SIIG CyberSerial POS 4000RJ Bedienungsanleitung

CyberSerial POS 4000RJ

Quick Installation Guide

04-0230A

Introducing the

CyberSerial POS

4000RJ

TheCyberSerial POS 4000RJ isahigh-speedplug-n-playPCIbusserial

I/O card that provides 5V or 12V DC output.

Features and Benefits

•Provides four RJ45 high-speed serial ports which can be

individually configured as standard RS232 serial ports or RS232

serial ports with 5V/12V DC output

• Supports both 8-pin and 10-pin RJ45 cable for device connections

•Conforms to PCI v2.2 Plug and Play

•Full support for DOS and Windows based software

•Improves I/O access speed up to 8 times faster than existing

ISA-bus serial ports. Reduces CPU load and improves system

performance dramatically

•IRQ sharing feature eliminates IRQ conflicts

•Works with 56K V.90 external modems, ISDN terminal adapters,

PDAs, digital cameras, label printers and other serial port devices

•Built-in 16-byte (32-byte for 16650 model, 128-byte for 16850

model) FIFO buffers dramatically increase data transmit/receive

speed, especially under Windows multitasking environment

System Requirements

•Pentium or equivalent computer with an available 32-bit PCI slot

•DOS/Windows 3.1x, Windows 95/98/98 SE/ME/NT 4.0/2000/

Package Contents

• One CyberSerial POS 4000RJ board

• One driver installation diskette

• One 5-year warranty card

• This quick installation guide

Hardware Installation

General instructions for installing the card are provided below,

since the design of computer cases and motherboards vary. Refer

to your computer’s reference manual for further information, if

needed.

Caution: Static Electricity Discharge may permanently damage

your system. To avoid possible static electricity discharge during

the installation, please follow the guidelines below:

•Dischargeanystaticelectricitybuildupinyourbodyby

touchingalargegroundedmetalsurfaceorthecomputer’scase

(ifpluggedin), forafewseconds.

•During the installation, avoid any contact with internal parts.

Handle cards only by their external edges.

1. Turn OFF the power to your computer and any other

connected peripheral devices.

2. Unplug the power cord from the back of the computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card's bus connector

with the selected PCI slot on the motherboard. Push the board

down firmly, but gently, until it is well seated.

6. Replace the slot bracket's holding screw to secure the card.

7. Replace the computer cover and reconnect the power cord.

Pin Definition, Jumper Settings and Layout

RJ45 10-Pin Pin Definition

Pin#12345678910

Signal RI or

5/12V

DC DSR RTS CD or

5/12V

DC TX RX Signal

GND CTS DTR Case

GND

RJ45 8-Pin Pin Definition

Standard RS-232 DB9 Pin Definition

RI Pin Jumper Settings

Key: O=Open, S=Short, -=N/A

Pin#12345678

nal DSR RTS CD or

5/12V

DC TX RX Si

nal

GND CTS DTR

Pin#123456789

nal CD RX TX DTR GND DSR RTS CTS RI

Port Mode JP1 JP2 JP3 JP4 JP9

Port1RIO----

Port 2 RI - O - - -

Port 3 RI - - O - -

Port4RI---O-

Port 1 5V S - - - 1-2 S

Port 2 5V - S - - 1-2 S

Port 3 5V - - S - 1-2 S

Port45V---S1-2S

Port 1 12V S - - - 2-3 S

Port 2 12V - S - - 2-3 S

Port 3 12V - - S - 2-3 S

Port412V---S2-3S

CD Pin Jumper Settings

Key: O=Open, S=Short, -=N/A

Port Mode JP5 JP6 JP7 JP8 JP10

Port1CDO----

Port2CD-O---

Port 3 CD - - O - -

Port4CD---O-

Port 1 5V S - - - 1-2 S

Port 2 5V - S - - 1-2 S

Port 3 5V - - S - 1-2 S

Port 4 5V - - - S 1-2 S

Port 1 12V S - - - 2-3 S

Port 2 12V - S - - 2-3 S

Port 3 12V - - S - 2-3 S

Port 4 12V - - - S 2-3 S

Board Layout

JP8

JP4

JP3

JP6

JP2

JP5

JP1

JP7

JP9

JP10

CyberSerial Pos 4000RJ board layout

Jumper Description

•JP1: Select RI/voltage output for Port 1

• JP2: Select RI/voltage output for Port 2

• JP3: Select RI/voltage output for Port 3

•JP4: Select RI/voltage output for Port 4

•JP5: Select CD/voltage output for Port 1

•JP6: Select CD/voltage output for Port 2

•JP7: Select CD/voltage output for Port 3

•JP8: Select CD/voltage output for Port 4

•JP9: Select RI Pin voltage output for port 1, 2, 3 and 4

• JP10: Select CD Pin voltage output for port 1, 2, 3 and 4

Port 4

Port 3

Port 1

Port 2

Software Installation

This section provides information on how to install the

CyberSerial POS 4000 drivers for the following operating systems:

Windows 95b/98/98 SE/ME

Windows NT 4.0

Windows 2000

Windows XP

DOS/Windows 3.1x

Windows 95b Driver Installation

1. At the Update Device Driver Wizard window, click Next.

2. Insert the Driver Installation diskette in the floppy drive, and

click Other Locations. Type in a:\Win95, click OK, then

Finish.

3. From the Insert Disk window, click OK. When the Copying

Files dialog box appears, type in a:\Win95, then click OK.

4. Remove the diskette and select Yes to restart the computer for

the setup to take effect.

Windows 98/98 SE Driver Installation

1. At the Add New Hardware Wizard window, click Next.

2. Select Search for the best driver for your device

(Recommend), then click Next.

3. Select Specify a location, insert the Driver Installation diskette

and type in a:\Win98, then click Next.

4. Click Next, then Finish.

5. Remove the diskette and click Yes to restart your system.

Windows ME Driver Installation

1. At the Add New Hardware Wizard screen, choose Specify the

location of the driver (Advanced), then click Next.

2. Check Specify a location, insert the Driver Installation diskette

into your floppy drive, type in A:\Win98, then click Next.

3. Click Next, and Finish to complete driver installation.

4. Remove the driver diskette and click Yes to restart Windows.

To verify successful installation in Windows 95/98/98 SE/ME:

1. From the main desktop, double click My Computer, Control

Panel,System,then click Device Manager.

2. Double click Ports (COM & LPT) and new Cyber PCI ports

should be displayed. Also, double click SIIG Cyber PCI

option and SIIG ... PCI Board should be displayed.

The board is ready to connect new devices.

Windows NT 4.0 Driver Installation

1. From the desktop click Start, then Run.

2. Insert the Driver Installation diskette, type in A:\NT4\setup,

then click OK.

3. Click Next when the Welcome window appears.

4. From Choose Destination Location window, click Next.

5. Remove the Driver Installation diskette, select Yes to restart

Windows and click Finish.

To verify successful installation in Windows NT 4.0:

1. Go to Start / Setting / Control Panel,double click SIIG Cyber

PCI 20X device icon.

2. New COM port address and LPT number will be assigned for

the ports when successfully installed. The board is ready to

connect devices.

To change the I/O address in Windows NT 4.0:

1. Double click Start, Settings, Control Panel,then SIIG Cyber

PCI 20X device icon.

2. Highlight the LPT or COM address and click Settings.

3. Select or type in an I/O address supported by the device you

would like to configure and click OK. Make sure the selected

I/O address does not conflict with other device in your system.

4. Select Restart Now for the new setup to take effect.

Windows 2000 Driver Installation

1. At the New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(recommended) and click Next.

3. Select Specify a location, uncheck the other options and click

Next.

4. Insert the Driver Installation diskette, type in A:\Win2K and

click OK.

5. Click Next and Finish to complete driver installation.

Windows XP Driver Installation

1. At the Found New Hardware Wizard select Install from a list

or specific location (Advanced), then click Next.

2. Insert the Driver Installation diskette, check Include this

location in the search, type in A:\Win2K and click Next.

3. Click Continue Anyway and Finish.

4. Repeat steps 1-3 four more times.

5. Restart the computer to complete the installation.

To verify successful installation in Windows 2000/XP:

1. Double click My Computer, Control Panel, System, Hardware,

and click Device Manager.

2. Click on the + (plus sign) in front of Ports (Com & LPT).

3. New Cyber port(s) should be listed.

DOS/Windows 3.1x Driver Installation

1. Insert the Driver Installation diskette, from the C: prompt, type

in copy a:\dos\*.*,then press <Enter>.

2. Type in edit autoexec.bat, then press <Enter>.

3. Add C:\CB20XPC.exe at the bottom of the autoexec.bat file.

4. Go to File, save the changes and exit.

5. Remove the diskette and restart the system for the new setup to

take effect.

Technical Support

QUESTIONS? SIIG’s Online Support has the answers! Simply

visitour web site at

www.siig.com

and click onSupport/Drivers.

Our online support database is updated daily with new drivers

and solutions. The answers to your problems could be just a few

clicks away.

Return Merchandise Authorization (RMA)

SIIGwarrantstotheoriginalbuyeroftheproductthatthehardware

isfree ofdefectsinmaterialsandworkmanshipforaperiod ofone,

twoorfiveyearsfromthedate of purchase. If your productfailsto

be in good working order during the warranty period, you may

return it to SIIG for repair or replacement at SIIG's option.

To return the product, you need to follow these steps.

Step 1: Contact SIIG's RMA Department

ToobtainanRMAnumber,SIIG'sRMADepartmentcanbereached

by phone at (510)413-5333 or fax at (510)657-5962 or email at

[email protected]. In order to issue an RMA number, the product

serialnumber isrequired. Thisnumbercanbe foundonthesideof

the box and on the back of the product.

Step 2: Complete the RMA form

• FilloutyourReturnMerchandiseAuthorization(RMA)form,and

include it in the package with the product.

• Properlypacktheproductforshipping. Allsoftware,cable(s)and

other accessories that came with the original package must be

included.

• ClearlywriteyourRMAnumberonthetopofthereturnedpackage

and on the accompanying RMA form.

SIIGwillrefusetoacceptanyshippingpackage,and will not

beresponsibleforaproductreturnedwithoutanRMAnumber

posted on the outside of the shipping carton.

Step 3: Ship the Product

You are responsible for the cost of shipping back to SIIG at the

following address:

SIIG, Inc. RMA#_______________

6078 Stewart Ave.

Fremont, CA 94538

SIIGwillshiptherepairedor replaced product via UPSGroundor

US Mail at no cost to you.

PRODUCTNAME MODEL NUMBER

CyberSerial POS 4000RJ IO1018

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a

ClassB digitaldevice,pursuant topart15 ofthe FCCRules.These limitsare

designed to provide reasonable protection against harmful interference in a

residentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio

frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticular

installation. If this equipment does cause harmful interference to radio and

television reception, which can be determined by turning the equipment off

andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormore

of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio or TV technician for help

Caution:

Any changes or modifications not expressly approved by the party

responsibleforcompliancecouldvoid theuser'sauthoritytooperate

this equipment

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

CyberSerial POS 4000RJ is a trademark of SIIG, Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows

NT are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of

Intel Corporation. Other names used in publication are for identification only and may be

trademarks of their respective companies.

Inhaltsverzeichnis

Andere SIIG Computerhardware Handbücher

SIIG

SIIG NN-403P12 Bedienungsanleitung

SIIG

SIIG ID-P40411-S1 Bedienungsanleitung

SIIG

SIIG Network Device EVTEK-5103 Installationsanleitung

SIIG

SIIG FireWire 800 2-Port ExpressCard/34 Bedienungsanleitung

SIIG

SIIG NN-PCMM12-S3 Bedienungsanleitung

SIIG

SIIG Silent Mini Notebook Cooler Bedienungsanleitung

SIIG

SIIG CE-ED0011-S1 Bedienungsanleitung

SIIG

SIIG SC-SAE512-S1 Bedienungsanleitung

SIIG

SIIG NN-PC8312-S2 Bedienungsanleitung

SIIG

SIIG Serial ATA PCI Bedienungsanleitung

SIIG

SIIG Low Profile USB Adapter Bedienungsanleitung

SIIG

SIIG DP PCI-to-PS/2 Bedienungsanleitung

SIIG

SIIG JJ-E02111-S1 Bedienungsanleitung

SIIG

SIIG Serial ATA PCI RAID Bedienungsanleitung

SIIG

SIIG Single-Serial PC Card Bedienungsanleitung

SIIG

SIIG USB 2.0 9-in-1 Bay R/W Bedienungsanleitung

SIIG

SIIG eSATA II ExpressCard Bedienungsanleitung

SIIG

SIIG UltraATA 133 PCI Bedienungsanleitung

SIIG

SIIG SoundWave 5.1 PCI Bedienungsanleitung

SIIG

SIIG DP PCI-to-PS/2 Bedienungsanleitung

SIIG

SIIG SoundWave 5.1 PCI-LP Bedienungsanleitung

SIIG

SIIG DP FireWire 800 3-Port PCIe Bedienungsanleitung

SIIG

SIIG SC-SB6412 Bedienungsanleitung

SIIG

SIIG USB 2.0+1394 DV Kit Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung