SKF SKF SYSTEM 24 Bedienungsanleitung

Instructions for use

TLSD 1-DK

SKF SYSTEM 24

3EN

Safety recommendations......................................................................4

EU Declaration of Conformity ...............................................................5

UK Declaration of Conformity ...............................................................6

1. Technical data................................................................................7

2. Installation ....................................................................................8

2.1 Installation of new lubricators ..............................................................9

2.2 Replacement of canisters ....................................................................11

3. Troubleshooting...........................................................................21

Table of contents

Original instructions

4EN

Safety recommendations

MP5514

www.skf.com/lubrication

MSDS

+15°C

(59ºF)

+25°C

(77ºF)

Max

3 Years

LGFP 2

LHMT 68

LHFP 150

LHHT 265

Max

2 Years

5EN

EU Declaration of Conformity

TLSD 1-DK

Automatic single point lubricator Cabled TLSD

We, SKF MPT, Meidoornkade 14, 3992 AE Houten, The Netherlands

herewith declare under our sole responsibility that the products described

in these instructions for use, are in accordance with the conditions of the

following Directive(s):

EMC DIRECTIVE 2014/30/EU

RoHS DIRECTIVE (EU) 2015/863

and are in conformity with the following harmonized standards:

EN 61000-6-3:2007/A1:2011/AC:2012:

Electromagnetic compatibility (EMC). Generic standards.

Emission standard for residential, commercial and light-industrial

environments.

EN 61000-6-2:2005/AC:2005:

Electromagnetic compatibility (EMC). Generic standard.

Immunity for industrial environments.

EN 61000-4-2: ESD

EN 61000-4-3: HF Immunity

EN 61000-4-4: EFT

EN 61000-4-5: Surge

EN 61000-4-6: CDN/Clamp Injection

EN 61000-4-8: Power Magnetic ﬁeld

EN IEC 63000:2018

Technical documentation for the assessment of electrical and electronic

products with respect to the restrictions of hazardous substances.

Houten, The Netherlands, October 2021

Mrs. Andrea Gondová

Manager Quality and Compliance

6EN

UK Declaration of Conformity

TLSD 1-DK

Automatic single point lubricator Cabled TLSD

We, SKF MPT, Meidoornkade 14, 3992 AE Houten, The Netherlands

herewith declare under our sole responsibility that the products described

in these instructions for use, are in accordance with the conditions of the

following Directive(s):

Electromagnetic Compatibility Regulations 2016 (2016 No. 1091)

The Restriction of the Use of Certain Hazardous Substances in Electrical and

Electronic Equipment Regulations 2012 (2012 No. 3032)

and are in conformity with the following harmonized standards:

EN 61000-6-3:2007/A1:2011/AC:2012:

Electromagnetic compatibility (EMC). Generic standards.

Emission standard for residential, commercial and light-industrial

environments.

EN 61000-6-2:2005/AC:2005:

Electromagnetic compatibility (EMC). Generic standard.

Immunity for industrial environments.

EN 61000-4-2: ESD

EN 61000-4-3: HF Immunity

EN 61000-4-4: EFT

EN 61000-4-5: Surge

EN 61000-4-6: CDN/Clamp Injection

EN 61000-4-8: Power Magnetic ﬁeld

EN IEC 63000:2018

Technical documentation for the assessment of electrical and electronic

products with respect to the restrictions of hazardous substances.

The person authorised to compile the technical documentation on

behalf of the manufacturer is SKF (U.K.) Limited, 2 Canada Close,

Banbury, Oxfordshire, OX16 2RT, GBR.

Houten, The Netherlands, October 2021

Mrs. Andrea Gondová

Manager Quality and Compliance

7EN

1. Technical data

Designation TLSD 1-DK

Automatic single point lubricator Cabled TLSD

Maximum ratings

Voltage supply (VSS-GND) 7 V to 35 V

Current supply up to 1.5 A

Quiescent current

(sleep current)

<10 mA

Relay maximum voltage 35 V

Relay minimum current 100 mA

Ambient temperature range -20 to 50 °C (-4 to 122 °F)

Max. working pressure 5 Bar

Cable

Length 550 mm

Diameter 4.8 mm Max.

Wire size 24 AWG 7/32 (0.25 mm2)

Fig. 1 – WHITE -> +Positive (VCC)

BROWN -> -Negative (GND)

GREEN -> Relay contact 1 (NO)

YELLOW -> Relay contact 2 (NO)

WARNING:

Should the power loss the dispense rate quantity calculation should be

adjusted.

8EN

2. Installation

This user manual provides technical information about:

SKF SYSTEM 24 - Cabled TLSD Series

TLSD 1-DK

Related documentation:

Document: On-line training Lubrication

Publication

Click here

Selection tools for:

Document: - LubeSelect for SKF greases

Publication

Click here

Document: - Lubricators settings Dial Set

Publication

Click here

Document: On-line DialSet

Publication

Click here

Document:

SKF SYSTEM 24 – Cabled series TLSD 1-DK

Publication MP5514

9EN

2.1 Installation of new lubricators

For installation at the application follow the steps:

Clean the lubrication point from dirt and

old grease in such a way that the dirt is not

entering the lubrication point itself.

Remove the yellow protection cap from the

new grease cannister.

Screw the support ﬂange on the cartridge

until is it is ﬁxed.

If the support ﬂange is mounted already on

the application, don’t remove it. Use sealing

tape on the thread of the new cannister tip.

10 EN

Place the drive unit on top of the full grease

cannister and make sure the teeth of both

parts are engaged.

The spindle head should now be inside of the

motor coupler.

Screw the drive unit cap onto the cannister.

If the support ﬂange is not mounted on the

application, screw the complete lubricator

onto the application. Your lubricator is ready.

If the support ﬂange is mounted already

on the application, the use of sealing tape

(PTFE) on the thread of the new cannister tip

is recommended.

Then screw the cartridge on the support

ﬂange mounted in the application.

Your lubricator is ready.

Andere Handbücher für SKF SYSTEM 24

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SKF Schmiersystem Handbücher

SKF

SKF KGF Series Konfigurationshandbuch

SKF

SKF LINCOLN FF Series Bedienungsanleitung

SKF

SKF LINCOLN ATEX PSG1 Series Bedienungsanleitung

SKF

SKF LINCOLN EDL1 Bedienungsanleitung

SKF

SKF Lincoln COBRA 1X-R2 Bedienungsanleitung

SKF

SKF HTL201 EEX Bedienungsanleitung

SKF

SKF TLGU 10 Bedienungsanleitung

SKF

SKF UFD20 Series Bedienungsanleitung

SKF

SKF OLA 1 Series Bedienungsanleitung

SKF

SKF LAGD 60/U Bedienungsanleitung

SKF

SKF 729101/300MP Bedienungsanleitung

SKF

SKF VSG Series Bedienungsanleitung

SKF

SKF TLMP 1008 Series Bedienungsanleitung

SKF

SKF TLMR Bedienungsanleitung

SKF

SKF LUBRILEAN Basic Bedienungsanleitung

SKF

SKF LAGD 400 Bedienungsanleitung

SKF

SKF CLU5 Bedienungsanleitung

SKF

SKF KFG Bedienungsanleitung

SKF

SKF TLMR 101 Bedienungsanleitung

SKF

SKF CLU4eco PDYE Series Kurzanleitung

SKF

SKF VectoLub VE1B Leitfaden

SKF

SKF 501-301-310-S1 Bedienungsanleitung

SKF

SKF LINCOLN ZPU 01 Version E Bedienungsanleitung

SKF

SKF LUBRILEAN Vario Bedienungsanleitung

Beliebte Schmiersystem Handbücher anderer Marken

Atlanta

Atlanta BKI 109 e Bedienungsanleitung

Viper

Viper Maxi MK 2 Beilage

MEMOLUB

MEMOLUB HPS Bedienungsanleitung

BEROTEC

BEROTEC Mofessor Bedienungsanleitung

TUTORO

TUTORO Auto Gebrauchsanweisung

Bijur Delimon

Bijur Delimon V5B Bedienungsanleitung

iSHAN

iSHAN YGL-L Bedienungsanleitung

iSHAN

iSHAN YET-A1 Bedienungsanleitung

DLS

DLS FlexxPump 1500 Bedienungsanleitung

Lincoln

Lincoln SKF KFU2 Series Bedienungsanleitung

Sumake

Sumake SA-2362M Bedienungsanleitung

Graco

Graco 203-697 E Series Bedienungsanleitung

SMC Networks

SMC Networks AL Series Bedienungsanleitung

MEMOLUB

MEMOLUB HPS Bedienungsanleitung

Wittenstein Alpha

Wittenstein Alpha LUC+400 Bedienungsanleitung

Burks

Burks 104300 Bedienungsanleitung

DLS

DLS 125 Bedienungsanleitung

Emerson

Emerson NL4-LBM Series Montageanleitung