Siemens 2200 Series Bedienungsanleitung

Installation Instructions

Document No. 129-104

October 1, 2013

Series 2200 Relative Humidity and

Temperature Room Units For

APOGEE® Controllers

Page 1 of 5

Product Description

These room units measure relative humidity and

temperature in the occupied space in which they are

installed. Models with display allow users to view the

measured temperature value. A version with

temperature setpoint adjustment is also offered.

These devices are intended for use with appropriate

signal input on an APOGEE Controller. The effective

sensing range is 32°F to 122°F (0°C to 50°C), and

the setpoint range is 55°F to 95°F (13°C to 35°C).

These room units can be mounted on electrical

boxes, stud-type mounting brackets, or drywall.

Obtain the necessary mounting hardware and follow

the appropriate mounting procedures for the type of

installation required.

Product Numbers

QFA3212.FWSN QFA32SS.FWSN

QFA3212.EWSN QFA32SS.EWSN

Accessories

AQA2200-INTL Room Unit Back Plate

(10-pack)

AQA2200-2X4 Room Unit Back Plate

(Single)

563-102 GSKT Kit Room Sensor Insulating

Gasket (10-pack)

(For hollow wall installations)

NOTE: If installing the Back Plate, discard the

metric screws provided with the Back Plate

and utilize the Room Unit mounting screws.

Caution Notations

CAUTION Equipment damage or loss of

data may occur if you do not

follow a procedure as

specified.

Item Number 129-104, Rev. HA

Expected Installation Time

20 minutes

Required Tools

•Sizes 1 and 2 Phillips screwdrivers

•Small and medium flat-blade screwdrivers

•1/16-inch hex key

•Medium-duty electric drill

•3/16-inch (4.8 mm) drill bit

•One-inch (25 mm) hole saw

•Small level

•Tape measure

•Marker or pencil

Prerequisites

•Review these instructions before beginning.

•Installed: appropriate field wiring within the

maximum wiring run length for the individual

equipment controller. The maximum

recommended length is 750 feet (229 m) for

18 AWG; 300 feet (91 m) for 22 AWG.

•All wiring must comply with National Electric

Code (NEC) and local regulations.

Figure 1. Typical Temperature Room Unit.

Document No. 129-104

Installation Instructions

October 1, 2013

Page 2 of 5 Siemens Industry, Inc.

Mounting Information

Always mount the room unit vertically.

Locate the room unit:

•according to design specifications and local

regulations.

•where the air circulates around it freely (not in

recessed areas or behind doors).

•allowing a minimum of 4 inches (10 cm) free

space above and below for proper airflow, the

front cover removal tool, and the computer

communication cable.

•away from drafts caused by doors, windows,

outside walls, air registers, pipes, return air

plenums, etc.

•away from heat sources such as strong lights,

fireplaces, direct sunlight, etc.

•on an inside wall (preferably), about 5 feet

(1.5 m) above the finished floor.

Drywall Mounting (No Rough-in),

Typical

Base Plate Mounting and Wiring

1. Mark the center (cable) hole and the mounting hole

locations, using the room unit base plate as a

template. See Figure 3.

2. Drill two 3/16-inch (4.8 mm) mounting holes and

mount the two plastic wall anchors flush to below the

wall surface for stable mounting of the device.

3. Cut a 1-inch (25 mm) center hole with a hole saw.

NOTE: It is recommended that you use the

optional Insulating Gasket on the back of

the Sensor Base for hollow wall

installations.

When applying the adhesive-backed

gasket to the back of the Sensor Base,

orient the gasket so that the cut-out

arrow portion of the gasket is in the

upper lefthand quadrant of the Sensor

Base. The Sensor Base has an UP arrow

molded into the surface in the same

quadrant location (see Figure 6).

Figure 2. Insulating Gasket.

4. Pull about three inches (75 mm) of the cable through

the hole in the base plate.

5. Mount the room unit base plate on the wall, noting

the UP arrow:

NOTE: If required, position the Back Plate

behind the Room Unit Base, aligning the

top and bottom mounting holes, prior to

mounting to the wall:

a. Install the two mounting screws provided, but

do not tighten.

b. Level the room unit base plate for appearance.

c. Tighten the two mounting screws to the room

unit base plate.

6. Cut the cable, leaving about three inches (75 mm)

on the room unit side of the drywall. Ensure that pin

Number 1 connects to the same wire at each end of

the cable.

NOTE: See Figure 2 for details on optional Gasket

application.

Figure 3. Drywall Mounting (No Rough-in), Typical.

Document No. 129-104

Installation Instructions

October 1, 2013

7. Terminate the wires to the termination blocks on the

room unit's base plate. (See Figure 6.)

8. Feed the extra cable back through the hole.

Sensor Set-up

SEN0589R1

10V

Jumper

R64 Resistor

(°F/°C Selector)

Voltage/Current

Selector Switch

Figure 4. Circuit Board

(Located inside Room Unit Cover.

1. If the device has a switch, determine if voltage or

current output is needed.

•For current, set the switch in the down position

(I).

•For voltage, set the switch in the up position (V).

NOTE: The output setting applies to all outputs

(humidity, temperature, and setpoint).

2. If selecting voltage, set the jumper:

•Use the top and middle pins for 0-5V.

•Use the bottom and middle pins for 0-10V.

NOTE: If the jumper is missing or removed, the

output voltage will default to

0-10V.

NOTE: The factory default for displayed temperature

units is °F. To change the display to °C, snip the

wire jumper (0 Ohm resistor R64) on the back of

the PCA.

SEN0588R1

Figure 5. Changing Display to °C.

3. Snap the room unit cover to the room unit base plate

by first hooking the room unit front to the top latches,

and then rotating the cover downward until it latches.

4. Loosen the safety set screw at the bottom of the

base one or two revolutions to lock the cover to the

base. Be careful not to loosen too far as the screw

can be completely removed from the base.

Electrical Box and Rough-in

Mounting, Typical

1. If a locator is attached to the rough-in device,

remove the locator by removing the two screws and

lightly rocking the locator to pull it free.

2. Untie the twist tie and pull about three inches (75

mm) of the room unit cable through the hole in the

base plate.

3. Mount the room unit base plate on the wall, noting

the UP arrow:

a. Install the two room unit mounting screws

provided, but do not tighten.

b. Level the room unit base plate for appearance

only.

c. Tighten the two mounting screws to the room

unit base plate.

CAUTION:

Over-tightening may cause the room unit

base plate to crack or bend.

4. Continue with Drywall Mounting (No Rough-in),

Typical, Steps 6 through 8, and Sensor Set-up.

Document No. 129-104

Installation Instructions

October 1, 2013

Page 4 of 5Siemens Industry, Inc.

SEN0485R1

CAUTION:

To prevent equipment damage, do the

following:

If room unit is powered by AC (See Figure

8.):

•AC Supply must be type NEC Class

2 and earth grounded at the

secondary neutral.

•Room Unit ACN (GND) must be

connected to the controller common.

•If the controller has a floating

common, that common must be

connected to the same earth ground

point as the controller AC supply.

If room unit is powered by isolated DC

(See Figure 7):

•Where power is current limited up to

300 mA, it is not required to earth

ground the controller isolated

common.

•Room Unit DC-(GND) must be

connected to the controller common.

Figure 6. Typical Wiring Base.

(All terminals may not be present.)

Pin No. Function

QFA3212.EWSN or QFA32SS.EWSN

1 DC+ or ACH

2 DC- or ACN (GND)

3 Temp Output

4 Humidity Output

5* Passive Temp

6* Passive Temp Common

QFA3212.FWSN or QFA32SS.FWSN

1 DC+ or ACH

2 DC- or ACN (GND)

3 Temp Output

4 Humidity Output

5* Passive Temp

6* Passive Temp Common

7 Setpoint Output

8 Override

9 Override Common

CAUTION:

Follow manufacturer’s Installation

Instructions and Wiring Guidelines for

connecting the controller to the Room

Unit.

•APOGEE Controllers with common

already earth grounded are TXIO used

on PXC Modular, PXC Compact 36

Expansion and P1 BIM or PTM used

on MBC and RBC. These do not

require the earth ground wire to be

connected to the controller as shown in

Figure 8.

•APOGEE Controllers with floating

common are PXC Compact 16/24/36,

MEC, PXM, LON TEC and PPM.

These require the earth ground wire to

be connected to the controller as

shown in Figure 8.

* Not available on “SS” models.

NOTE: If active temperature (0-5V/0-10V/4-20 mA)

(Pin 3) rather than passive/resistive temperature

is used, Passive Temp Common (Pin 6) does

not need to be terminated.

The installation is now complete.

Document No. 129-104

Installation Instructions

October 1, 2013

2200

DC+ ACH

DC- ACN (GND)

Signal Out

CONTROLLER

Sensor Power DC

Common

Signal In

Common

Signal In

SEN0650R1

Isolated DC

Supply 300 MA Max.

DC+

DC-

Controller

See Controller

Installation Instructions

For Power Input

Requirements

2200

DC+ ACH

DC- ACN (GND)

Signal Out

Isolated DC

Figure 7. Externally DC Powered 2200 Room Units.

2200

DC+ ACH

DC- ACN (GND)

Signal Out

CONTROLLER

Sensor Power DC

Common

Signal In

Common

Signal In

Common

Signal In

Common

Signal In

SEN0649R1

Class 2

Isolated AC Supply

100 VA Max.

Class 2 (100VA)

Isolated AC

ACH

ACN

ACH

ACN

ACH

ACN

Controller

2200

DC+ ACH

DC- ACN (GND)

Signal Out

2200

100 VA

DC+ ACH

DC- ACN (GND)

Signal Out

Class 2 (100VA)

Isolated AC L N E

With Class 2 (100 VA) Output

Isolated AC Supply

(See Controller

Installation Instructions)

L N E

Note: See Caution

Figure 8. Externally AC Powered 2200 Room Units.

NOTE:

Externally DC powered

2200 Room Units require

isolated DC supply with all

commons connected and

may be used on the same

controller with other Room

Units powered by Internal

Sensor Supply.

NOTE:

Externally AC powered

2200 Room Units require

controller common and all

AC secondary neutral ACN

to be earth grounded and

may be used on the same

controller with other room

units powered by internal

sensor supply.

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as

design improvements are introduced. APOGEE is a registered trademark or Siemens Industry, Inc. Other product or company names mentioned herein

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089

USA

+ 1 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.[email protected]

Document No. 129-104

Printed in the USA

Page 5 of 5

Inhaltsverzeichnis

Andere Siemens Temperaturregler Handbücher

Siemens

Siemens REV24RF Montageanleitung

Siemens

Siemens 2000 Series Bedienungsanleitung

Siemens

Siemens REV15 series Bedienungsanleitung

Siemens

Siemens SITRANS TS100 Administratorhandbuch

Siemens

Siemens RDF20U Bedienungsanleitung

Siemens

Siemens SITRANS TSinse rt Administratorhandbuch

Siemens

Siemens Polygyr-Compact Betriebsanleitung

Siemens

Siemens i-system UP 237K Service-Handbuch

Siemens

Siemens RCC30 Bedienungsanleitung

Siemens

Siemens RLM162 Bedienungsanleitung

Siemens

Siemens REV24 Bedienungsanleitung

Siemens

Siemens 5TC9774-4 Series Bedienungsanleitung

Siemens

Siemens SITRANS Series Administratorhandbuch

Siemens

Siemens RVL482 Bedienungsanleitung

Siemens

Siemens RLA162 Bedienungsanleitung

Siemens

Siemens RCC10U Betriebsanleitung

Siemens

Siemens KIT911 Gebrauchsanweisung

Siemens

Siemens RDD10.1DHW Bedienungsanleitung

Siemens

Siemens RLE132 Bedienungsanleitung

Siemens

Siemens Landis & Staefa REV11 Series Bedienungsanleitung

Siemens

Siemens RAV12 series Bedienungsanleitung

Siemens

Siemens RDX Series Bedienungsanleitung

Siemens

Siemens RCU50U Betriebsanleitung

Siemens

Siemens REV23 Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema