SMART Board SmartBoard 600i2 Bedienungsanleitung

Conﬁguration and User’s Guide

SMART Board™ 600i2

Interactive Whiteboard System

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

manufacturer’s instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Trademark Notice

SMART Board, GoWire, Unifi, smarttech and the SMART logo are trademarks or registered trademarks of SMART

Technologies ULC in the U.S. and/or other countries. Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by

SMART Technologies ULC under license. All other third-party product and company names may be the trademarks of their

respective owners.

stored in a retrieval system or translated into any language in any form by any means without the prior written consent of

SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the

part of SMART.

Patent No. US5448263; US6141000; US6320597; US6326954; US6337681; US6540366; US6741267; US6747636; US7151533; US7289113;

US7283126; and CA2058219. Other patents pending.

Printed in Canada. 12/2008

If you register your SMART product, we’ll notify you of new features and

software upgrades.

www.smarttech.com/registration.

Keep the following information available, in case you need to contact

Technical Support:

Serial Number

Date of Purchase

Registration Benefits

99-00850-21 B0 Important Information i

Important Information

Read This Section First

IMPORTANT

NOTE: If you own a SMART product other than a SMART Board™ 600i2 interactive whiteboard system, refer to

the installation guide that came with your product for relevant warnings and maintenance instructions.

In this document, “SMART Board 600i2 interactive whiteboard system” refers to the SMART Board 600 series

interactive whiteboard and its Unifi™ 45 projector, accessories and optional equipment. Read the safety

warnings and precautions that came with the peripheral products, such as the interactive whiteboard and

additional SMART accessories.

Before you install and use the SMART Board 600i2 interactive whiteboard system, read and understand the

safety warnings and precautions in this SMART Board 600i2 Interactive Whiteboard System’s Installation Guide

(document 118923) and the Important Information Warnings Document (document 124023). These safety

warnings and precautions describe the safe and correct operation of the SMART Board 600i2 interactive

whiteboard system and its accessories, helping you prevent injuries and equipment damage. You must always

ensure that the interactive whiteboard system is being used correctly.

The Unifi 45 projector included with your SMART Board 600i2 interactive whiteboard system is designed to work

only with certain SMART Board interactive whiteboard models. Contact your authorized SMART reseller for more

information.

SMART Technologies frequently updates this document to provide accurate support. For

the most recent version of this document, see (document 118924)on the SMART Technical

Support website.

ii Important Information 99-00850-21 B0

Safety Warnings

WARNING • Make sure that an electrical socket is near to your SMART Board product and remains easily

accessible during use.

• Ensure that any cables extending across the floor to your SMART Board product are

properly bundled and marked to prevent a trip hazard.

• Failure to follow the installation instructions shipped with your SMART Board product could

result in personal injury and damage to the product.

• You must connect the USB cable that came with your SMART Board interactive whiteboard

to a computer that has a USB compliant interface and that bears the USB logo. In addition,

the USB source computer must be compliant with CSA/UL/EN 60950 and bear the CE mark

and CSA and/or UL Mark(s) for CAS/UL 60950. This is for operating safety and to prevent

damage to the SMART Board interactive whiteboard.

• To reduce the risk of fire or electric shock, do not expose any component of your SMART

Board interactive whiteboard system to rain or moisture.

• Refer to the safety warnings and precautions published by the projector manufacturer. Do

not stare (or allow children to stare) directly into the projector’s beam of light.

• Do not stand (or allow children to stand) on a chair to touch the surface of your SMART

Board product. Rather, wall-mount the product at the appropriate height or use a SMART

height-adjustable floor stand.

• Do not climb (or allow children to climb) on any part of

your wall-mounted SMART Board interactive whiteboard

system.

• Do not climb on, hang from or suspend objects from the

Unifi 45 projector’s arm.

• To attach the wall tether, use the appropriate hardware

for your wall type. Failure to do so could result in injury if

the unit detaches from the wall.

• Climbing on the interactive whiteboard or projector arm

could result in personal injury or product damage.

• Do not attempt to service the projector other than

performing routine lamp replacement and cleaning the

mirror. Service should be performed only by an

authorized service provider. Other than the lamp module, there are no user serviceable parts

inside the unit.

• Do not remove any screws other than those specified in the lamp replacement instructions.

• Do not stare into the beam of light created by the projector. Instruct children not to look in the

direction of, or stare at, this beam of light. Encourage users to keep their back to the

projector when working at the interactive whiteboard. Before they turn to face the audience,

users should step sideways, out of the projector’s beam.

• Tell users not to touch the head or lens of the projector, as it can become extremely hot

during normal operation.

WARNING • If the projector is mounted on the arm, the manufacturer recommends contacting your

authorized SMART reseller when the lamp must be exchanged.

• Only qualified personnel should replace the projector lamp. Replacing the lamp in a

arm-mounted projector might result in a fall and injury.

• If you continue to use the projector after the replacement message appears, the lamp might

shatter or burst, scattering glass throughout the projector head.

• If the lamp has shattered or burst, do not touch the glass fragments because they might

cause injury. Leave and then ventilate the area where the lamp shattered or burst. Wash

your hands thoroughly if you have come into contact with lamp debris. Thoroughly clean the

area around the projector, and discard any edible items placed in that area because they

might be contaminated.

• If the lamp has shattered or burst, call a SMART authorized service representative for

instructions. Do not attempt to replace the lamp.

• Remove the projector from the arm before servicing the lamp.

• Complete the procedure described in this document before following the instructions

included in your replacement lamp box.

• Uncovering the lamp while the projector is mounted on an arm might lead to product damage

or personal injury from falling pieces of glass if the lamp is broken.

• Turn the projector off and wait 15 minutes for the lamp to cool completely before removing

the old lamp assembly.

• Wear protective eyewear while changing the lamp. Failure to do so can cause injury or loss

of eyesight if the lamp shatters or bursts.

• The lamp used in the Unifi 45 projector contains mercury. Recycle or dispose of it as

hazardous waste, in accordance with local regulations.

• To prevent premature lamp failure or exposure to mercury, always handle the fragile lamp

assembly with care. Use gloves when touching the lamp. Do not touch the lamp with your

fingers.

• Use only the SB20 replacement lamp (SMART Part No. 01-00247).

• Never replace the lamp assembly with a previously used lamp assembly.

• When mounting the projector on a framed wall, you must attach both the mounting bracket

and safety tether to a stud to safely support the projector’s weight. If you only use drywall

anchors, the drywall can fail, resulting in product damage and possible personal injury.

• If the two screws supporting the safety tether are removed, the projector boom will be free to

swing. Make sure that these two screws are tightened and never remove them from the unit

without supporting the projector arm first.

• Two people are required to mount the projector and the interactive whiteboard on a wall

because they might be too heavy for one person to maneuver onto their wall-mounting

brackets.

• Cleaning a arm-mounted projector may result in a fall and injury.

99-00850-21 B0 Important Information iii

CAUTION • Never operate this unit immediately after moving it from a cold location to a warm location.

When the unit is exposed to such a change in temperature, moisture may condense on the

lens and crucial internal parts. Allow the system to stabilize to room temperature before

operation to prevent the unit from possible damage.

• In a high altitude location where air is thin, cooling efficiency is reduced so use the projector

with fan mode set to High.

• Do not place in hot locations, such as near heating equipment. Doing so could cause a

malfunction and shorten the life of the projector.

• Before you clean the Unifi 45 projector, turn off the power button switch on the projector, not

the ECP

, and allow bulb to cool. Depressing the ECP button at this time would cause the

projector to start back up.

• Do not allow liquids or commercial solvents of any kind to flow into the projector base or

head. Do not use spray cleaners or solvents near any part of the projector, as it may damage

or stain the unit.

• Cycling power to the projector repeatedly can lock or damage the interactive whiteboard

system. Allow at least 15 minutes for cooling before sending the ON command after turning

off the system.

• After you turn the system off, wait until the system cools completely before turning the

system on again. Avoid cycling the system off and on.

• Do not connect your serial cable directly to the projector’s RS-232 serial interface. The

extended control panel’s (ECP’s) RS-232 serial interface is the only recommended

connection point.

IMPORTANT • Using the Unifi 45 projector system near a TV or radio may cause interference to the images

or audio sound. If this happens, move the TV or radio away from the projector.

• Securing the pen tray can provide theft deterrence for the interactive whiteboard as well.

The screws that secure the interactive whiteboard to the wall are located directly behind the

pen tray. The pen tray must be removed before you can remove the interactive whiteboard.

When you secure the pen tray, you also secure the interactive whiteboard.

• Install your host computer’s video output directly to your Unifi 45 projector and not to

the ECP. The VGA connector on the ECP is then available for a guest computer connection,

such as a laptop. If you will not have guest computers, you can use the VGA connector on

the ECP instead.

• Only use the input marked “Computer 2” on your projector to connect the ECP

harness cable.

• The 600i2 interactive whiteboard system does not have speakers. Consult your authorized

SMART reseller to determine your audio output options.

• If you have peripheral devices that do not use a 4-pin mini-DIN connectors or an RCA

composite video jack, or if your device has an audio connection that does not use RCA

jacks, you might need to purchase third-party adapters.

• After you resolve your projector’s issue, you must turn your projector’s main power switch off

and on again to clear the indicator light sequence and reset your projector’s status.

iv Important Information 99-00850-21 B0

99-00850-21 B0 Important Information v

Other Precautions

To ensure operating safety and to avoid product damage, observe the following precautions.

• Do not set up or use the interactive whiteboard in an area with excessive levels of dust, humidity and

smoke.

• Do not add extra weight or apply pressure to the Unifi 45 projector arm, the wall-mounted interactive

whiteboard or its pen tray. SMART Technologies designed the brackets to support only the weight of the

components during normal use.

• To reduce the risk associated with leaking batteries:

– use only AA type batteries

– do not mix used and new batteries

– orient the battery’s plus (+) and minus (-) terminals according to the markings found on the remote

control

– do not leave the batteries in the remote control for an extended period

– do not heat, disassemble, short or recharge the batteries, or expose them to fire or high temperature

– avoid eye and skin contact if batteries have leaked

– dispose of exhausted batteries and product components in accordance with applicable regulations

• If the interactive whiteboard system requires replacement parts, make sure the service technician uses

replacement parts specified by SMART Technologies, or parts with the same characteristics as the original.

Transporting the SMART Board 600i2 Interactive Whiteboard System

If you need to ship any part of your SMART Board 600i2 interactive whiteboard system, repack it with the original

packaging. If the original packaging is no longer available, you may purchase replacement packaging from your

authorized SMART reseller.

If you prefer to use your own packaging materials, make sure you adequately protect the unit. Ship the

interactive whiteboard in an upright position to deter shippers from placing heavy objects on it.

vi Important Information 99-00850-21 B0

99-00850-21 B0 Table of Contents vii

Table of Contents

Important Information i

Read This Section First................................................................................................................................... i

Safety Warnings............................................................................................................................................. ii

Other Precautions .......................................................................................................................................... v

Transporting the SMART Board 600i2 Interactive Whiteboard System ......................................................... v

Table of Contents vii

About Your 600i2 Interactive Whiteboard System 1

SMART Board 600i2 Interactive Whiteboard System Features ..................................................................... 2

Standard Accessories .................................................................................................................................... 3

Optional Accessories ..................................................................................................................................... 4

Before Installing Your 600i2 Interactive Whiteboard System 7

Environmental Requirements......................................................................................................................... 7

Before Installing Your SMART Board 600i2 Interactive Whiteboard System ................................................. 8

After Installing Your 600i2 Interactive Whiteboard System .......................................................................... 10

Connecting Your 600i2 Interactive Whiteboard System 21

Installing SMART Notebook Software .......................................................................................................... 21

Connecting Your Computer to the Interactive Whiteboard System .............................................................. 22

Using Your 600i2 Interactive Whiteboard System 25

After Completing the Installation .................................................................................................................. 25

Using Your ECP ...........................................................................................................................................25

Using Your Interactive Whiteboard............................................................................................................... 26

Using Your Unifi 45 Projector ....................................................................................................................... 26

Adjusting Your Projector Settings................................................................................................................. 27

Maintaining Your 600i2 Interactive Whiteboard System 31

Preventing Damage to Your Interactive Whiteboard .................................................................................... 31

Cleaning Your Interactive Whiteboard.......................................................................................................... 31

Cleaning the Pen Tray ................................................................................................................................. 32

Cleaning the Unifi 45 Projector ................................................................................................................... 33

Preparing to Replace the Projector Lamp .................................................................................................... 33

Troubleshooting Your 600i2 Interactive Whiteboard System 41

System Warning Lights ................................................................................................................................ 41

Remote Management of Your 600i2 Interactive Whiteboard System 47

Programming Commands for Managing Your 600i2 Interactive Whiteboard

System Settings ........................................................................................................................................... 47

Command Inventory..................................................................................................................................... 49

viii Table of Contents 99-00850-21 B0

Regulatory Compliance 55

Waste Electrical and Electronic Equipment Regulations..............................................................................55

Restriction of Certain Hazardous Substances (RoHS) Directives................................................................56

Customer Support 57

Online Information and Support ...................................................................................................................57

Training ........................................................................................................................................................57

Technical Support.........................................................................................................................................57

Shipping and Repair Status..........................................................................................................................57

General Inquiries.......................................................................................................................................... 57

Registration ..................................................................................................................................................57

Warranty.......................................................................................................................................................58

Index 59

Inhaltsverzeichnis

Andere SMART Board Interaktives Whiteboard Handbücher

SMART Board

SMART Board 800i5e-MP series Bedienungsanleitung

SMART Board

SMART Board SBID8055i-G5-SMP Bedienungsanleitung

SMART Board

SMART Board Board X800i4 Bedienungsanleitung

SMART Board

SMART Board Board 600 Series Bedienungsanleitung

SMART Board

SMART Board SB880i4 Bedienungsanleitung

SMART Board

SMART Board 880-SMP Bedienungsanleitung

SMART Board

SMART Board 680iv Bedienungsanleitung

SMART Board

SMART Board Board 600iv Bedienungsanleitung

SMART Board

SMART Board M600i6 Bedienungsanleitung

SMART Board

SMART Board Board X800 Series Bedienungsanleitung

SMART Board

SMART Board SBID 8055i Bedienungsanleitung

SMART Board

SMART Board M600 series Bedienungsanleitung

SMART Board

SMART Board 600i3 Bedienungsanleitung

SMART Board

SMART Board Board E70 Bedienungsanleitung

SMART Board

SMART Board SB685ix2 Bedienungsanleitung

SMART Board

SMART Board Board 2000i Bedienungsanleitung

SMART Board

SMART Board 400 series Einrichtungshandbuch

SMART Board

SMART Board SB800ix2 Bedienungsanleitung

SMART Board

SMART Board 800i6 Bedienungsanleitung

SMART Board

SMART Board 7000 series Bedienungsanleitung

SMART Board

SMART Board 8070i-G4-SMP Betriebsanleitung

SMART Board

SMART Board M600ix3 Bedienungsanleitung

SMART Board

SMART Board Board E70 Bedienungsanleitung

SMART Board

SMART Board Board 480 Bedienungsanleitung

Beliebte Interaktives Whiteboard Handbücher anderer Marken

SMART

SMART KAPP42 Bedienungsanleitung

Buhl

Buhl LyteBoard Bedienungsanleitung

SMART

SMART SBX880 Bedienungsanleitung

Legamaster

Legamaster e-SCREEN ETX Bedienungsanleitung

Seneca

Seneca eno Bedienungsanleitung

BenQ

BenQ RP840G Bedienungsanleitung

SMART

SMART Sympodium IC-150 Bedienungsanleitung

Olivetti

Olivetti OLIBOARD Bedienungsanleitung

Turning Technologies

Turning Technologies MOBIVIEW Bedienungsanleitung

Panasonic

Panasonic UB-5335 Bedienungsanleitung

Dukane

Dukane ITP84 Bedienungsanleitung

Bretford

Bretford EDUIMS Konfigurationshandbuch

Panasonic

Panasonic Panaboard UB-5315 Bedienungsanleitung

Plus

Plus M-11S Bedienungsanleitung

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Bedienungsanleitung

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Bedienungsanleitung

AVer

AVer CP series Bedienungsanleitung

Genee

Genee 56" Bedienungsanleitung