Siemens SIMATIC WinCC V11 Benutzerhandbuch
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the relevant information is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Ⓟ 05/2012 Technical data subject to change
Copyright © Siemens AG 2012.
All rights reserved
Table of contents
1 Security note.................................................................................................................................................5
2Special considerations for Windows 7..........................................................................................................7
3Installation.....................................................................................................................................................9
4Runtime......................................................................................................................................................11
4.1 Notes on operation in Runtime....................................................................................................11
4.2 Notes on operation of Runtime Advanced...................................................................................12
4.3 Communication............................................................................................................................13
Index...........................................................................................................................................................15
Readme WinCC Runtime Advanced V11 SP2 Second Edition
System Manual, 03/2012, 3
Security note 1
Security information
Siemens offers IT security mechanisms for its portfolio of automation and drive products in
order to support secure operation of the plant/machine. Our products are also continuously
developed further with regard to IT security. We therefore recommend that you keep yourself
informed about updates and upgrades for our products and always use the latest version of
each product. For information on this topic, refer to: http://support.automation.siemens.com
(http://www.siemens.de/automation/csi_en_WW) You can register for a product-specific
newsletter here.
For the safe operation of a plant/machine, however, it is also necessary to integrate the
automation components into an overall IT security concept for the entire plant/machine which
corresponds to the state-of-the-art IT technology. You can find information on this under:
http://www.siemens.com/industrialsecurity. (http://www.siemens.com/industrialsecurity)
Products used from other manufacturers should also be taken into account here.
Readme WinCC Runtime Advanced V11 SP2 Second Edition
System Manual, 03/2012, 5
Special considerations for Windows 7 2
Contents
Information that could not be included in the online help.
Permission for the starting Runtime
To start WinCC Runtime Professional or WinCC Runtime Advanced, a user must be a member
of the automatically created group, "Siemens TIA Engineer".
Working with standard user rights
If you are working with standard user rights in Windows 7, "User Account Control (UAC)" cannot
be disabled.
The "User Account Control" is enabled in Windows 7 by default.
For more information on the "User Account Control, refer to the online help for Windows 7.
Slow response from the screen keyboard and SmartServer
The following programs may start and respond very slowly under Windows 7 and Windows
2008 servers:
● Microsoft OSK screen keyboard and HMI TouchInputPC
● SmartServer: <Ctrl+Alt+Del> shortcut in the logon dialog
The delay is caused by the callback for the Internet certificate validation.
Remedy:
Locate the following files on the product DVD under:
Support\Windows7\CRL_Check or CD_RT\ Support\Windows7\CRL_Check\
:
● DisableCRLCheck_LocalSystem.cmd
● DisableCRLCheck_CurrentUser.cmd
1. Run the "DisableCRLCheck_LocalSystem.cmd" file with administrator rights. Select the
command "Run as administrator" from the shortcut menu of the file.
2. Reboot the PC.
If the problem persists, follow these steps:
Readme WinCC Runtime Advanced V11 SP2 Second Edition
System Manual, 03/2012, 7
1. Double-click the file and run the "DisableCRLCheck_CurrentUser.cmd" file with user rights.
2. Reboot the PC.
NOTICE
The callback for the certificate validation is disabled for all users or PCs. To restore the
original state, perform the following files:
●RestoreDefaults_LocalSystem.cmd
● RestoreDefaults_CurrentUser.cmd
You can find the files in the following directory of product DVD:
● Support\Windows7\CRL_Check bzw. CD_RT\Support\Windows7\CRL_Check\
Special considerations for Windows 7
Readme WinCC Runtime Advanced V11 SP2 Second Edition
8System Manual, 03/2012,
Installation 3
Contents
Information that could not be included in the online help.
Parallel installation of WinCC V11 and other SIMATIC HMI products
The parallel installation of WinCC V11 with versions of WinCC flexible prior to WinCC flexible
2008 is not permitted.
The parallel installation of WinCC V11 with versions of WinCC prior to WinCC V7.0 SP2 is not
permitted. The parallel installation of WinCC V11 with WinCC V7.0 SP2 or WinCC V7.0 SP3
is only permitted for:
● WinCC V11 Basic
● WinCC V11 Runtime Advanced
Parallel installations in the TIA portal
You will be prevented from starting the TIA portal if you perform a non-permitted parallel
installation of STEP 7 and WinCC.
The following parallel installations are permitted in the TIA portal:
● STEP 7 V11 and WinCC V11
● STEP 7 V11 SP1 and WinCC V11 SP1
● STEP 7 V11 SP1 with WinCC V11 SP2
● STEP 7 V11 SP2 and WinCC V11 SP1
● STEP 7 V11 SP2 with WinCC V11 SP2
A dialog opens during installation to inform you of any inconsistencies in your parallel
installation.
The following parallel installations are permitted:
● WinCC V11 and RT Advanced V11
● WinCC V11 SP1 and RT Advanced V11 SP1
● WinCC V11 SP2 and RT Advanced V11 SP2
The engineering system and Runtime must always be of the same version after an installation.
Operating system message for SIMATIC USB drivers
An operating system message relating to the SIMATIC USB driver is issued on the operating
system Windows Server 2003 R2 StdE SP2.
This message must be acknowledged with "Yes" as soon as possible after the message has
been issued. The message may be in the background and therefore not be immediately visible.
Readme WinCC Runtime Advanced V11 SP2 Second Edition
System Manual, 03/2012, 9
After a certain period of time, the setup continues with the next component. The SIMATIC USB
drivers are then not installed and can not be used.
Installation
Readme WinCC Runtime Advanced V11 SP2 Second Edition
10 System Manual, 03/2012,
Andere Handbücher für SIMATIC WinCC V11
1
Inhaltsverzeichnis
Andere Siemens Touchscreen Handbücher
Siemens
Siemens Desigo Touch Series Installations- und Betriebshandbuch
Siemens
Siemens SIMATIC Panel PC IL 77 Bedienungsanleitung
Siemens
Siemens SIMATIC TP900 Comfort INOX PCT Administratorhandbuch
Siemens
Siemens 6AV3991-1AJ02-0AB0 Technisches Dokument
Siemens
Siemens SIMATIC HMI series Bedienungsanleitung
Siemens
Siemens 670 V2 Bedienungsanleitung
Siemens
Siemens UP 588/12 Bedienungsanleitung
Siemens
Siemens Panel PC 670 Technisches Dokument
Siemens
Siemens SIMATIC PC 670 Technisches Dokument
Siemens
Siemens SIMATIC INOX Series Administratorhandbuch
Siemens
Siemens SIMATIC IPC677D Bedienungsanleitung
Siemens
Siemens 270 series Bedienungsanleitung
Siemens
Siemens SIMATIC Panel PC IL 77 Bedienungsanleitung
Siemens
Siemens Climatix POL8T1.4X/STD Bedienerhandbuch
Siemens
Siemens POL8T5.70/STD Bedienerhandbuch
Siemens
Siemens Simatic PC Panel PC 870 Technisches Dokument
Siemens
Siemens 5WG1205-2AB21 Bedienungsanleitung
Siemens
Siemens Climatix POL8T2.70/STD Bedienerhandbuch
Siemens
Siemens SIMATIC WinCC V11 Benutzerhandbuch
Siemens
Siemens SIMATIC 677 Bedienungsanleitung
Beliebte Touchscreen Handbücher anderer Marken
IBASE Technology
IBASE Technology ASTUT-152-RE1S Bedienungsanleitung
YASKAWA
YASKAWA TP 610C Bedienungsanleitung
B&R
B&R Power Panel C Series Bedienungsanleitung
Beijer Electronics
Beijer Electronics X2 control Bedienungsanleitung
AXIOMTEK
AXIOMTEK GOT321W-521 Bedienungsanleitung
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Bedienungsanleitung
