Siemens SITRANS F M MAG 8000 Bedienungsanleitung

A5E02972853-002, 03/2014 1

SITRANS F

Electromagnetic water meter

MAG 8000 Irrigation water meter

Quick Start

Preface

Before installing, including in hazardous areas, refer to the Operating Instructions on the internet or on the SITRANS F M

Manual Collection CD-ROM. They contain detailed safety regulations, information and specifications which must be

observed when installing. Documentation and approvals can be found on the internet:

Flow documentation (http://www.siemens.com/flowdocumentation)

CAUTION

Basic requirements for installation and operation

Correct, reliable operation of the device requires proper transport, storage, positioning and assembly. The device must be

carefully operated and maintained. Only qualified personnel should install or operate this device.

Items supplied

Note

The matched paired transmitter and sensor shall be mounted together. Please check in the installation that the system

nameplates of transmitter and sensor will have the same system serial number.

Safety notes

WARNING

NOT allowed for use in hazardous areas!

Equipment used in hazardous areas must be Ex-approved and marked accordingly!

This device is NOT approved for use in hazardous areas!

MAG 8000 Irrigation water meter

2A5E02972853-002, 03/2014

WARNING

Potential hazard

This device can contain lithium batteries.

Lithium batteries may present a potential hazard if they are abused electrically or mechanically.

Installation

Flow direction

Inlet and outlet conditions

Figure 4-1 Inlet and outlet conditions

Horizontal and vertical pipes

Horizontal pipes

Vertical pipes

MAG 8000 Irrigation water meter

A5E02972853-002, 03/2014 3

Positioning of sensor

Installation of the gaskets.

NOTICE

Grounding rings

Grounding rings are mandatory for MAG 8000 irrigation device operations.

Maximum allowable torques

Gasket hardness should be maximum 75 Shore A.

MAG 8000 Irrigation water meter

4A5E02972853-002, 03/2014

Table 4-1 Torques for 7ME6880

Nominal size

EN drilled

pattern

PN 7

ANSI

drilled pattern

Class 150

AS2091

drilled pattern

PN7

AS4087

PN 16

AS2129

Tabel E

PN 14

inch

f/lbs

25 1" N/A N/A N/A N/A N/A N/A N/A N/A 6 4

1½"

N/A

2½"

N/A

100

N/A

125

N/A

150

N/A

200

N/A

250

10"

N/A

300

12"

N/A

350

14"

153

113

N/A

400

16"

172

127

N/A

450

18"

224

165

N/A

500

20"

198

146

N/A

600

24"

104

111

287

211

N/A

700

28"

N/A

228

168

N/A

750

30"

N/A

800

32"

N/A

426

314

N/A

900

36"

N/A

416

307

N/A

1000

40"

N/A

386

284

N/A

1050

42"

N/A

1100

44"

N/A

1200

48"

N/A

443

327

N/A

MAG 8000 Irrigation water meter

A5E02972853-002, 03/2014 5

Remote version

1. Verify that model and serial numbers shown on labels of sensor and transmitter are matched properly.

2. Ensure that cable is safely installed to avoid damage to cable and connectors. Please note the different connector types

for coil and electrodes, both having a minimum radius of 45 mm (1.8 inches); otherwise there is a risk of damaging the

cable. Save dust covers for future use and protection.

3. Ensure connectors are clean.

4. Ensure connectors are fastened securely to achieve a good connection and watertight sealing.

Note

If dirt enters connector ends, use plain water for cleaning. Ensure connector

s are completely dry before making

connections.

NOTICE

Direct burial of remote sensor

The use of at least 300 mm pea gravel around the sensor and metal plate on top is mandatory for direct burial of remote

sensor.

MAG 8000 Irrigation water meter

6A5E02972853-002, 03/2014

Sealing of transmitter

1. Select the proper gland size to fit installed cable size.

2. Mount O-ring properly and correctly and grease with gel.

3. Fill Sylgard potting kit in bottom part of casing.

4. Renew Silicagel bag to prevent condensation within transmitter, if necessary.

5. Mount the enclosure carefully and make sure not to damage the O-ring.

The self-calibration of the capacitive operation key will take 3 to 5 minutes once the MAG 8000 transmitter enclosure is

removed and mounted again. During this self-calibration the device cannot be operated via the operation key.

CAUTION

Maintain IP rating when mounting

The mains or line powered PUR cable (no shield) has to be mounted under the cable clamps. All cable glands have to be

sufficiently tightened to ensure the IP rating.

Connecting

①

Module Interface (Option)

②

Output A

③

Output B

The 3.6 V DC battery connector and pulse connection terminals are placed in the right side of the PCB board - see figure.

Connection for add-on interface modules is placed on the left side.

HL = Hardware lock key connection

V = Verification button

MAG 8000 Irrigation water meter

A5E02972853-002, 03/2014 7

Power supply

Connection diagram for 115 to 230 V AC (mains) or 12/24 V AC/DC (line) power supply

Backup battery connection

①

Red

②

Black

MAG 8000 PCB connection

③

Blue

④

Yello

External power supply connection

⑤

Blue (N

eutral /

)

⑥

Brown (L

ine /

)

Shielding

⑦

Shielding wire

It is mandatory to connect the shielding wire to the MAG 8000 device earthing; otherwise IrDA communication will not work

properly.

Pulse output connection

MAG 8000 internal connection

①

②

③

Output A

Output B

Passive output - no polarization - open drain

MAG 8000 Irrigation water meter

8A5E02972853-002, 03/2014

External connection variant

④

⑤

⑥

Positive pule logic

Negative pulse logic

Signal

Cable installation

Ensure shield is mounted under cable clamps - do not make pig tails.

Commissioning

For detailed settings refer to the Operating Instructions on the enclosed documentation CD, or download from Siemens Flow

Product Support website: flowdocumentation (http://support.automation.siemens.com/WW/view/en/66508574).

MAG 8000 Irrigation water meter

A5E02972853-002, 03/2014 9

Operation via key and display

The meter is designed with a single key and a symbolic display for optimal dialog.

: Status

: Measured value

: Index number, menu symbols

D: Operation key

Figure 8-1 Key and display operation

MAG 8000 Irrigation water meter

10 A5E02972853-002, 03/2014

Andere Handbücher für SITRANS F M MAG 8000

Inhaltsverzeichnis

Sprachen:

Andere Siemens Messgerät Handbücher

Siemens

Siemens WTV676-HB6035 Bedienungsanleitung

Siemens

Siemens FIDAMAT 6 Bedienungsanleitung

Siemens

Siemens sitrans PROBE LU Gebrauchsanweisung

Siemens

Siemens sitrans lr 460 Bedienungsanleitung

Siemens

Siemens SIRIUS 3SE670 BA Series Bedienungsanleitung

Siemens

Siemens SIRIUS 3RK1105-1 E04 Series Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens SITRANS DA400 Bedienungsanleitung

Siemens

Siemens Sicam P855 7KG85 Series Anwendungshandbuch

Siemens

Siemens SITRANS FUP1010 Bedienungsanleitung

Siemens

Siemens ADVIA 1800 Handbuch

Siemens

Siemens FUS1010 Bedienungsanleitung

Siemens

Siemens SITRANS F C MC2 Bedienungsanleitung

Siemens

Siemens SENTRON PAC1020 Bedienungsanleitung

Siemens

Siemens UH50 Series Bedienungsanleitung

Siemens

Siemens WFM407 series Bedienungsanleitung

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Bedienungsanleitung

Siemens

Siemens CLINITEK Status Bedienungsanleitung

Siemens

Siemens SITRANS F M MAG 5000 Bedienungsanleitung

Siemens

Siemens SITRANS LR 400 Bedienungsanleitung

Siemens

Siemens CLINITEK Status+ Handbuch

Siemens

Siemens LMS SCADAS XS Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens SENTRON PAC3100 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung