SMART Board Board 600i5 Bedienungsanleitung

SMART Board™ 600i5

Interactive Whiteboard

System

Conﬁguration and User’s Guide

PLEASE THINK BEFORE YOU PRINT

Trademark Notice

SMART Board, SMART Notebook, smarttech, the SMART logo and all SMART taglines are trademarks or registered

trademarks of SMART Technologies ULC in the U.S. and/or other countries. Texas Instruments, Brilliant Color, DLP and DLP

Link are Trademarks of Texas Instruments. HDMI is a trademark or registered trademark of HDMI Licensing LLC. Phillips is a

registered trademark of Phillips Screw Company. Microsoft, Windows and Internet Explorer are either registered trademarks or

trademarks of Microsoft Corporation in the U.S. and/or other countries. Blu-ray is a trademark of the Blu-ray Disc Association.

Patents

US5448263; US6141000; US6320597; US6326954; US6337681; US6540366; US6741267; US6747636; US7151533;

US7289113; US7499033; US7626577; US7687736; US7757001; CA2058219; and CA2252302. Other patents pending.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

stored in a retrieval system or translated into any language in any form by any means without the prior written consent of

SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment

on the part of SMART.

12/2010

Important information

Before you install and use your SMART Board™ 600i5 or D600i5 interactive whiteboard system, read

and understand the safety warnings and precautions in this user’s guide and the included warnings

document. These safety warnings and precautions describe the safe and correct operation of your

interactive whiteboard system and its accessories, helping you to prevent injuries and equipment

damage. Ensure that your interactive whiteboard system is always being used correctly.

In this document, “SMART Board 600i5 or D600i5 interactive whiteboard system” refers to your

SMART Board 600 or D600 series interactive whiteboard and its SMART UF75 or UF75w projector,

accessories and optional equipment.

The SMART UF75 or UF75w projector included with your system is designed to work only with

certain SMART Board interactive whiteboard models. Contact your authorized SMART reseller

(smarttech.com/wheretobuy) for more information.

Safety warnings, cautions and important

information

W W A R N I N G

lFailure to follow the installation instructions shipped with your SMART product could result in

personal injury and damage to the product.

lTo reduce the risk of fire or electric shock, do not expose the SMART product to rain or

moisture.

lTwo people are required to mount your SMART product because it may be too heavy for one

person to safely maneuver.

When you lift your interactive whiteboard, you and your assistant should stand on either side

of the screen, supporting its weight at the bottom while balancing the top with your other

hands.

lWhen mounting the projector boom on a framed or hollow wall, attach both the mounting

bracket and the safety tether to a stud to safely support the projector’s weight. If you use only

drywall anchors, the drywall can fail, resulting in product damage and possible personal

injury.

lDo not leave cables on the floor where they can be a tripping hazard. If you must run a cable

over the floor, lay it in a flat, straight line and secure it to the floor with tape or a cable

management strip of a contrasting color. Handle cables carefully and avoid excessive

bending.

lIf you are using an RS-232 serial expansion module, a wireless Bluetooth® connection

expansion module or a USB audio system, use only the power supply included with that

product. These products do not use the same power supplies. Using the wrong power supply

might create a safety hazard or damage the equipment. If in doubt, refer to the specification

sheet for your product to verify the power supply type.

lDo not climb (or allow children to climb) on a wall- or stand-mounted SMART Board

interactive whiteboard.

Do not climb on, hang from or suspend objects from the projector boom.

Climbing on the interactive whiteboard or projector boom could result in personal

injury or product damage.

lThere are no user-serviceable parts inside the pen tray. Only qualified personnel should

disassemble the pen tray’s printed circuit boards, and this procedure must be done with

proper electrostatic discharge (ESD) protection.

lViewing 3D content from a projector may cause epileptic seizures or strokes. If you or any

member of your family has a history of light-sensitive seizures, consult a doctor before

viewing 3D content.

lViewing 3D content while you are consuming alcohol, experiencing sleep deprivation or in

poor physical condition may be unsafe.

lPregnant women and elderly individuals should avoid viewing 3D content.

lViewing 3D content may cause sickness, including nausea, dizziness, headache, eyestrain,

blurred vision or numbness. If you experience any of these symptoms, stop viewing 3D

content immediately. If these symptoms persist, consult a doctor.

lParents and teachers should monitor children and students for adverse effects resulting from

viewing 3D content since children and teenagers may be more susceptible than adults to

related health risks.

I M P O R T A N T I N F O R M A T I O N

lTo avoid adverse effects resulting from viewing 3D content with your interactive whiteboard

system, observe the following precautions:

oDo not use 3D glasses for viewing any material other than 3D content.

oMaintain a minimum distance of 7' (2 m) from your interactive whiteboard system's

screen. Viewing 3D content from too close a distance may result in eyestrain.

oAvoid viewing 3D content for a prolonged period of time. Take a break of 15 minutes or

longer after every hour of viewing.

oFace the screen squarely when viewing 3D content. Viewing 3D content from an angle

may cause fatigue or eyestrain.

C C A U T I ON

lDo not operate this unit immediately after moving it from a cold location to a warm location.

When the unit is exposed to such a change in temperature, moisture can condense on the

lens and crucial internal parts. Allow the system to stabilize to room temperature before

operation to prevent possible damage to the unit.

lDo not place the unit in hot locations, such as near heating equipment. Doing so could cause

a malfunction and shorten the life of the projector.

lAvoid setting up and using the SMART product in an area with excessive levels of dust,

humidity and smoke.

lDo not place your SMART product in direct sunlight or near any appliance that generates a

strong magnetic field.

lIf you need to lean the interactive whiteboard against a wall before you mount it, make sure it

remains in an upright position, resting on the pen tray brackets, which can sustain the weight

of the interactive whiteboard.

Do not rest the interactive whiteboard on its side or on the top of the frame.

lYou must connect the USB cable that came with your SMART Board interactive whiteboard

to a computer that has a USB compliant interface and that bears the USB logo. In addition,

the USB source computer must be compliant with CSA/UL/EN 60950 and bear the CE mark

and CSA and/or UL Mark(s) for CSA/UL 60950. This is for operating safety and to avoid

damage to the SMART Board interactive whiteboard.

I M P O R T A N T I N F O R M A T I O N

iii

lDo not block the projector’s ventilation slots and openings.

lAvoid putting the projector into Standby mode during the lamp ignition phase because this

can lead to premature lamp failure. Keep the projector lamp on for a minimum of 15 minutes

before putting it into Standby mode to preserve the lamp life.

lIn a high altitude location over 6000' (1800 m), where the air is thin and cooling efficiency is

reduced, use the projector with the fan mode set to High.

lCycling power to the projector repeatedly can lock or damage your SMART product. After

you put the product into Standby mode, wait at least 15 minutes for cooling before starting

the product again.

lDo not adjust any settings in the service menu other than those listed in the following

procedures. Changing other settings might damage or affect the operation of your projector

and invalidates your warranty.

lIf dust or small items prevent pen tray buttons from being pressed or cause constant button

contact, remove the obstructions carefully.

lBefore you clean the SMART UF75 or UF75w projector, press the Power button twice on

the ECP or remote control to put the system into Standby mode, and then allow the lamp to

cool for 30 minutes.

lDo not spray cleaners, solvents or compressed air near any part of the projector because

they can damage or stain the unit. Spraying the system could spread a chemical mist on

some of the projector’s components and lamp, resulting in damage and poor image quality.

lDo not allow liquids or commercial solvents of any kind to flow into the projector.

lWhen transporting your SMART product, repack it with as much of the original packaging as

possible. This packaging was designed with optimal shock and vibration protection.

lIf your SMART product requires replacement parts, make sure the service technician uses

replacement parts specified by SMART Technologies or parts with the same characteristics

as the original.

I I M P O R T A N T

lUse the instructions included with the ECP to install your interactive whiteboard, projector

and ECP. The instructions in your SMART Board interactive whiteboard box do not include

instructions for installing the SMART UF75 or UF75w projector or ECP.

lMake sure an electrical socket is near your SMART product and remains easily accessible

during use.

