Siemens FT2080 Leitfaden

FT2080

Fire terminal (Touch)

Mounting

Installation

A6V10462660_en--_b

Building Technologies

2016-04-08 Control Products and Systems

Legal notice

2 | 24

Building Technologies

A6V10462660_en

Fire Safety

2016

Legal notice

Technical specifications and availability subject to change without notice.

Transmittal, reproduction, dissemination and/or editing of this document as well as

utilization of its contents and communication thereof to others without express

authorization are prohibited. Offenders will be held liable for payment of damages.

All rights created by patent grant or registration of a utility model or design patent

are reserved.

Issued by:

Siemens Switzerland Ltd.

Building Technologies Division

International Headquarters

Gubelstrasse 22

CH-6301 Zug

Tel. +41 41 724-2424

www.siemens.com/buildingtechnologies

Edition: 2016-04-08

Document ID: A6V10462660_en--_b

3 | 24

Building Technologies

A6V10462660_en

Fire Safety

2016

Table of contents

1Setup of fire terminal (Touch) FT2080.....................................................5

2Installation in 19" pedestal housing of the FC2080....................................7

3Installation in housing (standard).......................................................... 10

4Installation in rear panel (FT2080) FHA2039.......................................... 11

5Installation in desktop housing (FT2080) FHA2040................................. 16

6Technical data.................................................................................... 22

Building Technologies

A6V10462660_en

Fire Safety

2016

4 | 24

Setup of fire terminal (Touch) FT2080

5 |

Building Technologies

A6V10462660_en

Fire Safety

2016

1Setup of fire terminal (Touch) FT2080

Figure 1: Rear panel fire terminal (Touch) FT2080

1 Support plate

2 Front indicator (Touch) FTO2010

3 PMI & mainboard FCM2027

4 4x mounting holes in the operating unit

5 Shield plate above carrier (CPU)

6 Hinges for wall housing

Setup o

f fire terminal (Touch) FT2080

6 | 24

Building Technologies

A6V10462660_en

Fire Safety

2016

Arrangement of components

Figure 2: Components on the fire terminal (Touch) FT2080, without cover cap

1 Front indicator (Touch) FTO2010

2 Main network module (SAFEDLINK) on X13, optional

3 License key, optional

4 Slot 1 [SER_OPT1] for the first serial module at X14, optional

5 Slot 2 [SER_OPT2] for the second serial module at X19, optional

6 Degraded mode network module (SAFEDLINK) on X12, optional

7 CPU module (CORVUS) FCC2009

8 Carrier for CPU modules FTO2014

9 CPU module (MPC8248) FCC2006

10 PMI & mainboard FCM2027

11 Slot X11 for serial module. Not required for FT2080

Both slots X14 and X19 can hold the RS232 or RS485 serial

module.

Installation in 19" pedestal housing of the FC2080

7 |

Building Technologies

A6V10462660_en

Fire Safety

2016

2Installation in 19" pedestal housing of the

FC2080

The installation instructions described below apply to all operating units.

Before an operating terminal is installed, the following components must first be

mounted on the operating unit.

●Network module (SAFEDLINK) FN2001-A1 with ES ≥12, for connecting to the

FC2080

●Adapter and connection cable for the power supply

–Supplied with processor unit (19", FC2080) FCC2002-A1

Preparing the operating unit

The network module (SAFEDLINK) FN2001-A1 must be installed on connector

X13 of the operating unit (main module slot).

Figure 3: Installing the required components, taking operating unit FCM2028-A1 as an example

1 Operating unit

2 Flange with threaded holes for securing the module

3 Connector strip X13 for network module

4 Network module (SAFEDLINK) FN2001-A1 with ES ≥12

Installation in 19" pedestal housing of the FC2080

8 | 24

Building Technologies

A6V10462660_en

Fire Safety

2016

5 2x fixing screw

6 PMI & mainboard FCM2027

7 Adapter for power supply (including ribbon cable)

8 Connector strip X3 peripheral data bus connection

1. Plug the network module (SAFEDLINK) (4) into connector X13 (3) of the

operating unit (1).

2. Secure the module to mounting flange (2) with both screws (5). Ensure that it is

secured correctly to avoid interrupts.

3. Plug the adapter (7) into connector X3 (8) of the PMI & mainboard (6) so

inscription 'TOP' is at the top.

Installing operating unit

Figure 4: Mounting operating terminal in door, taking operating unit FCM2028-A1 as an example

1 Inside of door

2 Opening for operating unit

3 4x welded threaded bolts

4 4x mounting holes in the operating unit

5 4x fixing screws

1. Remove the cover plate (2) by removing the four nuts (5).

2. Place the mounting holes (4) of the operating unit on the four threaded bolts (3)

and screw the operating unit down with the four nuts (5).

3. The operating add-ons in the bottom window openings are installed in the

same way.

4. Wire up the operating unit and operating add-ons according to the following

wiring instructions.

12 3

Installation in 19" pedestal housing of the FC2080

9 |

Building Technologies

A6V10462660_en

Fire Safety

2016

Wiring the fire terminal (Touch)

Figure 5: Wiring the fire terminal (Touch) with FC2080

1 Ribbon cable for FC2080 system supply to card cage (CPU) X30

2 FCnet connection to card cage (CPU) X11/X12

3X3 connection to network module (SAFEDLINK) to PMI & mainboard

FCM2027

4 Inside of door (section view)

5 Fire terminal (Touch) FT2080

6 Adapter for flat cable of the supply

Figure 6: Example of FCnet wiring of X3 on PMI & mainboard FCM2027 of the fire terminal (Touch)

* The FCnet connection from X11 to X12 on the card cage (CPU) FCC2003 is

wired up in advance at the factory.

B2A2B1A1B2A2B1A1

1234 1234

X11

X12

1234

FCC2003

FCM20xx

FC2080

FCnet

FN2010 FN2010 FN2001

Door

Installation in housing (standard)

10 | 24

Building Technologies

A6V10462660_en

Fire Safety

2016

3Installation in housing (standard)

Figure 7: Installation of fire terminal in the housing (standard) FH2002

1 Mains connection terminals

2 Power supply unit (70 W) FP2015

3 Rear panel (standard)

4 Fire terminal board FTI2001

5 Wiring FCnet/SAFEDLINK

6 Network module (SAFEDLINK) FN2001

7 Fire terminal (Touch) FT2080

X3 Ribbon cable connection from the fire terminal (Touch) to the fire terminal

board

X1 Supply input for fire terminal board

You will find detailed information on wiring the 'fire terminal board FTI2001' and the

'network module (SAFEDLINK) FN2001' in document Product Data 008837.

Andere Handbücher für FT2080

Inhaltsverzeichnis

Andere Siemens Touch-Terminal Handbücher

Siemens

Siemens FT2015 Bedienungsanleitung

Siemens

Siemens SIMATIC NET Bedienungsanleitung

Siemens

Siemens SENTRON 3TW1CG20PT Bedienungsanleitung

Siemens

Siemens 3TA2JG600PT Bedienungsanleitung

Siemens

Siemens 3VL9400-8BH01 Bedienungsanleitung

Siemens

Siemens AlgoPilot B3Q661 Bedienungsanleitung

Siemens

Siemens VT9324-4TD30 Bedienungsanleitung

Siemens

Siemens 3VM9 0-0WC00 Series Bedienungsanleitung

Siemens

Siemens 3VA9 Series Bedienungsanleitung

Siemens

Siemens SINUMERIK HT 10 Technisches Dokument

Siemens

Siemens 3VT9203-4TF30 Bedienungsanleitung

Siemens

Siemens 3VT9100-4RC00 Bedienungsanleitung

Siemens

Siemens A5E01621433-01 Bedienungsanleitung

Siemens

Siemens 3NP1143 Bedienungsanleitung

Siemens

Siemens 3VF7 Bedienungsanleitung

Siemens

Siemens 8WH6000-0 0 Series Bedienungsanleitung

Siemens

Siemens SIMATIC HMI IPC477C PRO Bedienungsanleitung

Siemens

Siemens 3VT9400-4RC30 Bedienungsanleitung

Siemens

Siemens 3RK1922-3BA00 Bedienungsanleitung

Siemens

Siemens 3RV1 Bedienungsanleitung

Siemens

Siemens FT2080 Bedienungsanleitung

Siemens

Siemens SIMOTION TM15 Bedienungsanleitung

Siemens

Siemens 3UF1900-1KA00 Bedienungsanleitung

Siemens

Siemens SRTNF3 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung