SIGLENT SDS2352X-E Bedienungsanleitung

Trademark Information

SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.

Declaration

SIGLENT products are protected by patent law in and outside of the P.R.C.

SIGLENT reserves the right to modify or change parts of or all the specifications or

pricing policies at company’s sole decision.

Information in this publication replaces all previously corresponding material.

Any way of copying, extracting or translating the contents of this manual is not

allowed without the permission of SIGLENT.

Product Certification

SIGLENT guarantees this product conforms to the national and industrial standards

in China and other international standards. Conformance certification is in

progress.

If you have any problem or requirement when using our products, please contact

SIGLENT TECHNOLOGIES CO., LTD

Add：3//F, Bldg No.4, Antongda Industrial Zone, 3rd Liuxian Road, Bao’an District,

Shenzhen, 518101, P.R.China

Tel：400-878-0807

E-mail：sales@siglent.com

http://www.siglent.com

Introduction

This user manual includes important safety and installation information related to

the SDS2000X-E series oscilloscopes and includes simple tutorials for basic

operation of the oscilloscope.

The series includes the following models:

Model

Analog Bandwidth

SDS2352X-E

350 MHz bandwidth, 2-channel, 2 GSa/s Sample rate

SDS2202X-E

200 MHz bandwidth, 2-channel, 2 GSa/s Sample rate

SDS2102X-E

100 MHz bandwidth, 2-channel, 2 GSa/s Sample rate

Safety Information

Measurement Category

Measurement Categories

This oscilloscope can make measurements in other circuits that are not directly

connected to mains.

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Not to use the product for measurements within other measurement

categories, such as CAT II, CAT III, CAT IV.

Do not use the equipment for measurements on mains circuits.

Measurement Category Definitions

Measurement category II is for measurements performed on circuits directly

connected to the low voltage installation. Examples are measurements on

household appliances, portable tools and similar equipment.

Measurement category III is for measurements performed in the building

installation. Examples are measurements on distribution boards, circuit-breakers,

wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the

fixed installation, and equipment for industrial use and some other equipment, for

example. Stationary motors with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of the

low-voltage installation. Examples are electricity meters and measurements on

primary over current protection devices and ripple control units.

General Safety Summary

Carefully read the following safety precautions to avoid any personal injury or

damage to the instrument and any products connected to it. To avoid potential

hazards, please use the instrument as specified.

Use Proper Power Line

Only the power cord designed for the instrument and authorized by the local

country should be used.

Ground the Instrument

The instrument is grounded through the protective earth conductor of the power

line. To avoid electric shock, please make sure the instrument is grounded correctly

before connecting its input or output terminals.

Connect the Signal Wire Correctly

The potential of the signal wire is equal to the earth, so do not connect the signal

wire to a high voltage.

Look Over All Terminals’ Ratings

To avoid fire or electric shock, please look over all ratings and read the instructions

for the instrument. Before connecting the instrument, please read the manual

carefully to gain more information about important ratings.

Use Proper Overvoltage Protection

Make sure that no overvoltage (such as that caused by a thunderstorm) can reach

the product, or else the operator might expose to danger of electrical shock.

Electrostatic Prevention

Operate in an electrostatic discharge protective area environment to avoid

damages induced by static discharge. Always ground both the internal and

external conductors of the cable to release static before connecting.

Keep Well Ventilation

Inadequate ventilation may cause an increasing in operting temperature, which

will eventually damage the instrument. So keep well ventilation and inspect the

intake and fan regularly.

Avoid Circuit or Components Exposed

Do not touch exposed contacts or components when the power is on.

Use proper Fuse

Use only the specified fuse.

Do Not Operate Without Covers

Do not operate the instrument with covers or panels removed.

Do Not Operate With Suspected Failures.

If you suspect damage occurs to the instrument, have it inspected by qualified

service personnel before further operations. Any maintenance, adjustment or

replacement especially to circuits or accessories must be performed by SIGLENT

authorized personnel.

Do Not Operate in Wet Conditions.

In order to avoid short circuiting to the interior of the device or electric shock,

please do not operate in a humid environment.

Do Not Operate in an Explosive Atmosphere.

In order to avoid damages to the device or personal injuries, it is important to

operate the device away from an explosive atmosphere.

Keep Product Surfaces Clean and Dry.

To avoid the influence of dust and/or moisture in air, please keep the surface of the

device clean and dry.

Handling Safety

Please handle with care during transportation to avoid damaging buttons, knob

interfaces and other parts on the panels.

Only probe assemblies which meet the manufacturer’s specifications shall be used.

When using SIGLENT probe assemblies, the probe assemblies shall be insulated

from the measured circuits by double or reinforced insulation.

All probe assemblies should meet the requirements of UL 61010-031 and

CAN/CSA-C22.2 No. 61010-031-07.

Do not position the equipment so that it is difficult to disconnect an attached device

(detachable plug).

If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

Safety Terms and Symbols

Terms in this Manual. These terms may appear in this manual:

WARNING

Warning statements indicate the conditions or practices that

could result in injury or loss of life.

CAUTION

Caution statements indicate the conditions or practices that

could result in damage to this product or other property.

Terms on the product. These terms may appear on the product:

DANGER Indicates direct injuries or hazards that may happen.

WARNING Indicates potential injuries or hazards that may happen.

CAUTION Indicates potential damage to the instrument or other property that may

happen.

Symbols on the product. These symbols may appear on the product:

Hazardous protective Earth Warning Test Power Switch

Voltage Terminal Ground

If find such symbols on the product, consult the manual to find out the nature of the

potential hazard and the actions which have to be taken.

Working Environment

Environment

This instrument is intended for indoor use and should be operated in a clean, dry

environment.

Temperature

Operating: 0℃to +40℃

Non-operation:-20℃to +60℃

Note: Direct sunlight, radiators, and other heat sources should be taken into

account when assessing the ambient temperature.

Humidity

Operating: 85% RH, 40 ℃, 24 hours

Non-operating: 85% RH, 65 ℃, 24 hours

Altitude

Operating: less than 3 Km

Non-operation: less than 15 Km

Installation (overvoltage) Category

This product is powered by mains conforming to installation (overvoltage) category

II.

WARNING

Make sure that no overvoltage (such as that caused by thunderbolt) can

reach the product, or else the operator might expose to danger of

electric

shock.

Installation (overvoltage) Category Definitions

Installation (overvoltage) category I refers to signal level which is applicable to

equipment measurement terminals connected to the source circuit. In these

terminals, precautions are done to limit the transient voltage to the corresponding

low level.

Installation (overvoltage) category II refers to the local power distribution level

which is applicable to equipment connected to the AC line (AC power).

Degree of Pollution

The oscilloscopes may be operated in environments of Pollution Degree II.

Note: Degree of Pollution II refers to a working environment which is dry and

non-conductive pollution occurs. Occasional temporary conductivity caused by

condensation is expected.

IP Rating

IP20 (as defined in IEC 60529).

Ventilation Requirement

This oscilloscope uses a fan to force cooling. Please make sure that the air intake

and exhaust areas are free from obstructions and have free air. When using the

oscilloscope in a bench-top or rack setting, provide at least 10 cm clearance beside,

above and behind the instrument for adequate ventilation.

WARNING

Inadequate ventilation may cause temperature increase which would

damage the instrument. So please keep the instrument well ventilated

during operation and inspect the intake and fan regularly.

Andere Handbücher für SDS2352X-E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SIGLENT Messgerät Handbücher

SIGLENT

SIGLENT SHA852A Bedienungsanleitung

SIGLENT

SIGLENT SSA3050X-R Bedienungsanleitung

SIGLENT

SIGLENT SHA800A Bedienungsanleitung

SIGLENT

SIGLENT SSA3021X Bedienungsanleitung

SIGLENT

SIGLENT SSA5000A Bedienungsanleitung

SIGLENT

SIGLENT SHA850A Bedienungsanleitung

SIGLENT

SIGLENT SSA3000X-R Bedienungsanleitung

SIGLENT

SIGLENT SSA5085A Bedienungsanleitung

SIGLENT

SIGLENT SSA3000X Plus Bedienungsanleitung

SIGLENT

SIGLENT SSA3000X Plus Bedienungsanleitung

SIGLENT

SIGLENT SNA5000A Bedienungsanleitung

SIGLENT

SIGLENT SVA1075X Bedienungsanleitung

SIGLENT

SIGLENT CPL5100 Bedienungsanleitung

SIGLENT

SIGLENT SM06035-E01A Bedienungsanleitung

SIGLENT

SIGLENT SSA3000X Series Bedienungsanleitung

SIGLENT

SIGLENT SHS800X Series Bedienungsanleitung

SIGLENT

SIGLENT SP3150A Bedienungsanleitung

SIGLENT

SIGLENT SNA5000A Bedienungsanleitung

SIGLENT

SIGLENT SSA3075X Plus Bedienungsanleitung

SIGLENT

SIGLENT SVA1000X Series Bedienungsanleitung

SIGLENT

SIGLENT CP6000 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung