SMART Board 685ix Bedienungsanleitung

SMART Board 

685ix Interactive

Whiteboard System

Condensed Configuration

and User’s Guide

IMPORTANT

SMART Technologies frequently

updates this document to provide

accurate support. For the most

recent version of this document 

(in English) visit the SMART

Support website at

http:\\smarttech.com\st\en-

us\support.

Product Registration

If you register your SMART product, we’ll notify you of new features and software

upgrades.

Keep the following information available in case you need to contact SMART

Technical Support.

Serial Number: ___________________________________________________

Date of Purchase: ___________________________________________________

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Trademark Notice

SMART Board, The SMART logo, GoWire and smarttech are trademarks or registered trademarks of SMART Technologies

ULC in the U.S. and/or other countries. EXPO and Sanford are registered U.S. trademarks of SANFORD or its affiliates.

VESA is a registered trademark of The Video Electronics Standards Association. Windows is either a registered trademark

or a trademark of Microsoft Corporation in the U.S. and/or other countries. All other third-party product and company names

may be trademarks of their respective owners.

transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written

consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not

represent a commitment on the part of SMART.

SMART Board™ 685ix interactive whiteboard system Patent No. US5448263; US6141000; US6320597; US6326954;

US6337681; US6540366; US6741267; US6747636; US7151533; US72891133; US7499033; CA2058219; and

CA2252302. Other patents pending. UX60 projector system Patent No. US6540366. Other patents pending.

08/2009

Part No. 99-00984-20 REV A0

Introduction

Important Information

Read This Section First

NOTE

If you own a SMART product other than a SMART Board™ 685ix interactive

whiteboard system, refer to the installation guide that came with your product for

relevant warnings and maintenance instructions.

In this document, “SMART Board 685ix interactive whiteboard system” refers to the

SMART Board 685 interactive whiteboard and its UX60 projector, accessories and

optional equipment. Before you install and use the SMART Board 685ix interactive

whiteboard system, read and understand the safety warnings and precautions in this

user’s guide, the interactive whiteboard user’s guide and the warnings document.

These safety warnings and precautions describe the safe and correct operation of the

interactive whiteboard system and its accessories, helping you prevent injuries and

equipment damage. You must always ensure that the interactive whiteboard system is

being used correctly.

The UX60 projector included with your system is designed to work with certain

SMART Board interactive whiteboard models only. Contact your authorized SMART

reseller for more information.

Safety Warnings, Cautions and Important Information

WARNINGS – GENERAL

• Do not climb (or allow children to climb) on any

part of your wall-mounted SMART Board

interactive whiteboard system.

• Climbing on the interactive whiteboard or

projector boom could result in personal injury or

product damage. Do not climb on, hang from or

suspend objects from the UX60 projector.

• To reduce the risk of fire or electric shock, do not

expose any component of your SMART Board

interactive whiteboard system to rain or moisture.

ii | INTRODUCTION – IMPORTANT INFORMATION

Part No. 99-00984-20 REV A0

• Failure to follow the installation instructions shipped with your SMART product

could result in personal injury and damage to the product.

• If you remove the three screws

supporting the adjustment module,

the projector will be free to move on

the wall-mounting bracket’s track.

Make sure that the screws are

tightened.

• Make sure that an electrical socket is

near your SMART product and

remains easily accessible during use.

• Two people are required to mount 

the projector and the interactive

whiteboard on a wall because they

could be too heavy for one person to

maneuver onto their wall-mounting

brackets.

• When mounting the projector on a

framed or hollow wall, you must

attach both the mounting bracket and

safety tether to a stud to safely

support the projector’s weight. If you

use only drywall anchors, the drywall

can fail, resulting in product damage

and possible personal injury.

Part No. 99-00984-20 REV A0

iii | INTRODUCTION – IMPORTANT INFORMATION

• When adjusting the projector’s image, only loosen the locking screw next to

the lock and unlock symbols (see the following illustration in grey). Never

loosen other screws or loosen the center nut attached to the projector bolt as

your projector may fall.

• Ensure that any cables extending across the floor to your SMART product are

properly bundled and marked to prevent a trip hazard.

• Cleaning a wall-mounted projector can result in a fall or injury. Use caution

when climbing a ladder, or remove the projector from the wall-mounting

bracket to clean it.

WARNINGS – PROJECTOR

• Do not stare (or allow children to stare) directly into the beam of light created

by the projector. Instruct children not to look in the direction of, or stare at, this

beam of light. Encourage users to keep their back to the projector when

working at the interactive whiteboard. Before they turn to face the audience,

users should step sideways, out of the projector’s beam.

• Do not attempt to service the projector other than performing routine lamp

replacement. Other than the lamp module, there are no user-serviceable

parts inside the unit. Do not open or disassemble the projector as this may

cause electric shock.

• This projector detects its remaining lamp life. Replace the lamp when a lamp

life warning message appears. If you continue to use the projector after the

replacement message appears, the lamp can shatter or burst, scattering

glass throughout the projector.

iv | INTRODUCTION – IMPORTANT INFORMATION

Part No. 99-00984-20 REV A0

• If the lamp has shattered or burst:

– Call an authorized SMART reseller for instructions. Do not attempt to

replace the lamp.

– Do not touch the glass fragments because they can cause injury.

– Leave and then ventilate the area where the lamp shattered or burst.

– Wash your hands thoroughly if you have come into contact with 

lamp debris.

– Thoroughly clean the area around the projector, and discard any edible

items placed in that area because they could be contaminated.

• Replacing the lamp in a wall-mounted projector can result in a fall or injury.

Use caution when climbing a ladder, or remove the projector from the wall-

mounting bracket to replace the lamp.

– Uncovering the lamp while the projector is mounted on the wall-mounting

bracket can lead to product damage or personal injury from falling pieces

of glass if the lamp is broken.

• When replacing the projector lamp:

– Turn off the projector and wait 30 minutes for the lamp to cool 

completely (or before removing the projector from the wall-mounting

bracket, if necessary).

– Do not remove any screws other than those specified in the lamp

replacement instructions.

– Wear protective eyewear while changing the lamp. Failure to do so can

cause injury or loss of eyesight if the lamp shatters or bursts.

– Use only replacement lamps approved by SMART Technologies. Contact

your authorized SMART reseller for replacement parts.

– Never replace the lamp assembly with a previously-used lamp assembly.

– To prevent premature lamp failure or exposure to mercury, always handle

the fragile lamp assembly with care. Use gloves when touching the lamp.

Do not touch the lamp with your fingers.

– Recycle or dispose of the lamp as hazardous waste, in accordance with

local regulations.

• When returning the projector to the wall-mounting bracket, replace all of the

screws you removed when you removed the projector. Failure to do so 

can result in the projector falling from the boom resulting in injury or

equipment damage.

Part No. 99-00984-20 REV A0

v | INTRODUCTION – IMPORTANT INFORMATION

• Reduce the risk associated with a leaking battery in your projector’s remote

control:

– Use only the specified coin-cell type battery

– Orient the battery’s plus (+) and minus (-) terminals according to the

markings on the remote control

– Remove the battery when the remote control is unused for an extended

period

– Do not heat, disassemble, short or recharge the battery, or expose it to

fire or high temperatures

– Avoid eye and skin contact if the battery has a leak

– Dispose of the exhausted battery and product components in accordance

with applicable regulations

CAUTIONS

• Avoid turning off the projector during the lamp ignition phase because this can

lead to premature lamp failure. Before turning off the projector, keep the lamp

on for a minimum of 15 minutes after turning it on to preserve the lamp life.

• When you switch the projector off, ensure that the cooling cycle is complete

before disconnecting the power. Allow 90 seconds for the projector to

complete the cooling cycle.

• Never operate this unit immediately after moving it from a cold location to a

warm location. When the unit is exposed to such a change in temperature,

moisture can condense on the lens and crucial internal parts. Allow the

system to reach room temperature before operation to prevent possible

damage to the unit.

• In a high altitude location where the altitude is over 6000' (1829 m), where the

air is thin, cooling efficiency is reduced, so use the projector with the fan mode

set to High.

• Do not block the projector’s ventilation slots and openings.

• Do not place in hot locations, such as near heating equipment. Doing so could

cause a malfunction and shorten the life of the projector.

• Do not set up or use the interactive whiteboard system in an area with

excessive levels of dust, dirt, humidity or smoke.

• Before you clean the UX60 projector, put the system into Idle mode by

pressing the power button twice on the ECP or remote and allow the bulb to

cool for at least 30 minutes.

vi | INTRODUCTION – IMPORTANT INFORMATION

Part No. 99-00984-20 REV A0

• Do not allow liquids or commercial solvents of any kind to flow into the

projector base or head. Do not use spray cleaners or solvents near any part of

the projector, because they can damage or stain the unit.

• Cycling power to the projector repeatedly can lock or damage the interactive

whiteboard system. After you turn off the system, wait at least 15 minutes for

cooling before turning on the system.

• You must connect the USB cable that came with your SMART Board

interactive whiteboard to a computer that has a USB compliant interface and

that bears the USB logo. In addition, the USB source computer must be

compliant with CSA/UL/EN 60950 and bear the CE mark and CSA and/or UL

mark(s) for CAS/UL 60950. This is for operating safety and to prevent

damage to the SMART Board interactive whiteboard.

• Do not add extra weight or apply pressure to the UX60 projector boom, the

wall-mounted interactive whiteboard or its pen tray. SMART Technologies

designed the brackets to support only the weight of the components during

normal use.

• If the interactive whiteboard system requires replacement parts, make sure

that the service technician uses replacement parts specified by SMART

Technologies, or parts with the same characteristics as the original.

IMPORTANT

• Turn off the SMART product before cleaning it.

• Using the UX60 projector system near a TV or radio can cause interference 

to the images or sound. If this happens, move the TV or radio away from 

the projector.

• Do not place the interactive whiteboard system near any appliance that

generates a strong magnetic field.

• Do not place the interactive whiteboard system in direct sunlight.

• The screws that secure the interactive whiteboard to the wall are located

directly behind the pen tray. The pen tray must be removed before you can

remove the interactive whiteboard. When you secure the pen tray, you also

secure the interactive whiteboard.

• The SMART Board 685ix interactive whiteboard system does not include

speakers. Consult your authorized SMART reseller to determine your audio

output options.

• If you have peripheral devices that do not use a 4-pin mini-DIN connector, an

HDMI connector or an RCA composite video jack, or if your device has an

audio connection that does not use RCA jacks or 3.5 mm plugs, you might

need to purchase third-party adapters.

Part No. 99-00984-20 REV A0

vii | INTRODUCTION – IMPORTANT INFORMATION

• Disconnect the product from its power source when it is not used for a 

long period.

• When cleaning the interactive whiteboard system:

– Wipe the exterior of the projector using a lint-free cloth

– If necessary, use a soft cloth moistened with a mild detergent to clean the

projector housing.

– Do not use abrasive cleaners, waxes or solvents

Transporting the SMART Board 685ix Interactive 

Whiteboard System

If you need to ship any part of your SMART Board 685ix interactive whiteboard

system, repack it with the original packaging. If the original packaging is no longer

available, you can purchase replacement packaging from your authorized SMART

reseller.

If you prefer to use your own packaging materials, make sure that you adequately

protect the unit. Ship the interactive whiteboard in an upright position to deter shippers

from placing heavy objects on it.

viii | INTRODUCTION – IMPORTANT INFORMATION

Part No. 99-00984-20 REV A0

Andere Handbücher für Board 685ix

Inhaltsverzeichnis

Andere SMART Interaktives Whiteboard Handbücher

SMART

SMART M600i6 Bedienungsanleitung

SMART

SMART 2000i-DVS Bedienungsanleitung

SMART

SMART kapp 84 Bedienungsanleitung

SMART

SMART SBX880 Bedienungsanleitung

SMART

SMART KAPP42 Bedienungsanleitung

SMART

SMART 600i Bedienungsanleitung

SMART

SMART SBM600i6 Bedienungsanleitung

SMART

SMART Board E70 Betriebsanleitung

SMART

SMART Board 600i4 Bedienungsanleitung

SMART

SMART Board 6000 Series Bedienungsanleitung

SMART

SMART Sympodium IC-150 Bedienungsanleitung

SMART

SMART Smart Board 480 Bedienungsanleitung

SMART

SMART SBX885 Bedienungsanleitung

SMART

SMART Board 885ix2-NCP Bedienungsanleitung

SMART

SMART Board 600 Series Bedienungsanleitung

SMART

SMART SB880i5-MP Bedienungsanleitung

SMART

SMART Board 600 Series Betriebsanleitung

SMART

SMART SMART Board 885-SMP Bedienungsanleitung

SMART

SMART Table 230i Bedienungsanleitung

SMART

SMART 8070i-G4-SMP Betriebsanleitung

SMART

SMART SBID-7286 Bedienungsanleitung

SMART

SMART 600i Bedienungsanleitung

SMART

SMART board 8000i-G4 series Betriebsanleitung

SMART

SMART UF45-680 Bedienungsanleitung

Beliebte Interaktives Whiteboard Handbücher anderer Marken

HitachiSoft

HitachiSoft StarBoard FX-TRIO-88W Bedienungsanleitung

Buhl

Buhl LyteBoard Bedienungsanleitung

SMART Board

SMART Board 680 Bedienungsanleitung

Legamaster

Legamaster e-SCREEN ETX Bedienungsanleitung

SMART Board

SMART Board SBM685ix2 Bedienungsanleitung

Seneca

Seneca eno Bedienungsanleitung

BenQ

BenQ RP840G Bedienungsanleitung

Olivetti

Olivetti OLIBOARD Bedienungsanleitung

Turning Technologies

Turning Technologies MOBIVIEW Bedienungsanleitung

Panasonic

Panasonic UB-5335 Bedienungsanleitung

Dukane

Dukane ITP84 Bedienungsanleitung

Bretford

Bretford EDUIMS Konfigurationshandbuch

Panasonic

Panasonic Panaboard UB-5315 Bedienungsanleitung

Plus

Plus M-11S Bedienungsanleitung

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Bedienungsanleitung

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Bedienungsanleitung

AVer

AVer CP series Bedienungsanleitung

Genee

Genee 56" Bedienungsanleitung