Siemens RDD10.1DHW Bedienungsanleitung

Operating Instructions RDD10.1DHW

RDD10.1DHW is a temperature controller that allows you to set the ideal room temperature at the

time you want and with independent control of DHW (Domestic Hot Water). There are 3 operating

modes available. You can either rely on the factory settings or make settings that suit your

personal needs.

Display Operation and settings

Warmer / colder

setting the

temperature setpoints

DHW ON/OFF

Changing the

operating mode

between normal

operation, energy

saving and frost

protection mode

Room temperature or setpoint

Batteries

3033Z05en

1.5V

'AA'

1.5V

'AA'

Normal operation

Energy saving mode

Heating ON

Room temperature

Replace batteries

DHW equipment ON

Frost protection mode

Commissioning

The controller is supplied with factory-set temperatures and operating mode. To commission

it, proceed as follows:

1,5 V

"AA"

1,5 V

"AA"

Remove the black transit tabs from the 2 batteries. Check to see if the battery holder

is in its correct position. The controller switches itself on.

Do you want to change the operating mode?

By pressing , you can change the operating

mode. The sequence is started from normal operation,

energy saving mode and frost protection, or vice versa.

Then, the setpoint of the selected operating mode will

be maintained.

In normal operation, the display shows , in energy

saving mode, the display shows , and in frost

protection mode, the display shows .

Default operating mode is “Normal operation”.

When the unit is first powered up,

the display shows .

Are your rooms too warm or too cold?

To increase or decrease the room temperature

setpoint in increments of 0.5 °C, proceed as follows:

•Press to select the operating mode

corresponding to the set point that you want to

change

•Press

+or once

The setpoint display starts flashing

•Press these buttons again to change the

temperature setpoint in the range 5 ... 35 °C

5 seconds after the last push, the new temperature

setpoint will automatically be saved. The display stops

flashing and shows the room temperature currently

measured.

Note:

The setpoint in energy saving mode can be set to

0 °C. This means OFF or, in other words, the

controller is not active in energy saving mode and

symbol will not appear on the display.

Risk of frost!

If you want to have frost protection, press to

select frost protection mode, the display shows

and default value is 5 °C. If the room temperature falls

below the preset frost protection level, it will

automatically activate the heating output.

CE1B3033en / 18.11.2005 Subject to alteration Building Technologies / HVAC Products

Energy saving tips without sacrificing comfort

•Never allow room temperatures to exceed 21 °C

•Press to change to energy saving or frost protection mode, even if

you are absent for short periods of time only

•Air out the rooms for short periods of time only, but properly, with the

windows wide open

Do you want to switch on DHW heating?

•Press to switch on DHW heating

•When DHW heating is switched ON, the display shows the symbol

•When pressing once again, DHW heating will be switched OFF and the

displays will not show the symbol

Does the symbol appear on the display?

1.5V

'AA'

1.5V

'AA'

When this symbol appears, you need to replace the batteries within the following

2 weeks.

Do you want to change the batteries?

•Get 2 new alkaline batteries type AA, 1.5 V

•Remove the battery holder, then the batteries, insert the new batteries and

replace the battery holder

•Make certain the old batteries are disposed of properly, in compliance with

environmental requirements

Recalibrating the sensor

If the room temperature displayed by the controller does

not match the temperature effectively measured, the

temperature sensor can be recalibrated.

Follow the steps below to recalibrate the sensor:

1. In normal operation, press the “+” and operating mode

changeover buttons simultaneously for more

than 3 seconds, switching the system to calibration

mode.

2. The display format in calibration mode is the same as in

normal or energy saving mode, but with the temperature

digits flashing at 1Hz. You can adjust the temperature to

the desired value with the “+” or “-” button at 0.5 K per

step. The maximum adjustable range is +/- 3 K.

3033Z01

3. If no button is pressed for 5 seconds, the system will

return to the initial operating mode and the temperature

is set to the new value.

Note that the operating mode changeover and DHW

buttons are deactivated in calibration mode.

CE1B3033en / 18.11.2005 Subject to alteration Building Technologies / HVAC Products

Andere Siemens Temperaturregler Handbücher

Siemens

Siemens REA23.03RF Bedienungsanleitung

Siemens

Siemens 2000 Series Bedienungsanleitung

Siemens

Siemens SITRANS T Series Administratorhandbuch

Siemens

Siemens POS8.4420/109 Bedienungsanleitung

Siemens

Siemens Landis & Staefa REV11 Series Bedienungsanleitung

Siemens

Siemens RDE10.1DHW Bedienungsanleitung

Siemens

Siemens QAA73 Bedienungsanleitung

Siemens

Siemens RDD310 Bedienungsanleitung

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens 2200 Series Bedienungsanleitung

Siemens

Siemens TALON Bedienungsanleitung

Siemens

Siemens REA22 Bedienerhandbuch

Siemens

Siemens HZ39050 Bedienungsanleitung

Siemens

Siemens RDF30U Betriebsanleitung

Siemens

Siemens RVL482 Bedienungsanleitung

Siemens

Siemens UP 237K Bedienungsanleitung

Siemens

Siemens RCC10U Betriebsanleitung

Siemens

Siemens Synco 900 Leitfaden

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens QAA24 Bedienungsanleitung

Siemens

Siemens QAX30.1 Bedienungsanleitung

Siemens

Siemens QAA70 Bedienungsanleitung

Siemens

Siemens 1000 Series Bedienungsanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema