SKF LINKOLN A Series Bedienungsanleitung
Installation guide
Model 84824, series “A”
Overfill warning device
Date of issue December 2016
Form number 403496
Version 2
Read manual prior to installation or use of
this product. Keep manual nearby for future
reference.
Contents
Description. . . . . . . . . . . . . . . . . . . . . . . 3
Owner/Operator responsibility . . . . . . 3
Installation. . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . 4
Exploded views . . . . . . . . . . . . . . . . . . . 5
Warranty . . . . . . . . . . . . . . . . . . . . . . . . 8
2
Description
Model 84824 overfill warning device,
designed for double wall tanks, functions as
air supply shut-off to pump when tanks
reach near full capacity. In shut-off position,
air is diverted from pump to signal whistle to
alert full tank condition. Warning device
automatically resets when tank is emptied.
Periodical operational testing can be
performed by lifting test button about one
inch; this should shut-off air to pump and
sound signal whistle. Release button and
valve will reset itself.
Owner/Operator
responsibility
It is responsibility of owner/operator to
properly use and maintain equipment.
It is responsibility of owner/operator to
maintain legibility of all warning and
instruction labels.
Owner/Operator shall retain manual for
future reference to important warnings,
operating and maintenance instructions.
Table 1
Specifications
Fits into 2 in.NPT tank opening
Air inlet port 1/4in. NPT internal
Air outlet port 1/4in. NPT internal
Overall height 29 5/8 in. (752,5 mm)
Maximum air pressure 100 psi (6,89 mm)1)*
1) Use of an air filter, regulator and lubricator is recommended to prevent damage to unit.
* Indicates change.
WARNING
This device is not intended to reduce or
replace user responsibility when transferring
liquids to holding tank.
Failure to comply may result in death or
serious injury.
3
Installation
1 Valve must be installed in direction that
will permit free rise and fall of float
assembly. Inspect tank interior for baffles
that can obstruct float action.
2 Back off set screw in threaded collar one
full turn; this will release collar and allow it
to rotate freely around valve body.
3 Insert valve assembly into bung opening at
top of tank. Arrow on top of valve must
point to tank area selected for float
operation.
4 Hold valve top in position while screwing
valve collar into tank. Collar is fitted to
accommodate spanner wrench for
tightening.
5 Recheck arrow to make sure valve is in
desired operating position before
tightening collar set screw. When set
screw is tightened, valve is lockedin
operating position.
6 Place filters, regulators, oilers and air
valves in front of air supply line going to in
port of valve. Never place accessories and
valves in air supply line from out port to
pump.
Maintenance
Overfill warning device is similar to fine air
tool in that effective life and performance
can be reduced by dirty air (air that has not
been filtered to remove moisture and rust
particles).
Installation of filter, regulator and oiler in
air supply line going to in port is
recommended to minimize failures in valve
and pump. Hydraulic oil or 10 WT motor oil
is recommended for use in lubricator.
Antifreeze can be substituted for oil
whenever combination of extreme cold and
wet air are present.
Overfill warning device should be tested
several times per year. Test can be
accomplished by lifting test button one inch;
this will cut off air to pump and sound signal
whistle. Release button and valve will reset.
4
Float direction
indicator arrow
Tape
measure
Collar
Test port
Signal/whistle
port
Test port cap
Signal whistle
Collar set
screw
Valve body
Float and rod
O-ring
Concrete
Valve body
A
8 in.
(203,2 mm)
Ø 2 in. pipe
(50,8 mm)
View A View B
/ in. NPT
Air in port
14
29 / in.
(752,5 mm)*
58
Out port
1)
Fig. 1
NOTE
Signal whistle may have to be removed
when installing plumbing. Reassemble
whistle to unit when plumbing is
complete.
NOTE
No warranty or guarantee of
merchantability, or fitness for particular
purpose, or any other kind, expressed or
implied, for function of or service
performed by overfill warning device.
NOTE
Collar is moved in direction of o-ring in
fixed position.
NOTE
For collar height and o-ring settings on
valve body, measure inside of pipe for
proper length (dimension A, view A).
This will then be distance between
inside of collar and o-ring
(example: 8 in. (203,2 mm)- View B).
1) Unit will shut off air supply to pump at 60 to 65° point of extension.
* Indicates change.
5
This page left intentionally blank.
6
This page left intentionally blank.
7
Warranty
The instructions do not contain any informa-
tion on the warranty. This can be found in
the General Conditions of Sales, available at:
www.lincolnindustrial.com/technicalservice
or www.skf.com/lubrication.
®SKF is a registered trademark of the SKF Group.
®Lincoln is a registered trademark of Lincoln Industrial Corp.
©SKF Group 2016
The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permis-
sion is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be
accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
PUB LS/I4 16987 EN · December 2016 · Form 403496 Version 2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere SKF Schmiersystem Handbücher
SKF
SKF 501-301-310-S1 Bedienungsanleitung
SKF
SKF Vectolub VTEC Leitfaden
SKF
SKF Lincoln COBRA 1X-R2 Bedienungsanleitung
SKF
SKF LINCOLN EDL1 Bedienungsanleitung
SKF
SKF GVP-S-049-1 Bedienungsanleitung
SKF
SKF TLG Bedienungsanleitung
SKF
SKF LINCOLN P203 Bedienungsanleitung
SKF
SKF SKF SYSTEM 24 Bedienungsanleitung
SKF
SKF HS04 Bedienungsanleitung
SKF
SKF LINCOLN ATEX PSG1 Series Bedienungsanleitung
SKF
SKF VectoLub VE1B Leitfaden
SKF
SKF KGF Series Konfigurationshandbuch
SKF
SKF TLMP 1008 Series Bedienungsanleitung
SKF
SKF ST-1240-GRAPH Bedienungsanleitung
SKF
SKF GVP-S-034-3D+924 Bedienungsanleitung
SKF
SKF CLU5 Bedienungsanleitung
SKF
SKF TLAC 50/B Bedienungsanleitung
SKF
SKF VSG Series Bedienungsanleitung
SKF
SKF CLU4eco PDYE Series Kurzanleitung
SKF
SKF TLMR 101 Bedienungsanleitung
