Smarte 4K-8x8-L Bedienungsanleitung

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 2

SYMBOLS

To ensure the safe and correct use of equipment, we use a range of symbols on the equipment and in the

manuals. These symbols demonstrate the risk of physical harm or possible damage to property for the user

or others and provide guidance on standards and disposal. Symbol indications and their meanings are as

follows. Please ensure that you correctly understand these instructions before reading the manual and

operating the equipment.

WARNING. This symbol is used to indicate where important instructions are provided to

ensure the correct operation of the equipment and user safety.

To prevent fire or shock hazards, do not expose this equipment to rain or moisture. Also,

do not use this equipment’s polarized plug with an extension cord receptacle or other

outlets unless the prongs can be fully inserted. Refrain from opening the cabinet as there

are high voltage components inside. Please refer all servicing to qualified service personnel.

This symbol warns user that uninsulated voltage within the unit may have sufficient

magnitude to cause an electric shock. Therefore, it is dangerous to make any kind of contact

with any part inside this unit.

This is a WiFi product, which may cause or be susceptible to radio interference. Users may

need to take additional measures to mitigate the interference.

This is a Bluetooth product, which may cause or be susceptible to radio interference. Users

may need to take additional measures to mitigate the interference.

This is an RF Radio product, which may cause or be susceptible to radio interference. Users

may need to take additional measures to mitigate the interference.

This is an Infrared product, which may cause or be susceptible to frequency interference.

Users may need to take additional measures to mitigate the interference.

This is a product which conforms to HDbaseT specification.

This product supports full High Definition 1080p resolution.

This product supports 4K Ultra High Definition resolution.

This product supports 3D definition display.

CE certification means that the product has reached the directive safety requirements

defined by the European Union.

SGS certification means that the product has reached the quality inspection standards

proposed by the world's largest quality standards body - SGS.

This product has passed the ISO9001:2000 international quality certification

EU-wide legislation, as implemented in each Member State, requires that waste electrical

and electronic products carrying the mark (left) must be disposed of separately from

normal household waste. This includes monitors and electrical accessories, such as signal

cables or power cords. When you need to dispose of your equipment, please follow the

guidance of your local authority, or ask the agent where you purchased the product. If you

wish to dispose of used electrical and electronic products outside the European Union,

please contact your local authority so as to comply with the correct disposal method.

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 3

WARNING

In order to ensure the reliable performance of the equipment and the safety of the user, please observe the following

matters during the process of installation, use and maintenance. :

INSTALLATION

Please do not use this product in the following places: places with high levels of dust or soot; places with high electric

conductivity; places with corrosive or combustible gas; places exposed to high temperature, condensation, wind or

rain; places subject to the occasion of vibration or impact.

When installing screw or wiring, make sure that metal scraps and wire heads will not fall into the screw shaft of the

equipment, as it could cause a fire, fault, or incorrect operation.

When the installation work is completed, ensure there is nothing left on the ventilated vents of the equipment, including

packaging items. Blocked vents may cause a fire, fault, incorrect operation.

Avoid wiring and inserting cable plugs in a charged state, otherwise it is easy to cause shock, or electrical damage.

The installation wiring should be strong reliable and earthed.

For installations in areas of high interference, the installer should choose shielded cable as the high frequency signal

input or output cable, so as to improve the anti-interference ability of the system.

Switch off and disconnect the equipment from all power sources prior to handling, installation or wiring, otherwise it

may cause electric shock or equipment damage.

This product grounds to earth by the grounding wires. To avoid electric shocks, grounding wires and the earth must

be linked together. Before the connection of input or output terminals, please make sure this product is correctly

grounded.

All terminals and wiring should be fully sheathed or otherwise covered before connecting the equipment to a power

supply so as to avoid cause electric shock.

OPERATION AND MAINTENANCE

Be sure to read this manual, and fully comply with the safety recommendations, before undertaking maintenance or

operation.

Do not touch terminals whilst the equipment is in a powered state, or it may cause a shock, incorrect operation.

Switch off and disconnect the equipment from all power sources prior to cleaning or tightening terminals or

connections. These operations can lead to electric shock in a live current state.

Switch off and disconnect the equipment from all power sources prior to the connection or disconnection of

communication signal cables, expansion modules, or other adapters, or it may cause damage to the equipment,

incorrect operation, or lead to electric shock in a live current state.

Do not dismantle the equipment and avoid damaging the internal electrical components. Please refer all servicing to

qualified service personnel.

DISPOSAL

Be sure to dispose of the equipment in accordance with local regulations.

