Sigma BC 14.12 ALTI Bedienungsanleitung

BIKE COMPUTER TOPLINE

VIdEO

TUTORIal:

InsTallaTIOn

VIdEO:

FUNCTIONS

SI GBBGRUSEDKFINO SK

BC 14.12 A LTI / BC 14.12 A LTI

Contents

1. Introduction to the BC 14.12 ALTI /

BC 14.12 STS ALTI 02

1.1 Initial use 02

1.2 Navigation principle 03

1.3 Set-up 04

2. Functions / Properties 04

2.1 General 04

2.2 Special functions 06

2.3 Altitude measurement 06

2.4 STS features 07

3. Settings / Deletion 09

3.1 Settings 09

3.2 Determining the wheel size 09

3.3 Deleting the functions 09

4. Important Notes / Troubleshooting 10

4.1 Technical data 10

5. Warranty Conditions 12

1. Introduction to the BC 14.12 ALTI / BC 14.12 STS ALTIENGLISH

You can find the CE declaration under:

www.sigmasport.com

1.1 Initial use

The bike computer comes in “deep sleep mode”.

To exit this mode, press and hold the MODE 1 and

SET buttons for five seconds.

On waking up, the bike computer

will be in active mode.

To access the settings,

press the SET button.

1.2.1 Button functions 1.2.2 Assigning the functions

1.2 Navigation principle

RESET button for

– Deleting the

current values

– Scrolling backward

You can access the following

functions by pressing the

MODE 2 button:

current altitude / trip altitude /

time / temperature /

total distance / total time /

total altitude

You can access the following

functions by pressing the

MODE 1 button:

trip distance / trip time /

Ø speed / max. speed

MODE 2 button for

– Switching between

several functions

– Scrolling forward

MODE 1 button for

– Switching between

the bike functions

– Scrolling forward

SET button for

– Switching to / from

the setting mode

– Scrolling backward

2.1 General

– Current / average speed comparison k

If you are traveling at approximately

your average speed, nothing is

displayed. If you are traveling

quicker than your average speed,

( ) is displayed; if you are

traveling slower ( ) is displayed.

This information is displayed in

almost all functions, except the

basic settings.

– Light manager kSimultaneously press the SET and

RESET buttons to switch the light function on / off.

The display lights up by pressing any button; the

bike computer changes to the respective function

when the button is pressed again. Avoid using the

backlight unnecessarily to save the battery!

1.3 Set-up

Please see the leaflet provided for the set-up

diagrams!

1.2.3 Display layout

2. Functions / Properties

Top field:

Speed

Middle field:

Description of the functions

Bottom field:

Current value

1.2 Navigation principle

2. Functions / Properties

– Service interval kThe service interval informs

you when you have cycled a specified number of

kilometers and a bike inspection is due. This service

interval can only be enabled/disabled and pre-

configured by your specialist retailer. The device

comes with the service interval disabled.

– Battery status kThe battery status of the computer

head unit is displayed shortly before the battery

runs out. “ low / computer” appears on the display.

After changing the battery, only the time needs to be

re-set.

– Memory chip kThanks to an inbuilt memory chip,

all total values and settings are permanently stored

in the bike computer. This means that you do not

need to reconfigure any settings (except for the time)

after changing the battery.

– PC compatibility kThe bike computer is

PC-compatible. After purchasing the SIGMA

DATA CENTER software and docking station,

you can simply and effortlessly log your total

and current values on your PC. You can also

configure your bike computer’s settings on

the PC.

www.sigma-data-center.com

2.3 Altitude measurement

The altitude measurement on the BC 14.12 ALTI /

BC 14.12 STS ALTI is determined on the basis of the

barometric air pressure. Any change to the weather

means a change to the air pressure, which can lead

to a change to your current altitude. To compensate

these changes in air pressure, you must enter a

reference altitude into the BC 14.12 ALTI /

BC 14.12 STS ALTI (process known as calibration).

– Calibration using the start altitude kThe start

altitude is the altitude of your usual start location

(generally your home). You can find this information

on road or country maps. It is set in the

BC 14.12 ALTI / BC 14.12 STS ALTI once and

calibrated within a matter of seconds.

2.2 Special functions

– Hiding total values during the trip k

If the BC 14.12 ALTI / BC 14.12 STS ALTI receives

speed signals, all the total functions (distance, time,

and cumulated altitude) are hidden on the display.

If no speed values are received, the functions

are once again displayed.

2. Functions / Properties

– Calibration using the current altitude kThe current

altitude is the altitude of the place at which you are

currently located irrespective of your start altitude

(your trip start location, a mountain hut, or other

locations). The current altitude is used if you are

out on your bike and altitude information is provided.

2.4 STS features

– Synchronization kAttach the BC 14.12 STS ALTI

to the bracket – zeros flash for the speed.

There are two ways of synchronizing the speed:

– 1. kStart cycling – the receiver usually

synchronizes with the transmitter after 3-4 wheel

rotations.

– 2. kSpin the front wheel until the speed values

stop flashing.

Removing the BC 14.12 STS ALTI from the bracket

severs the connection.

1 2

– Message “Too Many Signals” kIncrease your

distance from other cyclists (transmitters) and

press any button. Synchronization re-starts. (If the

transmission connection is lost during your trip and

no longer functions, press and hold the MODE 1

button for more than three seconds to start manual

synchronization. “Sync. RESET” flashes on the

display)

2. Functions / Properties

– Transport mode kWhen transported on a bike

rack or in the car (if clicked into the bracket),

the BC 14.12 STS ALTI switches to “transport

mode” via an integrated movement sensor.

“Transport” appears on the display.

Press any button to exit this mode.

> 3 sec.

3.3 Deleting the functions

Please see the diagrams for how to delete the

functions.

3. Settings / Deletion

3.1 Settings

The following settings can be configured: language /

unit / current altitude / start altitude / wheel size / time /

total distance / total time / total altitude / contrast.

Clear diagrams of how to set each of these functions

can be found in the enclosed leaflet.

3.2 Determining the wheel size

To measure your speed precisely, the wheel size must

be set on the basis of your tire size. To do this, you can:

A– Calculate the wheel size using the formula provided

in the wheel size chart.

B– Determine the value from the drawings in the

wheel size chart.

C– Take the value that corresponds to your tire size

from the wheel size chart.

4.1 Technical data

4.1.1 Battery indicator / replacement

Please see the enclosed diagrams for how to insert or

remove the battery. After changing the battery in the

computer head unit, only the time needs to be re-set.

BC 14.12 ALTI Type CR 2032 /

computer head unit: 1.5-year service life*

BC 14.12 STS ALTI Type CR 2032 /

computer head unit: 1-year service life*

Speed transmitter: Type CR 2032 /

1-year service life*

* when used for one hour per day

4. Important Notes / Troubleshooting

4.1.2 Troubleshooting

No speed:

– Is the computer correctly fastened into the bracket?

– Check the distance between the magnet and the

sensor (max. 12 mm).

– Is the magnet correctly positioned?

Incorrect speed:

– Are two magnets attached to the bike?

– Is the wheel size correctly set?

Further troubleshooting solutions can be found in our

FAQs at www.sigmasport.com

Andere Handbücher für BC 14.12 ALTI

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sigma Fahrradzubehör Handbücher

Sigma

Sigma 500 Bedienungsanleitung

Sigma

Sigma ROX 11.1 EVO Anleitung zur Verwendung

Sigma

Sigma Sport BC 500 Bedienungsanleitung

Sigma

Sigma ROX 8.0 Bedienungsanleitung

Sigma

Sigma 1200 Bedienungsanleitung

Sigma

Sigma NUGGET II Bedienungsanleitung

Sigma

Sigma BC1200 Bedienungsanleitung

Sigma

Sigma ROX 12.1 EVO Bedienungsanleitung

Sigma

Sigma CURVE Bedienungsanleitung

Sigma

Sigma ROX 11.1 EVO Anleitung zur Verwendung

Sigma

Sigma 1200 Bedienungsanleitung

Sigma

Sigma BC 1609 Bedienungsanleitung

Sigma

Sigma ROX 2.0 Bedienungsanleitung

Sigma

Sigma BC 14.16 Bedienungsanleitung

Sigma

Sigma BC 12.12 Bedienungsanleitung

Sigma

Sigma BC 1106 DTS Bedienungsanleitung

Sigma

Sigma AURA 30 Bedienungsanleitung

Sigma

Sigma BC 906 Bedienungsanleitung

Sigma

Sigma ROX 12.0 SPORT Bedienungsanleitung

Sigma

Sigma ROX 2.0 Anleitung zur Verwendung

Sigma

Sigma BC 1606L DTS cadence Bedienungsanleitung

Sigma

Sigma BC 2209 MHR Bedienungsanleitung

Sigma

Sigma ROX 10.0 GPS Bedienungsanleitung

Sigma

Sigma BUSTER 200 Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken

Playcore

Playcore Dero Setbacks Bedienungsanleitung

VDO Cyclecomputing

VDO Cyclecomputing x3dw Bedienungsanleitung

Cateye

Cateye RAPID X2 Bedienungsanleitung

buratti meccanica

buratti meccanica Clorofilla Trail Bedienungsanleitung

Shimano

Shimano SG-8R20 Betriebsanleitung

BOB

BOB YAK Bedienungsanleitung

APLIC

APLIC 303303/20190717TW012 Bedienungsanleitung

SRAM

SRAM AXS BlipBox Bedienungsanleitung

Garmin

Garmin EDGE 500 Bedienungsanleitung

Shimano

Shimano FD-RX810 Bedienungsanleitung

Cateye

Cateye V2C - Gebrauchsanweisung

KMART

KMART 43115907 Bedienungsanleitung

SIGMA SPORT

SIGMA SPORT Buster 2000 Bedienungsanleitung

NVO Components

NVO Components STEM Bedienungsanleitung

DAXYS

DAXYS BP188 Bedienungsanleitung

XLC

XLC BV-W17 Bedienungsanleitung

Deda Elementi

Deda Elementi SUPERBOX Bedienungsanleitung

Key-Disp

Key-Disp KD31M Bedienungsanleitung