenient

location such as a cabinet door (if the V20 is

cabinet-mounted) or on the machine itself.

A Potentiometer of more than 5kOhm rating

should be used eg. .10kOhm

The number of turns depends on the

application but both single turn and ten turn

Potentiometers are available from The Inverter

Drive Supermarket at InverterDrive.com.

8.2 Connecting the Potentiometer

A wiring diagram is shown in the illustration

opposite. The most important connection at

the Potentiometer end is the centre terminal or

“wiper”. The wiper will output a variable voltage

between 0 and 10 volts and should be

connected to the AI1 terminal on the Inverter. It

is this voltage which provides the speed signal

with 0V being slowest and 10V fastest.

The default output frequency at 10V is

determined by parameter P2000. The default

output frequency at 0V is determined by P0758

as a percentage of P2000.

If the rotation of the Potentiometer is the

opposite to that required (ie. turn anti-

clockwise to increase speed instead of

clockwise) reverse connections 10V and 0V.

Use screened cable between the Inverter and

Potentiometer. To minimise electromagnetic

interference, ensure the screen is grounded.

Screened

Cable

10kOhm

Potentiometer

[Order Code 21302]

Screen to

Earth Terminal

Siemens V20 Series Inverter

W DC- DC+

DI 1

DI 2

DI 3

DI 4

DI C

24V

D0 1+

DO 1-

DO2

10V

AI 1

AI 2

AO 1

P+

N–

12 3

Easy Start Guide

Page 10

This guide has been produced by The Inverter Drive Supermarket Ltd.

Drive Supermarket and must not be reproduced or altered without prior written permission.

9. How to connect and configure a Run Forward or

Run Reverse switch

9.1 Parameters to change for remote Run/Stop

The procedure described in Section 7 enable

Run/Stop operation via the red and green

buttons on the Inverter.

If this is unsuitable for the application, a remote

switch can be used instead.

This section explains how to enable 2-wire

control with Run Forward / Stop / Run Reverse

commands via a single selector switch.

9.2 Connecting the Switch

A wiring diagram is shown in the illustration

opposite. The 24V terminal is a common

connection for terminals DI1 and DI2. Note that

DIC and 0V must be linked (blue wire).

A suitable 3 position NO (Normally Open)

switch should be installed between terminals

DI1, DI2 and 24V. The centre position should

remain open circuit.

When a connection is made between terminals

DI2 and 24V, the motor will run forward. When

terminals DI1 and 24V are connected, the

motor will run in reverse.

If terminals DI1 and DI2 are connected to 24V

at the same time the motor will stop.

213

Switch, 3 Position

Normally Open

“Run Forward / Stop / Run Reverse”

[Order Codes 21720 and 21690 x 2]

Siemens V20 Series Inverter

W DC- DC+

DI 1

DI 2

DI 3

DI 4

DI C

24V

D0 1+

DO 1-

DO2

10V

AI 1

AI 2

AO 1

P+

N–

Parameter

Description

How to set

P0003

User access level

Set to to allow access to extended parameters.2

P0700

Selection of command source

Set value to for terminals as command source (select index first if prompted).2 in000

P0701

Function of digital input 1

Set value to for ON reverse (select index first if prompted).2 in000

P0702

Function of digital input 2

Set value to for ON (select index first if prompted).1 in000

P0727

Selection of 2/3-wire method

Set value to to enable 2-wire (fwd / rev) control (select index first if prompted).1 in000

Andere Handbücher für SINAMICS V20 Series

Inhaltsverzeichnis

Andere Siemens Gleichstromantrieb Handbücher

Siemens

Siemens SINAMICS S120 Kurzanleitung

Siemens

Siemens SIDOOR ATD400K Bedienungsanleitung

Siemens

Siemens CP 342-5 Bedienungsanleitung

Siemens

Siemens SED2 Series Benutzerhandbuch

Siemens

Siemens MICROMASTER 430 Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Stücklistenhandbuch

Siemens

Siemens SIDOOR AT12 Benutzerhandbuch

Siemens

Siemens SINAMICS G120C Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Benutzerhandbuch

Siemens

Siemens SINAMICS S120 Kurzanleitung

Siemens

Siemens Simovert 6SE70 Series Bedienungsanleitung

Siemens

Siemens SIMOVERT SLP Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Benutzerhandbuch

Siemens

Siemens MICROMASTER 420 Bedienungsanleitung

Siemens

Siemens SINAMICS G115D Bedienungsanleitung

Siemens

Siemens SINAMICS Technisches Dokument

Siemens

Siemens MICRO MASTER Junior Bedienungsanleitung

Siemens

Siemens SINAMICS G110 Bedienungsanleitung

Siemens

Siemens SIDOOR AT12 Bedienungsanleitung

Siemens

Siemens SINAMICS S110 Stücklistenhandbuch

Siemens

Siemens SINAMICS PERFECT HARMONY GH180 Bedienungsanleitung

Siemens

Siemens MICROMASTER 420 Bedienungsanleitung

Siemens

Siemens SKB62 Series Bedienungsanleitung

Siemens

Siemens SINAMICS G120 CU240B-2 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Minarik

Minarik MM300 Series Bedienungsanleitung