Siemens Rider 11, Rider 13 H,Rider 11 Bio Gebrauchsanweisung

Interface modules IM 153-4 PN and IM

153-2 HF

___________________

SIMATIC

ET 200M

Interface modules IM 153-4 PN and

IM 153-2 HF

Product Information

12/2013

A5E02714952

-04

Introduction

Product information

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E02714952-04

Ⓟ

01/2014 Technical data subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Interface modules IM 153-4 PN and IM 153-2 HF

Product Information, 12/2013, A5E02714952-04 3

Table of contents

1 Introduction............................................................................................................................................. 5

2 Product information................................................................................................................................. 7

2.1 Supplement to the sections............................................................................................................7

2.2 The new functions for the IM 153-4 .............................................................................................10

Table of contents

Interface modules IM 153-4 PN and IM 153-2 HF

4Product Information, 12/2013, A5E02714952-04

Interface modules IM 153-4 PN and IM 153-2 HF

Product Information, 12/2013, A5E02714952-04 5

Introduction

Overview

This product information applies to:

●IM 153-4 PN interface module

–6ES7153-4AA01-0XB0, as of firmware version 4.x

–6ES7153-4BA00-0XB0, as of firmware version 4.x

●IM 153-2 HF interface module

–6ES7153-2BA02-0XB0

–6ES7153-2BA82-0XB0

Supplement to the ET 200M operating instructions

This product information is a supplement to the ET 200M

(http://support.automation.siemens.com/WW/view/en/1142798) operating instructions.

IM 153-4AA0x

The following changes have been made:

Property

6ES7153-4AA01-0XB0

6ES7153-4BA00-0XB0

Shared Device

Media redundancy

Isochronous real-time communication

IRT option "high performance"

× ×

F modules

—

Connection to H-CPUs with system

redundancy

— ×

HART modules

—

Introduction

Interface modules IM 153-4 PN and IM 153-2 HF

6Product Information, 12/2013, A5E02714952-04

Configuration with STEP 7 or GSD

You can configure the ET 200M using the above-named 6ES7153-4AA01-0XB0/6ES7153-

4BA00-0XB0 under STEP 7 V5.5 (with HSP 214 or HSP 213) or a GSD file.

You can find the GSD file at Internet

(http://support.automation.siemens.com/WW/view/en/25057900).

The F modules of the 6ES7153-4BA00-0XB0 can only be configured with STEP 7.

You can configure the HART modules

●6ES7331-7TF01-0AB0

●6ES7331-7TB00-0AB0

●6ES7332-8TF01-0AB0

●6ES7332-5TB00-0AB0

with STEP 7 V5.5 SP3 and SIMATIC PDM V8.0 SP2 (HART on PROFINET).

IM 153-2BAx2

The following changes have been made to the technical specifications of the 6ES7153-

2BAx2-0XB0 as of product version 02:

Voltage, Currents, Potentials

Current consumption from 24 V max. 600 mA (for 6ES7153-2BAx2, product version 01)

max. 620 mA (for 6ES7153-2BAx2, product version 02)

Interface modules IM 153-4 PN and IM 153-2 HF

Product Information, 12/2013, A5E02714952-04 7

Product information

2.1

Supplement to the sections

Supplement to the ET 200M operating instructions

This section lists all of the supplements to the sections of the ET 200M operating

instructions.

Supplement to section 3.5.4: Arrangement of the modules for the function "Change During Operation"

and/or "Redundancy"

IM 153-2BA02 and IM 153-2BA82

: Maximum 12 signal modules, FMs and CPs can be

plugged next to the IM 153-2BA02 and IM 153-2BA82.

Supplement to section 7.7: Replace modules with the function "Change During Operation"

New sequence for the individual steps for "Removing a module"

When removing modules with "Module Change During Operation" proceed as follows:

1. Switch off the voltage.

2. Open the front door (3).

3. Unlock the front connector and remove it.

–With 20-pin front connector: To do this, use one hand to press down the unlocking

button (4) and use your other hand to remove the front connector via the gripping

surface (4a).

–With 40-pin front connector: Release the fixing screw in the center of the front

connector. Use the gripping surface to pull out the front connector.

4. Loosen the fixing screw(s) on the module (1).

5. Swing the module out.

6. Pull the labeling strips out of the module (5).

Product information

2.1 Supplement to the sections

Interface modules IM 153-4 PN and IM 153-2 HF

8Product Information, 12/2013, A5E02714952-04

Supplement to section 7.10.4: Update of the IM 153-2Bxx1

Configuration as IM 153-2Bxx1

The firmware update is created separately with each IM 153-2.

The IM 153-2 is integrated in the PCS 7 project.

Procedure

1. Open the SIMATIC Manager.

2. In the component view, select the SIMATC station in which the IM 153-2 is located.

3. Double-click on the "Hardware" object in the detail window.

HW Config opens.

4. Select the IM 153-2 with the firmware you want to update.

5. Select the menu command

Target system > Update Firmware

The "Update Firmware" dialog box opens.

6. Make the settings according to the following table.

7. Click the "Run" button. The firmware update is performed.

Setting

Action

Location of the

firmware file

Specify the folder in the "Firmware file" group, in which you have saved the file for updating the

firmware.

Activate the "new"

firmware

Use the "Activate firmware after download" check box to specify the time at which the "new"

firmware should be activated:

•Select the "Activate firmware after download" option if the IM 153-2 should automatically

perform a RESET upon successful download of the new firmware. The new firmware in then

active after restart.

•Clear the "Activate firmware after download" option if the IM 153-2 no RESET should be

performed upon successful download of the new firmware. The new firmware then only

becomes active after the supply voltage has been switched off.

In the redundant system with PROFIBUS DP

Following the firmware update of the active IM 153-2, the subsequent "RESET" automatically

switches between the two IM 153-2.

Supplement to section 8.2: Time stamping the input signals with IM 153-2

Rules

You can also use following digital input modules: 6ES7 321-7EH00-0AB0 (1 ms)

Supplement to section 8.4: Redundancy:

Rules for arranging fault-tolerant station components

In a fault-tolerant station, the following conditions must be met for the ET 200M:

Redundantly used modules (DP slave interface modules IM 153-2) must be identical, i.e.

they must have the same order number and the same product version or firmware version.

Product information

2.1 Supplement to the sections

Interface modules IM 153-4 PN and IM 153-2 HF

Product Information, 12/2013, A5E02714952-04 9

Supplement to section 9.1.3.1: Structure of the slave diagnostics

If you have not performed the configuration with GSD, there are no module status and

channel-related diagnostics blocks for the IM 153-1AA03.

Figure 2-1 Structuring of the slave diagnostics new

Product information

2.2 The new functions for the IM 153-4

Interface modules IM 153-4 PN and IM 153-2 HF

10 Product Information, 12/2013, A5E02714952-04

Error in section 10.1 Pollutant concentration

This sentence is correct: The ET 200M distributed I/O system satisfies the requirements of

the standard ISA-71.04 serverity level G1;G2;G3.

2.2

The new functions for the IM 153-4

Media redundancy

Function for ensuring the network and system availability. Redundant transmission links (ring

topology) ensure that an alternative communication path is made available if a transmission

link fails.

You can find additional information in the STEP 7 online help and the PROFINET system

description (http://support.automation.siemens.com/WW/view/en/19292127) manual.

Shared Device

The "Shared Device" function allows the submodules of an IO device to be divided up

among different IO controllers.

The following conditions apply for an ET200M if it is to be operated as a shared device.

You can find additional information in the STEP 7 online help and the PROFINET system

description (http://support.automation.siemens.com/WW/view/en/19292127) manual.

The following applies to the ET 200M:

●If an IO controller fails, the entire IO device outputs substitute values. This means that not

only do the IO modules of the failing IO controller output substitute values, but also the IO

modules of the intact IO controller.

●Since the outputs of an IO module cannot separately output substitute values, in the

shared device environment the I/O will only output process values if both IO controllers

are in RUN.

As soon as an IO controller is in STOP mode, the outputs of that IO module that are

subscribed by the other IO controller will therefore output substitute values. This fact must

be taken into account, for example, for the STEP 7 functions, "Modify" and "Force". With

the STEP 7 "Modify" and "Force" functions, a CPU in STOP mode will be reported as

being in RUN mode. This releases the modules that are assigned to the other controller

that is still in RUN.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Netzwerk-Hardware Handbücher

Siemens

Siemens SIMATIC NET CP 1515 Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RX1536 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RX1511 Bedienungsanleitung

Siemens

Siemens SIMATIC NET PROFIBUS Bedienungsanleitung

Siemens

Siemens 181 Gebrauchsanweisung

Siemens

Siemens SANTIS-ab Bedienungsanleitung

Siemens

Siemens RUGGEDCOM WIN5114-V-GPS Bedienungsanleitung

Siemens

Siemens RUGGEDCOM MX5000 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM MX5000RE Technisches Dokument

Siemens

Siemens SIMATIC NET Bedienungsanleitung

Siemens

Siemens SIMATIC NET SCALANCE W M766 Series Bedienungsanleitung

Siemens

Siemens SIMATIC PN/CAN LINK Bedienungsanleitung

Siemens

Siemens Simatic S7-400 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 243-2 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM WIN7251 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA2130 Bedienungsanleitung

Siemens

Siemens WTT16 Series Bedienungsanleitung

Siemens

Siemens Sinumerik 810T Bedienungsanleitung

Siemens

Siemens SCALANCE W788C-2 Bedienungsanleitung

Siemens

Siemens ESM Bedienungsanleitung

Siemens

Siemens XT55 AVL Bedienungsanleitung

Siemens

Siemens SIMATIC NET S7-CPs Bedienungsanleitung

Siemens

Siemens SIMATIC NET SCALANCE W774-1 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840Di sl Stücklistenhandbuch

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung