Siemens Synco QFP910 Bedienungsanleitung

CE1N2732en

18.05.2010

Building Technologies

2732

Synco™ living

Water detector QFP910

•Wireless radio sensor to record water puddles

•RF communication based on KNX standard (868 MHz unidirectional)

•Battery operation with standard 1.5 V batteries

Use

•Integrates into Siemens system Synco living

•Records water puddles in wet rooms, e.g. kitchens, bathrooms, laundry rooms, etc.

•Allows the following actions depending on how the central apartment unit is

configured:

−Automatically close the shutoff valve for the main line

−Activate interior siren

−Sends an alarm via web on a PC or cell phone

•Deployed especially for:

−The renovation market (old buildings, museums, churches, historical buildings, etc.)

−Difficult wall mounting (sandstone, glass, etc.)

−New buildings

2 / 8

Siemens Water detector QFP910 CE1N2732en

Building Technologies 18.05.2010

Equipment combinations

The QFP910 can be used together with the Siemens System Synco living. Detailed

information on the device combinations is available in the data sheet for the central

apartment unit.

Ordering

When ordering, please specify the quantity, product name, and type code.

The QFP910 consists of a water sensor and a radio transmitter.

Each QFP910 is delivered with alkaline batteries, mounting materials and mounting

instructions.

Type Stock number Name

QFP910 S55371-C100 Water detector with installation

instructions

Product documentation

Operating and commissioning instructions for the QFP910 are included in the product

documentation for the central apartment unit.

Functions

During normal operation, the QFP910 sends periodically, or for change its status (dry /

water leak), to the central apartment unit.

It interprets a "water leak" if the water sensor resistance drops below the lower limit

value and the corresponding message is sent to the central apartment unit.

The status for the QFP910 returns to "dry" if the resistance returns above the upper

limit value and a corresponding message is once again sent to the central apartment

unit.

The state "water leak" is sent at one-minute intervals.

The state "dry" is sent at 15-minute intervals.

Binding logs the QFP910 on to the central apartment unit and thus integrates it into the

radio system. The function button triggers the binding process. The function LED

signals the process.

The function button can query the battery level. The function LED signals the battery

level. It is also sent in each telegram to the central apartment unit.

The function button can trigger a binding test. This checks the radio link to the central

apartment unit. The function LED signals the RF binding test.

The maintenance message (batteries low) is forwarded to the central apartment unit

and displayed there.

The water sensor cannot be checked for short circuits or interrupts.

As a consequence, there are no error messages for a short circuit or sensor interrupt.

Delivery

Order numbers

Main function

Binding

Status request

RF binding test

Error messages /

Maintenance

messages

3 / 8

Siemens Water detector QFP910 CE1N2732en

Building Technologies 18.05.2010

The QFP910 generates the following messages:

Error messages Maintenance message

None Batteries low

(battery life ≤3 months)

Operating and display elements

Function

button

Function LED

Overview of display and operating element functions on the QFP910:

Function LED Function button

•Battery level

•Binding process

•Battery query

•Binding

•RF binding test

Additional information on the function and operation of the QFP910 is available in the

product documentation for the central apartment unit.

Notes on engineering and operation

•Mount the water sensor in the building

where there is water.

•The water sensor should be installed as

close as possible to any potential water

leak, e.g. in the laundry room, close to

the washer or in the kitchen below the

sink connections or input/output on the

dish washer.

•The water sensor should be mounted on

the wall at the lowest point so that the

two contacts nearly touch the floor.

•The floor under the water sensor should

be horizontal and even.

2732Z03

•Observe permissible ambient conditions.

•The water sensor should not be located in water puddles for longer periods as this

reduces battery life for the radio components.

Mounting location for

water sensor

4 / 8

Siemens Water detector QFP910 CE1N2732en

Building Technologies 18.05.2010

•Mount the RF transmitter in the building.

•Mount it close to the water sensor at a maximum of 1.8 meters above it (water sensor

cable length = 2 meters).

•Do not expose to drips and permissible ambient conditions must be maintained.

•Notes on engineering and mounting RF devices for the Siemens system Synco living

are available in the communications data sheet CE1N2708en.

•Mount the RF transmitter's wall base on a flat wall.

•Maintain a minimum distance of 60 mm from the bottom to open the battery

compartment.

≥60

2701Z03

Mount the RF transmitter using a base on the wall.

The RF transmitter can be mounted in most off-the-shelf recessed conduit boxes or

directly on the wall.

First mount the water sensor and then the RF transmitter. Then connect the water

sensor to the RF transmitter. Only then insert the batteries in the RF transmitter.

Prior to commissioning, check whether the water sensor is professionally installed at

the recommended location and in the proper position on the wall.

Further, check whether the connecting cable is professionally connected to the

corresponding terminals on the RF transmitter and whether functioning batteries are

properly inserted in the RF transmitter.

The QFP910 is maintenance free.

The system reports when a change of batteries is required. The batteries are located

under the cover for the battery compartment. No tools are required and batteries can be

changed in a mounted device (reverse battery protection).

You may have to clean the contact surfaces on the water sensor with a moist towel

after the water detector reacts and the water puddle is dried out. It may trigger a "water

leak" message. The message must then be acknowledged on the central apartment

unit.

RF Transmitter

mounting location

Mount

Note

Commissioning

Maintenance /

Change battery

5 / 8

Siemens Water detector QFP910 CE1N2732en

Building Technologies 18.05.2010

The QFP910 is considered electronics device for disposal in terms of European

Directive 2002/96/EG (WEEE) and may not be disposed of as domestic garbage.

Comply with all relevant national and statutory regulations. Dispose of the device via

the proper channels. Observe all local and applicable laws. Dispose of used batteries at

the collection locations provided.

Warranty

Technical data relating to applications are guaranteed solely together with the Siemens

Synco living system. Device combinations are available in the data sheet for the central

apartment unit.

The user ensures the functionality of operation for the QFP910 when using third-

party devices. Siemens does not provide service or guarantee services in this

case.

Disposal

6 / 8

Siemens Water detector QFP910 CE1N2732en

Building Technologies 18.05.2010

Technical data QFP910 – Water sensor

Cable length 2 m

Detector response time ≤2 seconds

Technical data QFP910 – RF transmitter

Battery type 2 x alkaline batteries LR6 (AA); 1.5 V

Battery life (capacity ≥2.5 Ah) 3 years (in "dry" state)

Radio Frequency 868 MHz, unidirectional

RF Range Typically 30 meters inside building

RF protocol KNX RF compatible

Screw terminals for cross-section of 0.1…1.5 mm2(connections interchangeable)

Cable length Max. 10 meters

Conformity to

EMC directive

- Immunity to interference, emissions

Low voltage directive

- Electrical safety

RTTE (Radio & Telecom. Equipment

- Radio communications

2004/108/EC

- EN 60730-1

2006/95/EC

- EN 60730-1

1999/5/EC

- EN 300220-2, EN 301489-1, EN 301489-3

Protection class III as per EN 60730

Housing IP40

2) as per EN 60529

Degree of pollution 2 as per EN 60730

The product environmental declaration

CE1E2732en contains data on

environmentally compatible product design

and assessments (RoHS compliance,

materials composition, packaging,

environmental benefit, disposal)

ISO 14001 (Environment)

ISO 9001 (Quality)

SN 36350 (Environmentally compatible

products)

RL 2002/95/EC (RoHS)

Refer to dimensions

Device packaged with inserts 0.28 kg

Plastic ASA+PC

White NCS S 0502-G

2) Fully mounted

Operation

EN60721-3-3

Transport

EN60721-3-2

Storage

EN60721-3-1

Environmental conditions Class 3K5 Class 2K3 Class 1K3

Temperature 0… +50 °C -25… +70 °C -20… +65 °C

Humidity 5…95 % r.h.

(non-condensing) <95 % r.h. 5…95 % r.h.

Mechanical conditions Class 3M2 Class 2M2 Class 1M2

Maximum elevation above sea level Min. 700 hPa corresponds to a maximum

of 3,000 meters above sea level

Water sensor

Power supply

Electrical connection

Standards

Degree of protection

Environmental

compatibility

Dimensions

Weight

Housing material

Housing color

mbient conditions

7 / 8

Siemens Water detector QFP910 CE1N2732en

Building Technologies 18.05.2010

Connection diagram

Water sensor

RF transmitter

Connections are interchangeable

Dimensions

Dimensions in mm

Water sensor

2000

3,4

2732M01

RF Transmitter

22 mm

76 mm

84 mm

2701M01a

84 mm

1 mm

28 28

TOP

42 42

4,2

4242 2702M01

8 / 8

Siemens Water detector QFP910 CE1N2732en

Building Technologies 18.05.2010

2010 Siemens Switzerland Ltd Subject to change

Inhaltsverzeichnis

Andere Siemens Sicherheitssensor Handbücher

Siemens

Siemens QRB Series Bedienungsanleitung

Siemens

Siemens AP 251/11 Service-Handbuch

Siemens

Siemens FDOOT221 Bedienungsanleitung

Siemens

Siemens FDL241-9 Bedienungsanleitung

Siemens

Siemens FDF241-9 Bedienungsanleitung

Siemens

Siemens DELTA reflex 5TC7 2 Series Service-Handbuch

Siemens

Siemens Intrunet IS392 Bedienungsanleitung

Siemens

Siemens 5SV6 Bedienungsanleitung

Siemens

Siemens SLD4 Beilage

Siemens

Siemens Intrunet IS390 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RK3 Benutzerhandbuch

Siemens

Siemens 5TC1700 Bedienungsanleitung

Siemens

Siemens Simotion TM 121C Gebrauchsanweisung

Siemens

Siemens FDT181 Bedienungsanleitung

Siemens

Siemens 667/HB/47200/000 Bedienungsanleitung

Siemens

Siemens CEREBRUS PYROTRONICS AD-3XRI Bedienungsanleitung

Siemens

Siemens FDOOTC241 Bedienungsanleitung

Siemens

Siemens QNA2 D Series Leitfaden

Siemens

Siemens 5SM6011-1 Bedienungsanleitung

Siemens

Siemens OH110 Bedienungsanleitung

Siemens

Siemens ADB-11 Bedienungsanleitung

Siemens

Siemens HI921 Bedienungsanleitung

Siemens

Siemens DB-HR Bedienungsanleitung

Siemens

Siemens Cerberus CS1140 Leitfaden

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung

Solinst

Solinst 301 Bedienungsanleitung