Siemens RDH10RF/SET Bedienungsanleitung

CE1B3070en / 01.03.2010 Subject to alteration Siemens Building Technologies / HVAC Products

Operating instructions RDH10RF/SET

RDH10RF/SET consists of a RDH10RF wireless temperature controller and a RCR10/433 receiver. The RDH10RF

allows you to set the desired room temperature (setpoint) at the time you want. The unit features an ergonomic

setting knob for ease of temperature control.

Display

Actual room temperature in ºC

The unit is controlling to the selected

comfort temperature

Indicates when there is demand for

heat

Replace batteries

TEST

Appears on the screen when the

transmitter is being tested.

Setting knob

Warmer/colder knob for

selecting the temperature

setpoint

Battery compartment

Two alkaline batteries type AA, 1.5 V

Commissioning before start-up

Commissioning

•Remove the black transit tabs from the alkaline batteries.

•Check to see if the battery holder is in the correct position.

•If no batteries are inserted, fit 2 alkaline batteries type AA in the battery compartment.

Initial power-up

Once batteries are fitted, all symbols will appear on

the display as shown for about two seconds.

Selecting the required temperature

•Turn the setting knob counter clockwise to

decrease the setpoint, or clockwise to increase the

setpoint in increments of 0.5 °C

•The required temperature is displayed next to

the comfort temperature symbol

Changing the batteries

1. Get two new batteries of type AA alkaline, 1.5 volts.

2. Remove the battery holder, then the batteries, insert new batteries and

replace the battery holder.

The old, set values must be checked!

3. Make certain the old batteries are disposed of properly, in

compliance with environmental requirements.

Energy saving tips without sacrificing comfort

●Never allow room temperatures to exceed 21˚C.

●Air out rooms: Air out rooms for short periods with open windows and

doors.

CE1B3070en / 01.03.2010 Subject to alteration Siemens Building Technologies / HVAC Products

NOTE:

You can press the OVERRIDE button on the receiver to manually switch ON/OFF for a faulty

room unit or transmission protocol.

NOTE:

You must re-execute the workflow for commissioning the set to reestablish a connection between

the room controller and receiver .

Front View Receiver

LED Signal Indicator LED Relay Indicator

Orange LED indicates relay is on.

The signal is good when the

LED flashes green.

A flashing red LED indicates

that there is no signal. OVERRIDE Button

Press this button to overwrite transmitter

values.

RESET: Press the LEARN & OVERRIDE

button for 4 seconds to delete all transmitter

addresses.

LEARN Button

Rear View Room Unit

(Transmitter)

Press the button to learn a transmitter

address.

Learn Button TEST Button

Release learn telegram Used for testing transmission.

Front View Receiver

Configuration instructions for the Siemens RDH10RF/SET

The Transmitter RDH10RF and the receiver RCR10/433 are set to communicate (bonded) with each

other at the factory. If they fail it is necessary to re bond the units due to loss of communication please

follow the following instructions.

1. Reset receiver by simultaneously pressing the LEARN & OVERRIDE button for 4 seconds.

2. Press and release the LEARN button. This set the receiver to learn mode.

3. Press and release the LEARN button on the back of the transmitter.

4. A green flashing or solid LED indicates a good signal, a red flashing or solid LED indicates no

signal.

5. To test transmission, press the TEST button on the transmitter, switches the relay on in

the receiver regardless of temperature. The RF TEST symbol appears on the thermostat display.

6. An orange LED indicates that the relay is on.

Andere Handbücher für RDH10RF/SET

Andere Siemens Temperaturregler Handbücher

Siemens

Siemens UP 237K Bedienungsanleitung

Siemens

Siemens 2200 Series Bedienungsanleitung

Siemens

Siemens QAA73 Bedienungsanleitung

Siemens

Siemens SITRANS Series Administratorhandbuch

Siemens

Siemens SIMATIC Bedienungsanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Siemens

Siemens BPS242RF Bedienungsanleitung

Siemens

Siemens AVS13.399 Bedienungsanleitung

Siemens

Siemens 5TC9774-5 Series Bedienungsanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Siemens

Siemens QAW910 Bedienungsanleitung

Siemens

Siemens QMX3.P37 Bedienungsanleitung

Siemens

Siemens HZ39050 Bedienungsanleitung

Siemens

Siemens RDX42.22U Betriebsanleitung

Siemens

Siemens 1000 series Bedienungsanleitung

Siemens

Siemens REA23.03RF Bedienungsanleitung

Siemens

Siemens RLE162 Bedienungsanleitung

Siemens

Siemens RDF210 Bedienungsanleitung

Siemens

Siemens QAA70 Bedienungsanleitung

Siemens

Siemens Free Energy Band RCU61U Betriebsanleitung

Siemens

Siemens QAA2290.EWSC Bedienungsanleitung

Siemens

Siemens RDD310 Bedienungsanleitung

Siemens

Siemens REA22 Bedienerhandbuch

Siemens

Siemens REV23.03RF Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema