Siemens RNI Bedienungsanleitung

Siemens BuildingSiemens Building

Siemens Building

Tecec

ecec

echnologieshnologies

hnologieshnologies

hnologies

Fire SFire S

Fire Safetyafety

afetyafety

afety

P/N 315-033420-4

INTRODUCTION The SIEMENS Model RNI allows for the remote

installation of the PMI-REM, SSD-C-REM (on HNET)

and the LCM-8/SCM-8/FCM-6/SIM-16/OCM-16 (on

CAN) modules.

The HNET can be wired either Style 4 or Style 7.The

CAN network may only be wired Style 4. The RNI

may be placed in the middle or at the end of either

the HNET or CAN networks. A 24VDC input is also

required.This can be obtained from the PSC-12

power limited output (TB3) or any UL/ULC regulated,

power limited power supply listed for fire protective

signaling use.

The RNI mounts in the rear of either the REMBOX2

or REMBOX4 enclosures.The RNI provides terminal

blocks for all field wiring connections. Internal

connections are made to plug in connectors specifi-

cally provided for each of the installed modules.

The HNET and the CAN networks can be used

simultaneously.

PRE-INSTALLATION P7 enables or disables an audible device similar to the CSB.This audible sounds

whenever a switch is pressed on either the SCM-8 or the FCM-6. If this is not desired

the audible can be silenced by changing the jumper installed on P7 to positions 2 and

3. P7 is configured in the factory (positions 1 and 2) to have the audible active.

S1 is used to terminate the HNET. If the RNI is installed at the end of an HNET

network S1 must be set to the ON position. If the RNI is in the middle of the HNET

set S1 to the OFF position.

P5 must be set to the HNET (H) position.

Remote Network Interface

Installation Instructions

Model RNI

24 V

TB1

P3 P4

TB2

RNI

TB3 TB4 TB5 TB6

JP1

OFF

Figure 1

RNI Remote Network

Interface

Siemens Building Technologies

Fire Safety

P/N 315-033420-42

Figure 2

Connecting The 24VDC Input

Figure 3

Connecting HNET At The End Of The Network (Style 4 and Style 7)

NOTES:

1. 18 AWG min.

2. 2A max. input current.

3. Supervised

4. Refer to PSC-12/PSX-12

Installation Instructions,

P/N 315-033060 for

connection to TB3.

NOTES:

1. No EOLR required.

2. 24 AWG min., 12 AWG max.

3. 80 ohms max. per pair.

4. Use twisted pair or twisted

shielded pair.

5. Power limited to NFPA 70

per NEC 760.

6. Refer to NIC-C Installation

Instructions, P/N 315-

033240 for connection of

A and B pairs.

7. Omit B pair for Style 4.

8. All wiring supervised.

24 V

–

TB1

RNI

TO PSC-12 TB3

OR ANY UL/ULC

REGULATED,

POWER LIMITED

POWER SUPPLY

LISTED FOR FIRE

PROTECTIVE

SIGNALING USE

SHIELD

A–

A+

B–

B+

TB2

RNI

FROM

NIC-C

SHIELD

SET TO ON

PRESS

DOWN

SHIELD

INSTALLATION

Disconnect BATTERY and AC prior to working on equipment.

The RNI mounts on studs in the rear of either the REMBOX2 or the REMBOX4. Four

#8/32 nuts are provided with the RNI. (Refer to the REMBOX2/REMBOX4 Installation

Instructions, P/N 315-033772.) Install the RNI with the terminal blocks facing up to

allow for easier connection of the field wiring.

Connecting The PMI-REM A 24 inch long 60 wire cable, P/N 555-133998 (shipped with the PMI-REM), connects

the RNI to the PMI-REM. Connect one end of the cable to JP1 on the RNI and the

other end of the cable to JP3 on the PMI-REM. Be sure that the PMI-REM address

agrees with the ZEUS configuration. Refer to the PMI-REM Installation Insturctions,

P/N 315-033070.

Siemens Building Technologies

Fire Safety

P/N 315-033420-43

Figure 4

Connecting HNET In The Middle Of The Network (Style 4 and Style 7)

NOTES:

1. No EOLR required.

2. 24 AWG min., 12 AWG max.

3. 80 ohms max. per pair.

4. Use twisted pair or twisted

shielded pair.

5. Power limited to NFPA 70

per NEC 760.

6. Refer to NIC-C Installation

Instructions, P/N 315-

033240 for connection of

A and B pairs.

7. Omit B pair for Style 4.

8. All wiring supervised.

A–

A– A–

A+

A+ A+

B–

B– B–

B+

B+ B+

TB2

RNI

FROM

NIC-C

OR RNI SHIELD

SHIELD

SET TO OFF

PUSH

TO NEXT

NIC-C

OR RNI

Figure 6

Connecting CAN At The End Of The Network

NOTES:

1. 24 AWG min., 12 AWG max.

2. 15 ohms max. for CAN

network.

3. Use twisted pair or twisted

shielded pair.

4. Power limited to NFPA 70

per NEC 760.

5. Refer to NIC-C Installation

Instructions, P/N 315-

033240 for connection of

CAN–, CAN+.

6. Only 1 SCM-8 shown. SCM-

8, LCM-8, FCM-6, OCM-16,

SIM-16 all allowed.

7. All field wiring supervised.

P3 P4

CAN +

CAN –

SHIELD

FROM

PSC-12

TB1

C+

C–

CCL (SUPPLIED WITH THE RNI)

C+

C–

RNI

TB6

DO NOT

USE

DO NOT

USE

LCM-8

SCM-8

INSTALL

CAN TERMINATOR

P/N 110-134215

(SHIPPED WITH NIC-C)

MOUNT TO ID-MP

ON INNER DOOR

OF REMBOX2/4

†

Siemens Building Technologies

Fire Safety

P/N 315-033420-44

Figure 7

Connecting CAN In The Middle Of The Network

NOTES:

1. 24 AWG min., 12 AWG max.

2. 15 ohms max. for CAN

network.

3. Use twisted pair or twisted

shielded pair.

4. Power limited to NFPA 70

per NEC 760.

5. Refer to NIC-C Installation

Instructions, P/N 315-

033240 for connection of

CAN–, CAN+.

6. Only 1 SCM-8 shown. SCM-

8, LCM-8, FCM-6, OCM-16,

SIM-16 all allowed.

7. All field wiring supervised.

P3 P4

CAN + CAN –

CAN – CAN +

SHIELD SHIELD

FROM

PSC-12

TB1

TO NEXT

RNI

C+

C–

CCL*

*ONLY 1 CCL, P/N 599-634214 IS SUPPLIED WITH THE RNI

C+

C–

RNI

TB6

LCM-8

SCM-8

MOUNT TO ID-MP

ON INNER DOOR

OF REMBOX2/4

†

Connecting The Optional Connect the HTSW-1 (required for UL1076) to P6 on the RNI using the connector

supplied with HTSW-1. Refer to the REMBOX Installation Instructions, P/N 315-

033772 and the HTSW-1 Installation Instructions, P/N 315-033350.

Connecting The Mount the LCM/SCM/FCM to the ID-MP (Refer to the LCM/SCM/FCM Installation

Instructions, P/N 315-033040). Mount the ID-MP to the inner door of the REMBOX2/4.

Connecting The Mount the SSD-C-REM to the inner door of the REMBOX2/4. Using the 8-wire cable

supplied with the SSD-C-REM, connect the SSD-C-REM to P2 on the RNI.

HTSW-1 Tamper Switch

LCM/SCM/FCM

SSD-C-REM

Siemens Building Technologies

Fire Safety

P/N 315-033420-45

tnerruCenalPkcaBV42*.xaMAm57

tnerruCV42lanimreTwercS0

tnerruCenalPkcaBV2.60

tnerruCybdnatSV42*.xaMAm57

lanimretwercsCDV42ehtedulcnioteruseB.ylnotnerrucINR*

gnimrofrepnehwseludomNACdnaTENHrehtollaroftnerruc

.snoitaluclacyrettabrosnoitaluclacgnidaolylppusrewop

POST-INSTALLATION Before applying power to the RNI check the following:

• Ensure that the 24VDC power input on TB1 is connected and that the

polarity is correct.

• Check the setting of S1. If the RNI is at the end of the HNET is must be set

to on. If the RNI is in the middle of the HNET it must be set to off. If the

HNET is not used the position of S1 does not matter.

• Check the position of P5. It must be set to H.

• Check the CAN termination. If the RNI is at the end of the CAN network, a

CAN terminator (P/N110-134215, supplied with the NIC-C) must be installed

into the last CAN module in the REMBOX.

If the RNI is in the middle of the CAN network no CAN terminators can be

installed. If CAN is not used then the terminator can be stored in P4. It will

be needed if CAN modules are added to the REMBOX at a later time. Refer

to the NIC-C Installation Instructions P/N 315-033240 for examples of CAN

installation and termination.

• Check the setting of P7. If the local sound is required, make sure P7 is set to

ON. Otherwise, set it to OFF.

COMPATIBILITY The RNI is compatible with the FireFinder XLS HNET and CAN networks only. The RNI

can not be used with the MXL MNET.

ELECTRICAL RATINGS

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN P/N 315-033420-4

Siemens Gebäudesicherheit

GmbH & Co. oHG

D-80930 München

For CE applications in Cerberus E100 systems refer to

Installation Instruction A24205-A334-B844 (English) or A24205-A334-A844 (German).

Inhaltsverzeichnis

Andere Siemens Aufnahmegeräte Handbücher

Siemens

Siemens XTRI-S Bedienungsanleitung

Siemens

Siemens N148/23 Bedienungsanleitung

Siemens

Siemens DLC Bedienungsanleitung

Siemens

Siemens SITOP PSU6200 Gebrauchsanweisung

Siemens

Siemens 538-907 Bedienungsanleitung

Siemens

Siemens SENTRON 7KN POWERCENTER 3000 Bedienungsanleitung

Siemens

Siemens 3RX9501-1BA00 Bedienungsanleitung

Siemens

Siemens SIMATIC RTLS4040T Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens D2300CPS Bedienungsanleitung

Siemens

Siemens WEBUI Bedienungsanleitung

Siemens

Siemens SIMATIC HMI KP400 Comfort Bedienungsanleitung

Siemens

Siemens Netzteil 3 A Bedienungsanleitung

Siemens

Siemens SIMATIC HMI KTP700F Mobile Bedienungsanleitung

Siemens

Siemens SIPLUS CMS4000 ION BINARYINPUT T001 Bedienungsanleitung

Siemens

Siemens 2D-TZ577 Bedienungsanleitung

Siemens

Siemens Albatros2 RVA78.690 Bedienungsanleitung

Siemens

Siemens TC35 Benutzerhandbuch

Siemens

Siemens NET-7 Bedienungsanleitung

Siemens

Siemens VDO DTCO 1381 Stücklistenhandbuch

Siemens

Siemens SIMATIC KTP400 Basic Bedienungsanleitung

Siemens

Siemens AEK84 Bedienungsanleitung

Siemens

Siemens 6AT8000-1BB00-0XA0 Bedienungsanleitung

Siemens

Siemens ASM 456 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch