Siemens SMART 7KT Bedienungsanleitung

SMART 7KT0307 Manual

MANUAL

SMART KT

Multifunction meter

7KT0307 (Single Line LED Class 1)

SMART 7KT power monitoring devices

SMART 7KT0307 Manual

1. Introduction 3

2. Safety precautions 4

3. Technicalspecication 5

4. Installation 7

5. Connection 9

6. Conguration 11

7. Communication 16

8. Maintenance 18

SMART 7KT

Multifunction meter

7KT0307 (Single Line LED Class 1)

Manual

Index

09/2022

SME7KT030700

SMART 7KT0307 Manual

Introduction 

1.1 Purpose of this document

This present manual describes the SMART 7KT multifunction meter.

It is intended for the use of:

• Planners

• Plantoperators

• Commissioningengineers

• Serviceandmaintenancepersonnel

1.2 Required basic knowledge

Ageneralknowledgeoftheeldofelectricalengineeringisrequiredtounderstandthismanual.

Knowledgeoftherelevantsafetyregulationsandstandardsisrequiredforinstallingandconnectingthedevice.

1.3 Components of the product

The carton for the products contain

1 SMART 7KT meter

1 set of clamps (4 clamps) for mounting the meter on the panel door

1 Gasket

1 Operating instruction

Unit 1x nos. Gasket 1x nos. Sliding Clamp 4x nos.

SMART 7KT0307 Manual

Safety

precautions 

DANGER

Hazardous voltage will cause death or serious injury. Turn off and lock out all

powersupplybeforeworkingonthisdevice.

NOTICE

Installationandmaintenancemustbecarriedoutbyqualied

personnel.

ThisproducthasbeendesignedforenvironmentA.Use

ofthisproductinenvironmentBmaycauseunwanted

electromagnetic disturbances in which case the user may

requiretotakeadequatemitigationmeasures.

Risk of damage: Please ensure the proper isolation of meter

during the IR (Meggering) test.

Allsafetyrelatedcodications,symbolsandinstructionsthatappearinthisoperatingmanualorontheequipment

mustbestrictlyfollowedtoensurethesafetyoftheoperatingpersonnelaswellastheinstrument.Iftheequipmentis

notusedinamannerspeciedbythemanufactureritmightimpairtheprotectionprovidedbytheequipment.

Donotusetheequipmentifthereisanymechanicaldamage.

Ensurethattheequipmentissuppliedwithcorrectvoltage.

NOTICE:

ThisproducthasbeendesignedforenvironmentA.UseofthisproductinenvironmentBmaycauseunwanted

electromagneticdisturbancesinwhichcasetheusermayrequiretotakeadequatemitigationmeasures.

Riskofdamage:PleaseensuretheproperisolationofmeterduringtheIR(Meggering)test.

CAUTION:

1. Read complete instructions prior to installation and operation of the unit.

2. Risk of electric shock.

3. Theequipmentinitsinstalledstatemustnotcomeincloseproximitytoanyheatingsources,oils,steam,

causticvaporsorotherunwantedprocessbyproducts.

SMART 7KT0307 Manual

Technical

speciﬁcation 

7KT0307 (Single Line LED Class 1)

PowerMonitoringDevicePanelinstrumentforstdelectricalvalues

Protocol:ModbusRTU,SinglelineLEDDisplayVaux:95Vto240VAC

x/1or5A,Class1

Measurements

measuring procedure

•forvoltagemeasurement True RMS

•forcurrentmeasurement True RMS

typeofmeasuredvaluedetection complete

voltagecurve Sinusoidal or distorted

measurablelinefrequency

•initialvalue 45Hz

•full-scalevalue 65Hz

operatingmodeformeasuredvaluedetectionautomaticline

frequencydetection

Yes

Supply voltage

design of the power supply SMPSpowersupply

typeofvoltageofthesupplyvoltage AC

Degree of protection class

protectionclassIPonthefront IP54

protectionclassIPoftheterminal IP20

Suitability

suitability for operation Installation in stationary panels in closed rooms

Product Functions

product function

•voltagemeasurement Yes

•currentmeasurement Yes

•activepowermeasurement Yes

•reactivepowermeasurement Yes

•apparentpowermeasurement Yes

•powerfactormeasurement Yes

•frequencymeasurement Yes

•apparentenergy/activeenergy/reactiveenergy Yes

Display and operation

design of the display LED

height of the display 22 mm

width of the display 69mm

color of the background of the display Black

national language on the display screen is supported EN

number of keys 2

Fault limits

reference condition for metering accuracy InaccordancewithIEC61557-12,IEC62053-21,IEC62053-23

formulaforrelativetotalmeasurementinaccuracy

•formeasuredvariablevoltage Class0.5asperIEC61557-12

•formeasuredvariablecurrent Class0.5asperIEC61557-12

•formeasuredvariableapparentpower Class1asperIEC61557-12

•formeasuredvariableactivepower Class1asperIEC61557-12

•formeasuredvariablereactivepower Class2asperIEC61557-12

•formeasuredvariablepowerfactor Class1asperIEC61557-12

•formeasuredvariableactiveenergy Class1asperIEC62053-21andIEC61557-12

•formeasuredvariablereactiveenergy Class2asperIEC61557-12andIEC62053-23

SMART 7KT0307 Manual

IEC Standards

Description Standard

Accuracy IEC61557-12;

IEC62053-21|ActiveEnergy

EMCrequirements IEC61326-1

Degreeofprotectiontest(IP) IEC60529

Safetyrequirements IEC61010-1and

IEC61010-2-030

7KT0307 (Single Line LED Class 1)

Measuring inputs

measurablesupplyvoltagebetweenLandNatACmaximumrated

value

240V

measurablesupplyvoltagebetweenLandNatAC

•minimum 11V

•maximum 300V

measurablesupplyvoltagebetweenthelineconductorsatAC

maximumratedvalue

415V

measurablesupplyvoltagebetweenthelineconductorsatAC

•minimum 19V

•maximum 519V

voltagemeasuringrangeextensionwithexternalvoltage

transformers

upto500kV

line conductors and neutral conductors internal resistance for

voltagemeasurement

1.12MΩ

measuringcategoryforvoltagemeasurement CAT III

measurable current 1A/5A

relativemeasurablecurrentatAC

•minimum 1 %

•maximum 120 %

current measuring range extension with external current

transformers

up to 10kA

measuring category for current measurement CAT III

Connections

type of electrical connection

•atthemeasurementinputsforvoltage screw-typeterminals

•atthemeasurementinputsforcurrent screw-typeterminals

Mechanical Design

mounting ushpanel-doormounted

sizeofPowerMonitoringDevice size96

height 99mm

width 99mm

cut-out 91.5mmx91.5mm

depth 52mm

installation depth 49mm

net weight 228 g

mounting position Vertical

Environmental conditions

ambient temperature during operation

•minimum -10°C

•maximum 55°C

ambient temperature during storage

•minimum -20°C

•maximum 75°C

relativehumidityat25°Cwithoutcondensationduringoperation

maximum

85%

installationaltitudeatheightabovesealevelmaximum 2 000 m

degree of pollution 2

Certications

SMART 7KT multifunction meter conforms to IEC

standards,IPCelectronicsassemblystandardand RoHS

SMART 7KT0307 Manual

Assembly 

Installation

For installing the meter

Preparethepanelcutoutwithproperdimensionsasshownbelow.

OUTLINE

Dimensions (in mm)

PANEL CUTOUT

Dimensions (in mm)

SMART 7KT0307 Manual

Installation Guidelines

1. Thisequipment,beingbuilt-in-type,normallybecomesapartofmaincontrolpanelandinsuchcasetheterminals

do not remain accessible to the end user after installation and internal wiring.

2. Conductorsmustnotcomeincontactwiththeinternalcircuitryoftheequipmentorelseitmayleadtoasafety

hazardthatmayinturnendangerlifeorcauseelectricalshocktotheoperator.

3. Circuit breaker or mains switch must be installed between power source and supply terminals to facilitate

power‘ON’or‘OFF’function.Howeverthisswitchorbreakermustbeinstalledinaconvenientpositionnormally

accessible to the operator.

4. Beforedisconnectingthesecondaryoftheexternalcurrenttransformerfromtheequipment,makesurethatthe

currenttransformerisshortcircuitedtoavoidriskofelectricalshockandinjury.

5. Theequipmentshallnotbeinstalledinenvironmentalconditionsotherthanthosementionedinthismanual.

6. Theequipmentdoesnothaveabuilt-in-typefuse.Installationofexternalfuseof0.5A,ClassgGtypeforelectrical

circuitry is highly recommended.

7. Removethescratch-guardfromthemeterdisplayduringcommissioningofthepanel.

Wiring Guidelines

1. Topreventtheriskofelectricshock,powersupplytotheequipmentmustbekeptOFFwhiledoingthewiring

arrangement.

2. Wiringshallbedonestrictlyaccordingtotheterminallayout.Conrmthatallconnectionsarecorrect.

3. Use lugged terminals.

4. Toreduceelectromagneticinterferenceuseofwireswithadequateratingsandtwistsofthesameinequalsize

shall be made with shortest connections.

5. LayoutofconnectingcablesshallbeawayfromanyinternalEMIsource.

6. Cableusedforconnectiontopowersource,musthaveacross-sectionof1mm2to2.5mm2.Thesewiresshallhave

current carrying capacity of 6A.

7. Copper cable should be used (Stranded or Single core cable).

For demounting the meter

SMART 7KT0307 Manual

Connection 

3 Phase - 4 Wire

3Ø-4Wire,3CT’sand3PT’s

2 Phase - 3 Wire

2Ø-3Wire,2CT’sand2PT’s

3 Phase - 4 Wire (commonly used)

3Ø-4Wire,3CT’s

3 Phase - 3 Wire

3Ø-3Wire,2CT’sand2PT’s

Typical Wiring Diagram

SMART 7KT0307 Manual

Terminal Connections

1 Phase - 2 Wire

1Ø-2Wire,1CT

Typical Wiring Diagram (Continued)

Andere Handbücher für SMART 7KT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Messgerät Handbücher

Siemens

Siemens SITRANS SL Bedienungsanleitung

Siemens

Siemens SENTRON PAC2200CLP Bedienungsanleitung

Siemens

Siemens VDO EDM eco Release II Bedienungsanleitung

Siemens

Siemens SITRANS RD300 Bedienungsanleitung

Siemens

Siemens SITRANS FC720 Bedienungsanleitung

Siemens

Siemens SITRANS FS230 Administratorhandbuch

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens SICAM Q100 7KG95 Series Bedienungsanleitung

Siemens

Siemens SIMEAS P 7KG7750 Bedienungsanleitung

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Bedienungsanleitung

Siemens

Siemens SITRANS F FM100 Bedienungsanleitung

Siemens

Siemens Healthineers Atellica VTLi Bedienungsanleitung

Siemens

Siemens SITRANS F Administratorhandbuch

Siemens

Siemens SIWAREX WL230 BB-S SA Bedienungsanleitung

Siemens

Siemens Sitrans LR200 Benutzerhandbuch

Siemens

Siemens DELTA 5TC8 425 Service-Handbuch

Siemens

Siemens 9330 series Bedienungsanleitung

Siemens

Siemens SITRANS MAG 5100W Bedienungsanleitung

Siemens

Siemens 7KG85 Series Bedienungsanleitung

Siemens

Siemens milltronics ILE-37 Bedienungsanleitung

Siemens

Siemens CALOMAT 6 Bedienungsanleitung

Siemens

Siemens sitrans lc 300 Bedienungsanleitung

Siemens

Siemens SITRANS F M MAG 3100 Bedienungsanleitung

Siemens

Siemens SITRANS FC430 Administratorhandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung