Siemens SITRANS FUP1010 Bedienungsanleitung

JASPER ENGINEERING & EQUIPMENT

800-776-6184

www.jaspereng.com

[email protected]

Proudly Serving Customers since 1958

Siemens SITRANS FUP1010

Quick Start Part One:

Instrument Setup

Power On Instrument

Press ON/OFF utton. Display will show the

WELCOME splash screen:

Enter FastStart Setup Mode

Press MENU. Display will show the following:

Press RIGHT ARROW twice to select Single

Channel. Display will show the following:

[x2]

Press RIGHT ARROW twice to select Clamp-on.

Display will show the following:

[x2]

Press RIGHT ARROW once to enter FastStart

Setup.

Input Pipe D

ata

Press RIGHT ARROW to open pipe material

selection. Use UP and DOWN arrows to select

appropriate material and press ENTER to confirm:

Press RIGHT ARROW to open pipe size selection.

Use UP and DOWN arrows to select appropriate

pipe size/ schedule and press ENTER to confirm:

Press RIGHT ARROW next to Install Sensor to

enter Sensor Installation Mode.

4. Select Transducers

From Sensor Installation Mode, press DOWN

ARROW once to select Sensor Size. Based on

entries in [3], the FUP1010 will recommend

transducers. This will e shown on the second line

from the top:

Press RIGHT ARROW to open sensor selection. Use

UP and DOWN arrows to select appropriate

sensor ased on recommendation and inventory.

Press ENTER to confirm selection.

Screen will now populate with sensor spacing, mode, offset,

track type, and linear value. Use Num er Offset and Sensor

Size information to physically install transducers on pipe:

Follow instructions on reverse to install transducers.

JASPER ENGINEERING & EQUIPMENT

800-776-6184

www.jaspereng.com

[email protected]

Proudly Serving Customers since 1958

Siemens SITRANS FUP1010

Quick Start Part Two:

Transducer Setup

5. Prepare Transducers

Retrieve appropriate transducers from case ased on Sensor

Size entry in [4]. Make sure serial num ers match, ending in A

and B:

Unscrew thum screws from spacer ar and use to space

sensors ased on Spacing Offset from [4]. Sensor BNC ca le

ports should face away from each other:

Apply a generous line of ultrasonic coupling compound to the

ottom of each transducer:

. Prepare

Pipe

Pipe must e clean and free of rust, loose paint, and other

contaminants. Use supplied a rasive sponge to clean surface

prior to installation. Note that severely rusted pipes may

need to e cleaned with a powered a rasive tool. Cast iron

pipe may need surface smoothed out.

Mount Transducers

and Ca les

Insert supplied clamps through transducer mounting slots

and around pipe. Tighten using a 5/16” hex driver, ensuring

that transducer mounting frame is parallel to pipe and

transducers are square:

Install supplied 20’ ca les onto transducers. BNC connectors

use a collar that must e pressed on and rotated to secure.

Ca les are marked UP and DN for upstream and downstream

sensors:

Insert transducer ca le connector into FLOW SENSOR port on

rear of FUP1010. Connector is polarized and will only fit one

way. As with BNC ca les, collar rotates to secure:

Complete Installation

On FUP1010 install menu from [4], use DOWN ARROW to

select Install Complete. Press RIGHT ARROW to pop up menu

and press DOWN ARROW to select INSTALL. Press ENTER.

System will run through makeup routine for several minutes.

When meter provides sonic velocity, press MENU. Press LEFT

ARROW to return to flow screen.

Andere Handbücher für SITRANS FUP1010

Inhaltsverzeichnis

Andere Siemens Messgerät Handbücher

Siemens

Siemens 5SV8001-6KK Bedienungsanleitung

Siemens

Siemens VDO EDM eco Release II Bedienungsanleitung

Siemens

Siemens SITRANS F FC410 Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens 5TT3 196 Bedienungsanleitung

Siemens

Siemens as-interface ANALYSER 3RK1 904-3AB01 Bedienungsanleitung

Siemens

Siemens SD 270 Bedienungsanleitung

Siemens

Siemens Ardoptix PT 140 AF4 Bedienungsanleitung

Siemens

Siemens 6 Series Administratorhandbuch

Siemens

Siemens sitrans PROBE LU Bedienungsanleitung

Siemens

Siemens SITRANS F Administratorhandbuch

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

Siemens

Siemens 7ME4613 Betriebsanleitung

Siemens

Siemens SITRANS FUS380 Bedienungsanleitung

Siemens

Siemens 9200 Technisches Datenblatt

Siemens

Siemens SIPLUS CMS Bedienungsanleitung

Siemens

Siemens SIRIUS 3RR2143 A.30 Series Bedienungsanleitung

Siemens

Siemens SITRANS F M MAG 1100 Bedienungsanleitung

Siemens

Siemens Clinitek Advantus Bedienungsanleitung

Siemens

Siemens SITRANS LU AO Bedienungsanleitung

Siemens

Siemens FS720 Series Betriebsanleitung

Siemens

Siemens SITRANS FUS1020 Bedienungsanleitung

Siemens

Siemens Sicam P855 7KG85 Series Anwendungshandbuch

Siemens

Siemens SIWAREX WL270 CP-S SA Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung