Siemens REV23.03RF Bedienungsanleitung

CE1N2265en

22.02.2006

Building Technologies

HVAC Products

2265

REV23.03RF REV-R.03/1

REV23RF/SET

Self-learning Room

Temperature Controller REV23.03RF

Receiver REV-R.03/1

Consisting of controller (with integrated radio transmitter) and receiver

(switching unit with relay outputs)

•Mains-independent room temperature controller

•Straightforward, self-explanatory menu selection via roller selector

•Self-learning 2-position controller providing PID mode (patented)

•Choice of operating modes:

Automatic with maximum 3 heating or cooling periods, continuously comfort,

continuously economy, frost protection with one 24-hour operating mode including

one heating or cooling period

•In automatic mode, one temperature setpoint can be entered for each heating or

cooling period

•Optional control of cooling equipment

•Advantageous for retrofitting and upgrading projects

(wireless room unit)

Use

For control of the room temperature in:

•Apartments, single-family or holiday houses

•Offices, individual rooms, consulting rooms or commercially used spaces

For control of the following pieces of equipment:

•Solenoid valves of instantaneous water heaters

2/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

•Solenoid valves of atmospheric gas burners

•Forced draft gas or oil burners

•Circulating pumps of heating systems, zone valves

•Electric direct heating systems or fans of electric storage heaters

•Thermal actuators

•Cooling and refrigeration equipment

Functions

•Radio signal transmission

•PID control with self-learning or selectable switching cycle

•2-position control

•Automatic mode with 7-day switching program for 24-hour, working day, weekend or

7-day operation with up to 3 heating or cooling periods per day

•Each heating or cooling period has its own temperature setpoint

•One 24-hour operating mode with one heating or cooling period

•Override button

•Sensor calibration and reset function

•Frost protection or overtemperature protection

•Limitation of the minimum setpoint

•Holiday mode

•Heating or cooling mode

•Periodic pump run

•Optimum start control with the first heating period

Type summary

Radio signal equipment consisting of:

Room temperature controller (transmitter), receiver (switching unit)

and support REV23RF/SET

Room temperature controller (transmitter) and support REV23.03RF

Receiver (switching unit) REV-R.03/1

Ordering

When ordering, please give the type references according to «Type summary».

The controller / transmitter REV23.03RF is supplied complete with batteries.

Technical design

Display and

operating elements

3/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

Operating elements

Selection of operating mode (see below)

«Warmer» button

«Colder» button

Override button (see below)

Roller selector for the menu, submenu and the settings

Confirm by pressing

Leaving the current menu level and returning to the menu level

previously active (settings currently displayed will be ac-

cepted)

Displays

Time of day

° C

Room temperature

Change batteries (display appears about 3 months before bat-

teries are exhausted)

Holiday mode active

Selection of operating mode (only one operating mode active)

Automatic mode

Comfort mode

Economy mode

Frost protection or overtemperature protection

24-hour mode with one heating or cooling period

(heating or cooling period is individually adjustable)

Temporary change of the current setpoint temperature

(change only active until the next switching point is reached)

° C

Press the + or – button once to display the adjusted tempera-

ture setpoint. It can be readjusted in increments of 0.2 °C (max.

+/- 4 °C)

Override button

In operating modes and , this button can be used to manually switch

from comfort to economy temperature, or vice versa. The selection is automati-

cally reset when the next switching point is reached or when the operating

mode is changed

4/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

Menu-driven user settings: 4 main menus are available

Time of day and weekday Main menu Submenu Settings

hCurrent time

Current weekday

Temperature Main menu Submenu Default settings – heating / cooling

T Setpoint of comfort mode 19 °C 23 °C

Setpoint of economy mode 16 °C 29 °C

Setpoint frost or

overtemperature protection 5 °C 35 °C

Setpoint remote operation is

not used with this unit (10 °C) (30 °C)

Time switch Main menu Submenu Settings

Selection of weekday, working day,

weekend or week

Selection of the number of heating

or cooling periods (max. 3 periods

per day)

Selection of the heating / cooling period’s start and end time

° C

Selection of the heating / cooling period’s temperature setpoint

Absence Main menu Submenu

Entry of holidays or periods of absence. Number

of days with economy mode setting / max. 99

days

Temperature setpoint during absence.

Default setting is 12 °C for heating and 30 °C for

cooling

5/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

Menu-driven heating

engineer settings Menu items Settings

CAL Sensor calibration

Setpoint limitation

Optimum start control for the first heating period

(in unit of time per 1 °C)

2-position control

PID mode, self-learning

PID mode, switching cycle 6 or 12 minutes

/Periodic pump run off / on

Heating / cooling mode

In automatic operating modes, the temperature setpoints can be individually adjusted

for every comfort period and for the continuous operating modes. The temperature

setpoint of economy mode is the same in automatic and continuous operation.

In frost or overtemperature protection mode, the room temperature is constantly moni-

tored. If it falls (rises) below (above) the adjusted setpoint, control to the adjusted frost

or overtemperature protection setpoint will be ensured.

The controller operates in 24-hour operating mode according an individually adjustable

24-hour program with 1 heating / cooling period.

To adjust heating / cooling period, select 24-hour operating mode and adjust time pro-

gram and desired temperature setpoint by roller selector.

24-hour operating mode is maintained until another operating mode is selected.

The switching program can be used as a 7-day or 24-hour program, depending on

programming. It is also possible to select one of the continuous operating modes

with which the switching program is not used.

With the 7-day program, all individual days, working days (1-5), weekend (6-7), or the

entire week (1-7) can be programmed.

For each heating / cooling period, 3 different switching patterns are available.

There is a choice of 1, 2 or 3 heating / cooling periods. For each heating / cooling pe-

riod, the start time, end time and comfort setpoint are to be entered.

In between heating / cooling periods, it is always the same economy temperature set-

point that is used. This economy temperature setpoint can be adjusted on the tempera-

ture menu.

Temperature

setpoints

Protective function

24-hour operating

mode

Switching program

6/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

2261Z02

°C

08 10 18 22 h

Heizphase 1

Heizphase 2

The holiday function is to be selected on the user menu. Set the start of the holiday

period (day of departure / /weekday), the duration of the holiday period and

the temperature setpoint ( ). This will enable the controller to maintain the adjusted

temperature for a period of up to 99 days. Every day at midnight, the counter subtracts

one day.

When the holiday period is over, the counter reads 00, and the controller will automati-

cally resume the operating mode selected last.

To be flexible, the REV23.03RF has no connection facility for remote operation.

Switching times Temperatures in ° C

1st

period

2nd

period

3rd

period

Oper-

ating

mode

Block /

week-

days 1st period 2nd period 3rd period

Auto

1-5

Mo-Fr

6-7

Sa-Su

06:00

07:00

08:00

23:00

11:00

13:00

17:00

22:00

1-7

Mo-Su 00:00 24:00 19 23

1-7

Mo-Su 00:00 24:00 16 29

1-7

Mo-Su 00:00 24:00 5 35

1-7

Mo-Su 07:00 23:00 19 23

Absence 12 30

Setpoint limitation

Control mode 2-Point control

Optimum start control OFF

Periodic pump run OFF

Heating active

Example with 2 heating

periods per day

Holiday function

Remote operation

Factory settings

Heating engineer level

7/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

Heating engineer level

To access the heating engineer level, keep the «Warmer» and «Colder» buttons de-

pressed and simultaneously roll the roller selector away from the display and then to-

ward the display.

If the displayed temperature does not agree with the room temperature effectively

measured, the temperature sensor can be recalibrated (recalibration to be made on the

heating engineer level.)

The displayed temperature can be matched to the effective room temperature in incre-

ments of 0.2 °C (max. ± 2 °C).

Minimum setpoint limitation to 16 °C prevents undesired heat transfer to neighboring

apartments in buildings with several heating zones. The setting is to be made on the

heating engineer menu.

Optimization brings forward the switch-on point of the first heating period such that the

adjusted setpoint will be reached at the required time.

The setting depends on the type of controlled system, that is, on heat transmission

(type of piping system, radiators), building dynamics (building mass, insulation), and

heat output (boiler capacity, flow temperature).

Optimum start control is switched off at

- 4 - 2

2264D03

- 3

1/4h/°C

1/2h/°C

1h/°C

Start

- 2 - 1 - ½

- 1½

- 1 - ½ - ¼

- ¾

Pon

°C

- 1 h

TRx

1st heating period

(slow controlled system)

(medium controlled system)

(fast controlled system)

(no impact)

Optimum start controll Off

T Temperature (°C) TRxActual valve of room temperature

t Forward shift of switch-on point (h) Pon Starting point of optimum start control

REV23.03RF is a 2-position controller providing PID mode. The room temperature is

controlled by the cyclic switching of an actuating device.

The controller generates the positioning signals depending on the deviation of the set-

point from the actual value acquired by the built-in temperature sensor.

The rate of response to the deviation depends on the selected control algorithm:

The controller is supplied with an active self-learning mode, enabling it to automatically

adapt to the type of controlled system (building construction, type of radiators, size of

the rooms, etc.). After a certain learning period, the controller optimizes its parameters

and then operates with the parameters it has learned.

PID 12 mode Switching cycle of 12 minutes for normal or slow controlled systems

(massive building structures, large spaces, cast-iron radiators, oil

burners).

PID 6 mode Switching cycle of 6 minutes for fast controlled systems (light building

structures, small spaces, plate radiators or convectors, gas burners).

2-Pt mode Pure 2-position control with a switching differential of 0.5 °C (±0.25 °C)

for very difficult controlled systems with considerable outdoor tempera-

ture variations.

For easy commissioning controller is set to 2-Point mode as factory

setting.

Access

Sensor calibration

CAL

Setpoint limitation

Optimum start control

Example using an actual

room temperature of 18 °C

and a setpoint of 20 °C

Control

Self-learning mode

8/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

Protects the pump against seizing during longer off periods. Periodic pump run is acti-

vated for one minute every 24 hours at midnight. This function can be selected on the

heating engineer menu.

Periodic pump run active: / periodic pump run inactive:

The controller is suited for cooling applications.

The function can be selected on the heating engineer menu.

The controller comes set for heating operation (refer to section «Factory settings»).

User-defined data:

Press the button behind the pin opening for at least one second: This resets the user-

specific settings to their default values (heating engineer settings will not be changed).

The clock starts at 12:00. During the reset time, all sections of the display are lit, ena-

bling them to be checked.

All user-defined data plus the heating engineer settings:

Press the button behind the pin opening together with the warmer and colder buttons

for at least one second.

After the reset, all factory settings will be reloaded (also refer to section «Factory

settings»).

Mechanical design

The REV23.03RF has a plastic housing with a large display and easily accessible op-

erating elements. The controller is removed from its base by sliding it upward. It is thus

possible to replace the two type AA 1.5 V alkaline batteries contained in the compart-

ment at the rear of the controller.

About 3 months before the batteries are exhausted, battery symbol appears on

the display, but all functions are fully maintained. When replacing the batteries, the

current data will be retained for a maximum of one minute.

Plastic housing with easily accessible operating elements and removable cover. The

unit can be fitted to all commercially available recessed conduit boxes or directly on the

wall. A relay with a potential free changeover contact, the connection terminals and the

receiving antenna are integrated in the housing.

The base can be fitted to most types of commercially available recessed conduit boxes

or directly on the wall.

The support supplied with the controller enables the unit to be put on a shelf. It can be

easily fitted to the controller with no need for tools.

Periodic pump run

Operating mode

Heating / cooling

Controller

Battery change

Receiver

REV-R.03/1

Base

Support

9/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

Notes

•The room unit should be located in the main living room (on the wall or free-standing

using the support provided) while giving consideration to the following points:

•The distance to the receiver should not exceed 20 m or 2 floors

•The unit should be located such that the sensor is able to capture the room tempera-

ture as accurately as possible, without getting affected by direct solar radiation or

other heat or refrigeration sources (in the case of wall mounting, about 1.5 m above

the floor)

•The unit should be located such that it can transmit signals with as little interference

as possible. For this reason, the following points should be observed:

−Do not mount the unit on metal surfaces

−Not in the vicinity of electrical cables and equipment such as PCs, TV sets, mi-

crowave appliances, etc.

−Not in the vicinity of large metal structures or construction elements with fine

metal meshes like special glass or special concrete

•The control mode can be changed via the menu-driven heating engineer settings.

•If the room temperature displayed does not agree with the room temperature effec-

tively measured, the temperature sensor should be recalibrated (refer to «Calibration

of sensors»).

•In the case of wall mounting, ensure that there is sufficient clearance for removing the

controller from its base, and for replacing it

First, fit the base. Then, engage the controller from the top. The base can be fitted to

most commercially available recessed conduit boxes or directly on the wall

min.

10 cm

2261Z03

•Refer to the Installation Instructions printed on the package.

•The receiver and switching unit should preferably be mounted near the controlled

device

•The unit should be located such that it can receive signals with as little interference

as possible. For this reason, the following points should be observed (same as with

the transmitter):

−Not in control panels

−Not on metal surfaces

−Not in the vicinity of electrical cables and equipment such as PCs, TV sets, mi-

crowave appliances, etc.

−Not in the vicinity of large metal structures or construction elements with fine

metal meshes like special glass or special concrete

•The location where the unit is mounted should be dry and free from splash water

•The unit can be fitted to most commercially available recessed conduit boxes or di-

rectly on the wall

Planning

controller / transmitter

REV23.03RF

Wall mounting of

controller / transmitter

REV23.03RF

Support of

REV23.03RF

Planning

Receiver

REV-R.03/1

10/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

The receiver must be wired with the power supply switched off.

Mains voltage may be switched on again only after the unit is completely

mounted.

•When mounting the unit, the base must first be fitted and wired (L/N = AC 230 V

mains supply, LX/L1 = consumers). Then, engage the unit at the top, swing it down-

ward and secure it with a screw

•For more detailed information, refer to the Installation Instructions supplied with the

unit

For the electrical installation, the local safety regulations must be complied with.

•Remove the battery transit tab: As soon as the battery transit tab is removed, the

unit starts to operate.

•If possible, mount receiver temporarily in a first run (e.g. double coated tape). Doing

that, location of best RF reception can be identified later on. See clause “5 Find lo-

cation of best reception“

•Completely wire and mount REV-R.03/1 temporarily (please also close front cover)

a) Switch on power at REV-R.03/1: LED_1 lights always in red or flashes in red

b) Press the "RESET“ button on REV-R.03/1 for about 4 seconds: The orange LED_2

will flash very fast and briefly (stored address of REV23.03RF will be erased)

c) Press the "SET“ button (set / learn) for about 3 sec. until the orange LED_2 starts

flashing slowly and continuously: Receiver is now in learning mode

d) The receiver stays max. 25 minutes in learning mode. If no learning telegram from

REV23.03RF is received during that period of time, repeat steps b) and c) again

e) Press the ESC button on REV23.03RF for about 4 seconds. Learning tele-

gram is transmitted

f) If REV-R.03/1 receives learning telegram, the orange LED_2 flashes fast and

briefly

g) If the orange LED_2 is steady on, the relay is energized (= controlled device ON)

h) If the orange LED_2 is dark, the relay is deenergized (= controlled device OFF)

i) Depending on the operating state, REV23.03RF repeats the ON or OFF control

telegram every 3 minutes. With this the relay will be switched ON or OFF according

to control telegram latest after 3 minutes

j) If REV-R.03/1 does not receive any correct control telegram within 60 minutes,

controlled device is being switched off and LED_1 flashes in red

k) In the event of a power failure at the REV-R.03/1, the relay will be deenergized.

Mounting and

installation of receiver

REV-R.03/1

Commissioning

controller/transmitter

REV23.03RF

and receiver

REV-R.03/1

1. Switch on

REV23.03RF

2. Mount REV-R.03/1

temporarily

3. Link REV-R.03/1

with REV23.03RF

Override button and

test telegram

ESC button and

learnin

tele

ram

LED_1 (green / red):

Indication for

- Signal strength

- Receiver linked to

cotroller/transmitter

LED_2 (orange):

Indication for

- Learning mode

- Telegram reception

- Status of relais contact

SET button

RESET button

Andere Handbücher für REV23.03RF

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Temperaturregler Handbücher

Siemens

Siemens QMX3.P37 Bedienungsanleitung

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens Landis & Staefa RAV12 Series Bedienungsanleitung

Siemens

Siemens RCU50U Betriebsanleitung

Siemens

Siemens RDU20U Bedienungsanleitung

Siemens

Siemens SITRANS TS100 Administratorhandbuch

Siemens

Siemens POS8.4420/109 Bedienungsanleitung

Siemens

Siemens 2200 Series Bedienungsanleitung

Siemens

Siemens RLM162 Bedienungsanleitung

Siemens

Siemens REV23RF16A Bedienungsanleitung

Siemens

Siemens i-system UP 237K Service-Handbuch

Siemens

Siemens RLA162 Bedienungsanleitung

Siemens

Siemens RLE162 Bedienungsanleitung

Siemens

Siemens RDH10RF/SET Bedienungsanleitung

Siemens

Siemens UP 237K Bedienungsanleitung

Siemens

Siemens QAA24 Bedienungsanleitung

Siemens

Siemens SITRANS TSinse rt Administratorhandbuch

Siemens

Siemens RDE series Bedienungsanleitung

Siemens

Siemens RDU50U Betriebsanleitung

Siemens

Siemens RDJ10RF/SET Bedienungsanleitung

Siemens

Siemens RLA162 Bedienungsanleitung

Siemens

Siemens RCC30 Bedienungsanleitung

Siemens

Siemens Free Energy Band RCU61U Betriebsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Bedienungsanleitung

Vaillant

Vaillant VR 92/3 Bedienungsanleitung