I M P O R T A N T I N F O R M A T I O N

lUsing your SMART product near a TV or radio could cause interference to the images or

sound. If this happens, move the TV or radio away from the projector.

lIf you have peripheral devices that do not use a 4-pin mini-DIN connector or an RCA

composite video jack, or if your device has an audio connection that does not use RCA

jacks, you may need to purchase third-party adapters.

lThere are no projector menu options on the ECP. Keep your remote control in a safe place

because the ECP is not a substitute for the remote control.

lDo not disconnect cables from the ECP to connect peripherals because you could

disconnect controls for your interactive whiteboard or host computer.

lPut your SMART product into Standby mode before cleaning it.

lFollow these guidelines to clean the projector:

oWipe the exterior of the projector with a lint-free cloth.

oIf necessary, use a soft cloth moistened with a mild detergent to clean the projector

housing.

oDo not use abrasive cleaners, waxes or solvents.

oAvoid touching the lens. If it is necessary to clean the lens:

oUse liquids or commercial solvents (such as glass cleaners) to clean the lens,

but do not spray them directly on the system.

oUse protective gloves and dip a lint-free cloth (such as Purestat PW2004) in an

anti-static solvent (such as Hyperclean EE-6310).

oGently wipe the lens from the center to the edge.

lDisconnect the product from its power source when it’s not used for a long period.

I M P O R T A N T I N F O R M A T I O N

Environmental requirements

Before installing your SMART Board 600i5 or D600i5 interactive whiteboard system, review the

following environmental requirements.

Environmental

requirement

Parameter

Operating temperature l41°F to 95°F (5°C to 35°C) from 0' to 6000' (0 m to 1800 m)

l41°F to 86°F (5°C to 30°C) from 6000' to 9800' (1800 m to 3000 m)

Storage temperature l-40°F to 122°F (-40°C to 50°C)

Humidity l30% to 80% relative humidity, non-condensing

lHumidity above 80% might cause slight wrinkling in the screen

surface sheet. The wrinkles disappear when the humidity lowers.

Water and fluid

resistance

lIntended for indoor use only. Doesn’t meet any salt-spray or water

ingress requirements.

lDon’t pour or spray liquids directly onto your interactive whiteboard,

the SMART UF75 or UF75w projector or any of its sub-components.

Dust lIntended for use in office and classroom environments. Not for

industrial use where heavy dust and pollutants can cause

malfunctions or impaired operation. Periodic cleaning is required in

areas with heavier dust. See Cleaning the projector on page 33 for

information on cleaning the SMART UF75 or UF75w projector.

lDesigned for pollution degree 1 (P1) as per EN61558-1, which is

defined as “No pollution or only dry non-conductive pollution”

Electrostatic discharge

(ESD)

lEN61000-4-2 severity level 4 for direct and indirect ESD

lNo malfunction or damage up to 8kV (both polarities) with a 330

ohm, 150 pF probe (air discharge)

lUnmated connectors meet no malfunction or damage up to 4kV

(both polarities) for direct (contact) discharge

Cables lAll SMART Board 600i5 or D600i5 interactive whiteboard system

cables should be shielded to prevent potential accidents and

degraded video and audio quality.

Conducted and radiated

emissions

lEN55022/CISPR 22, Class A

I M P O R T A N T I N F O R M A T I O N

Contents
Important information i
Safety warnings, cautions and important information i
Environmental requirements vi
About your interactive whiteboard system 1
SMART Board 600i5 or D600i5 interactive whiteboard system features 2
Included accessories 4
Optional accessories 5
Installing your interactive whiteboard system 7
Choosing a location 8
Choosing a height 8
Routing the cables 9
Installing SMART software 10
Securing the interactive whiteboard system 10
Using your interactive whiteboard system 11
Using your projector 11
Using your interactive whiteboard 23
Using the Extended Control Panel (ECP) 23
Integrating other devices 27
Video format compatibility 27
Connecting peripheral sources and outputs 31
Maintaining your interactive whiteboard system 33
Maintaining your interactive whiteboard 33
Cleaning the projector 33
Focusing and adjusting the projector image 34
Replacing the projector lamp 35
Troubleshooting your interactive whiteboard system 41
Correcting image alignment issues 42
Diagnosing issues using the interactive whiteboard system indicators and controls 42
Resolving network communication issues 47
Resolving audio issues 48
Resolving video issues 48
Resolving image issues 49
Accessing the service menu 52
vii

Locating serial numbers 53

Transporting your interactive whiteboard system 54

Remotely managing your interactive whiteboard system 55

Web page management 56

Connecting your room control system to the SMART UF75 or UF75w projector 63

Projector programming commands 65

Simple Network Management Protocol (SNMP) 76

Disabling user USB access 77

Hardware environmental compliance 81

Waste Electrical and Electronic Equipment regulations (WEEE directive) 81

Restriction of Certain Hazardous Substances (RoHS directive) 81

Batteries 81

Packaging 82

China’s Electronic Information Products regulations 82

U.S. Consumer Product Safety Improvement Act 82

Customer support 83

Online information and support 83

Training 83

Technical support 83

Shipping and repair status 83

General inquiries 84

Warranty 84

Registration 84

Index 85

C O N T E N T S

viii

Inhaltsverzeichnis

Andere SMART Board Interaktives Whiteboard Handbücher

SMART Board

SMART Board Board E70 Bedienungsanleitung

SMART Board

SMART Board SB800ix2 Bedienungsanleitung

SMART Board

SMART Board 600i4 Bedienungsanleitung

SMART Board

SMART Board Board 600 Series Bedienungsanleitung

SMART Board

SMART Board Board X800i4 Bedienungsanleitung

SMART Board

SMART Board SB680-MP Bedienungsanleitung

SMART Board

SMART Board SBID8055i-G5-SMP Service-Handbuch

SMART Board

SMART Board 880i5-SMP Bedienungsanleitung

SMART Board

SMART Board Board 2000i Bedienungsanleitung

SMART Board

SMART Board 3000i Bedienungsanleitung

SMART Board

SMART Board 6052i Bedienungsanleitung

SMART Board

SMART Board Board 480 Bedienungsanleitung

SMART Board

SMART Board 400 series Einrichtungshandbuch

SMART Board

SMART Board 690 Bedienungsanleitung

SMART Board

SMART Board Board 600iv Bedienungsanleitung

SMART Board

SMART Board 480iv2 Bedienungsanleitung

SMART Board

SMART Board M600 series Bedienungsanleitung

SMART Board

SMART Board Board 600 Series Bedienungsanleitung

SMART Board

SMART Board Board X800 Series Bedienungsanleitung

SMART Board

SMART Board 680 Bedienungsanleitung

SMART Board

SMART Board 800i5e-MP series Bedienungsanleitung

SMART Board

SMART Board X800ix Bedienungsanleitung

SMART Board

SMART Board M685ix2 Bedienungsanleitung

SMART Board

SMART Board 600i Series Bedienerhandbuch

Beliebte Interaktives Whiteboard Handbücher anderer Marken

SMART

SMART KAPP42 Bedienungsanleitung

Buhl

Buhl LyteBoard Bedienungsanleitung

SMART

SMART SBX880 Bedienungsanleitung

Legamaster

Legamaster e-SCREEN ETX Bedienungsanleitung

Seneca

Seneca eno Bedienungsanleitung

BenQ

BenQ RP840G Bedienungsanleitung

SMART

SMART Sympodium IC-150 Bedienungsanleitung

Olivetti

Olivetti OLIBOARD Bedienungsanleitung

Turning Technologies

Turning Technologies MOBIVIEW Bedienungsanleitung

Panasonic

Panasonic UB-5335 Bedienungsanleitung

Dukane

Dukane ITP84 Bedienungsanleitung

Bretford

Bretford EDUIMS Konfigurationshandbuch

Panasonic

Panasonic Panaboard UB-5315 Bedienungsanleitung

Plus

Plus M-11S Bedienungsanleitung

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Bedienungsanleitung

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Bedienungsanleitung

AVer

AVer CP series Bedienungsanleitung

Genee

Genee 56" Bedienungsanleitung