Siemens DB-HR Bedienungsanleitung

P/N 315-033220-5

DETECTOR AND BASE PLACEMENT

Detector and base locations shall follow the drawings provided or approved

by Siemens Industry, Inc. or its authorized distributors.This is extremely

important! The detector placements shown on these drawings were chosen

after a careful evaluation of all facets of the protected area. When drawings

are not available, refer to Detector Placement section of detector Installation/

Wiring Instructions and to NFPA 72, National Fire Alarm Code and CAN/ULC-

S524.

BASE WIRING

The Model DB-HR from Siemens Industry, Inc. is a polarity insensitive detector

base and works with HFP-11, HFPT-11, HFPO-11, SFP-11*, SFPT-11* and SFPO-

11* detectors only. Detectors should be interconnected as shown in Figure 1

and wired to the DLC (refer to DLC Installation Instructions, P/N 315-033090), FS-

DLC (refer to FS-250 Installation, Operation and Maintenance Manual, P/N 315-

049353) or FDLC (refer to FS-250C Installation, Operation and Maintenance

Manual, P/N 315-049589C), as applicable. Line 1 and Line 2 can be either line of

the loop. Note any limitations on the number of detectors and restrictions

on the use of remote devices permitted for each circuit.

Figure 1

DB-HR Wiring Diagram Using HFP-11 Series and SFP-11 Series Detectors

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

*THE RELAY CONTACTS ARE

SHOWN IN THE NON-ALARM/

SYSTEM RESET CONDITION.

LINE 1 AND LINE 2 CAN BE EITHER LINE OF THE LOOP.

DO NOT USE AN END

OF LINE DEVICE

TO NEXT DEVICE

DO NOT USE AN END

OF LINE DEVICE

TO NEXT DEVICE

TO INITIATING CIRCUIT

OF SIEMENS INDUSTRY,

INC. CONTROL PANEL

REMOTE RELAY BASE

MODEL DB-HR

LINE 1

LINE 2

LINE 1

LINE 2

RELAY*

CONTACTS

3A, 120 VAC

3A, 30 VDC

DB-HR RELAY BASE

Detector Base

Installation Instructions

Model DB-HR

*SFP-11, SFPT-11 and SFPO-11 detectors are approved for use in Canada only.

DETECTOR MOUNTING USING THE DB-HR BASE

The detector is provided with a separate base which attaches to a standard 4

inch square or a 4 inch octagonal electrical box, with the box size and depth

required by the NEC for the number and size of conductors used. Wire size:

max – 14 AWG, min – 18 AWG.

Refer to Figure 2.

1. Route all wires outward from outlet box.

2. When the ALARM LED viewing is critical, position the LED mark in the

base in the intended direction.

3. Route wires through the hole in the center of the base and mount base

to outlet box. Make connections directly to the base terminals. Refer to

Figures 1 and 2 for details.

4. After all bases are installed, check wiring integrity.

5. To insure proper installation of the detector head into the base:

a. Route wires away from connector terminals.

b. Take up all slack in the outlet box.

c. Properly dress and position all wires flat against the base.

d. Check that screw terminals are tight.

P/N 315-033220-5

Figure 2

Mounting the Base

BASE

MOUNTING

HOLES

MOUNTING

HOLE COVERS

ALARM LED

LOCATION WITH

DETECTOR

INSTALLED

IN BASE

Inhaltsverzeichnis

Andere Siemens Sicherheitssensor Handbücher

Siemens

Siemens FDOOTC241 Bedienungsanleitung

Siemens

Siemens 5SM6011-1 Bedienungsanleitung

Siemens

Siemens Sinteso FD20 Bedienungsanleitung

Siemens

Siemens FDOOTC241 Bedienungsanleitung

Siemens

Siemens HI320C Bedienungs- und Montageanleitung

Siemens

Siemens FDOOTC441 Bedienungsanleitung

Siemens

Siemens FDOOT441 Bedienungsanleitung

Siemens

Siemens FDOOT271 Bedienungsanleitung

Siemens

Siemens DF11 Series Bedienungsanleitung

Siemens

Siemens DB721 Bedienungsanleitung

Siemens

Siemens Cerebrus Pyrotronics SA-11P Bedienungsanleitung

Siemens

Siemens FDO421 Bedienungsanleitung

Siemens

Siemens 7MH7701-0AA00-0A Bedienungsanleitung

Siemens

Siemens UP 255D21 5WG1 255-2DB21 Service-Handbuch

Siemens

Siemens HI921 Bedienungsanleitung

Siemens

Siemens DB721 Bedienungsanleitung

Siemens

Siemens DB720 Bedienungsanleitung

Siemens

Siemens GAMMA instabus AP 251/11 Service-Handbuch

Siemens

Siemens DB-11 Bedienungsanleitung

Siemens

Siemens FDT421 Bedienungsanleitung

Siemens

Siemens FDBH291 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RK3 Benutzerhandbuch

Siemens

Siemens SO320 Bedienungsanleitung

Siemens

Siemens FS720 Series Kurzanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung

Solinst

Solinst 301 Bedienungsanleitung