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 4

CONTENTS

1FUNCTION ............................................................................................................................................................... 5

2FEATURES................................................................................................................................................................ 6

3CHASSIS PANEL DESCRIPTION .............................................................................................................................. 7

4APPLICATION DIAGRAM ......................................................................................................................................... 9

5REMOTE CONTROL INTERFACES...........................................................................................................................10

5.1 RS232 SERIAL CONTROL PORT INTERFACE.............................................................................................................. 10

5.2 TCP/IP CONTROL PORT INTERFACE .......................................................................................................................... 10

5.2.1

TCP/IP CONNECTION VIA SWITCH

.................................................................................................................... 10

5.2.2

TCP/IP CONNECTION DIRECT VIA CROSS-CONNECT

...................................................................................... 10

6WHAT IS INCLUDED...............................................................................................................................................11

7ACCESSORIES ........................................................................................................................................................12

7.1 INFRA-RED RECEIVERS (IR RX)............................................................................................................................................. 12

7.2 INFRA-RED TRANSMITTERS (IR TX) ...................................................................................................................................... 13

7.3 INFRA-RED HANDSET .......................................................................................................................................................... 14

7.4 RACK MOUNTING EARS....................................................................................................................................................... 15

8BASIC SETUP..........................................................................................................................................................16

9STARTUP SEQUENCE.............................................................................................................................................17

10 FRONT PANEL OPERATION................................................................................................................................18

10.1 VIDEO CROSSPOINT SELECTION......................................................................................................................................... 18

10.2 EDID SELECTION............................................................................................................................................................ 21

10.2.1

Read EDID from local hdmi outputs

................................................................................................................ 21

10.2.2

read edid from hdbaset outputs

..................................................................................................................... 24

10.2.3

Set EDID to internal value

................................................................................................................................ 27

10.3 BAUD RATE ADJUSTMENT............................................................................................................................................... 31

10.4 SHUTDOWN TIMER ........................................................................................................................................................ 34

10.5 SYSTEM SETTINGS.......................................................................................................................................................... 37

11 INFRA-RED CONTROL .........................................................................................................................................39

11.1 CROSSPOINT CONTROL.................................................................................................................................................... 41

11.1.1

setting a single crosspoint

............................................................................................................................... 42

11.1.2

setting multiple crosspoints

............................................................................................................................ 44

11.1.3

set all crosspoints simultaneously

.................................................................................................................. 47

11.1.4

set unit to point-to-point mode

......................................................................................................................... 49

11.2 IR SYSTEM CONTROLS..................................................................................................................................................... 50

12 RS232 CONTROL ...............................................................................................................................................51

13 TCP/IP CONTROL ...............................................................................................................................................52

13.1 COMMAND LINE COMMANDS OVER ETHERNET.................................................................................................................... 52

13.2 USING THE INTEGRATED WEB SERVER ............................................................................................................................... 53

13.2.1

setting video crosspoints

.................................................................................................................................54

13.2.2

edid management

............................................................................................................................................ 56

13.2.3

IP and gateway settings

................................................................................................................................... 58

14 HDBASET CABLING ............................................................................................................................................59

15 TECHNICAL SPECIFICATION...............................................................................................................................60

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 5

1FUNCTION

The 4K-8x8-L is a fully loaded 2U rack mountable 8x8 matrix switch incorporating HDBaseT technology. The

4K-8x8-L allows for the input of up to 8 HDMI 1.4, HDCP 2.2 inputs and can be switched to any combination

of the 8 available outputs, each of which has a up to 70m CATx HDBaseT output or a local HDMI output.

The 4K-8x8-L can pass 4K @60Hz (YUV 4:2:0) resolutions, allowing the distribution of UHD content of sources

at distances of up to 70m.

The 4K-8x8-L incorporates a comprehensive audio switch layer. On both the input and output side of the 4K-

8x8-L are 8x SPDIF coaxial digital audio connectors and 8x 3.5mm jack audio connectors for analogue stereo

audio. This audio layer allows the 4K-8x8-L to integrate with dedicated audio amplifiers or audio distribution

systems.

Another key feature of the 4K-8x8-L is the inclusion of the bi-directional infra-red switch. On the rear of the 4K-

8x8-L are several 3.5mm stereo jacks dedicated to infra-red functionality, some for infra-red input to the 4K-

8x8-L and some allowing output of infra-red from the 4K-8x8-L. This functionality can allow the control of

sources located locally with the 4K-8x8-L from screen locations up to 70m away with the use of the included

infra-red peripherals. Alternatively, with the use of infra-red peripherals or a dedicated control system, the user

can have control of their screens from the centralized matrix location.

The 4K-8x8-L incorporates 12V power over cable (POC), this enables the powering of the HDBaseT receivers

from the matrix location via the HDBaseT outputs over the CATx cable. The 4K-8x8-L is designed for use with

the 4K-RX725 HDBaseT Lite receiver from Smart-e.

The HDBaseT Output ports enable remote connectivity to display devices fitted with a Smart-e 4K-RX725

Receiver (or other compliant HDBaseT receiver) ≤70-meters over copper twisted pair cable. 12V power is

supplied from the matrix to the transmitter through the twisted pair cabling.

The HDMI inputs and outputs provide active-input ports, enabling the installer to connect extended cable

lengths ≤15-meters dependant on resolution.

Digital signal processing technology ensures that signals are transported without distortion and the best

quality output is transmitted to the display device. A fully featured EDID management system and HDCP 2.2

compliance ensure optimal image quality and compatibility.

The 4K-8x8-L can be controlled by a variety of methods including:

▪Remote control, via supplied infra-red handset.

▪Remote control via RS232 serial command

▪Remote control via TCP/IP Ethernet

▪Control via integrated web server

▪Front panel buttons with LCD indicator

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 6

2FEATURES

▪19-inch Rack Mountable Form Factor.

▪8x independent HDMI inputs, HDMI 1.4 HDCP 2.2

▪8x independent RJ45 HDBaseT outputs

▪8x mirrored HDMI outputs, HDMI 1.4 HDCP 2.2

▪DVI 1.0 compliant

▪Support for HD, Full HD and UHD resolutions

▪Comprehensive EDID management

▪Supports switch throughput of HDBaseT control (Infrared bi-directional)

▪HDMI HDCP 2.2 compliant

▪HDMI CEC compliant

▪External control via RS232 serial.

▪External control via TCP/IP.

▪Control via integrated web server

▪Integrated cooling fan system

▪Digital audio embedding and de-embedding

▪Analogue audio embedding and de-embedding

▪Easy to use front panel controls

▪Front panel mounted LCD system display

▪Integrated power supply

▪12V POC support

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 7

3CHASSIS PANEL DESCRIPTION

Front Panel | 4K-8x8-L

1. LCD Display 16x2 character system status display

2. IR receiver Infra-red receiver for supplied IR handset

3. System status LEDs

a. RUN LED Lit green when system processor running

b. IR LEDBlinks when IR activity received

4. Output buttons

5. Input buttons

6. System control buttons

7. Firmware upgrade port USB micro port to load firmware upgrades

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 8

Rear Panel | MDX-8x8

1. 8 x HDMI inputs

2. 8 x RJ45 and HDMI outputs

HDMI output mirrored to HDBaseT output

3. 8 x coaxial SPDIF digital audio inputs

4. 8 x 3.5mm stereo jack analogue stereo audio inputs

5. 8 x coaxial SPDIF digital audio outputs

6. 8 x 3.5mm stereo jack analogue stereo audio outputs

7. Infra-red inputs 3.5mm stereo jacks

8. Infra-red outputs 3.5mm stereo jacks

9. Control ports

a. Female D9 for RS232

b. RJ45 for TCP/IP

10. IEC power inlet 100-240V AC

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 9

4APPLICATION DIAGRAM

4K-8x8-L USER MANUAL V1.0

www.smart-e.co.uk

PAGE | 10

5REMOTE CONTROL INTERFACES

5.1 RS232 SERIAL CONTROL PORT INTERFACE

Function

FUNCTION

Not Used

RS232 send data

Not Used

RS232 receive data

Not Used

Ground Earth

Not Used

5.2 TCP/IP CONTROL PORT INTERFACE

5.2.1 TCP/IP CONNECTION VIA SWITCH

Utilise a standard CatX twisted pair patch cable between the TCP/IP control port and a network switch.

Both ends of the patch cable should be terminated to EIA/TIA 568B standard:

EIA/TIA 568B Standard Linear Order

PIN 1

PIN 2

PIN 3

PIN 4

PIN 5

PIN 6

PIN 7

PIN 8

White/Orange

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

5.2.2 TCP/IP CONNECTION DIRECT VIA CROSS-CONNECT

Utilise a “cross-connect” CatX twisted pair patch cable between the TCP/IP control port and the Ethernet

LAN port on a computer.

One end of the patch cable should be terminated to EIA/TIA 568B standard:

EIA/TIA 568B Standard Linear Order

PIN 1

PIN 2

PIN 3

PIN 4

PIN 5

PIN 6

PIN 7

PIN 8

White/Orange

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

One end of the patch cable should be terminated to EIA/TIA 568A standard:

EIA/TIA 568A Standard Linear Order

PIN 1

PIN 2

PIN 3

PIN 4

PIN 5

PIN 6

PIN 7

PIN 8

White/Green

Green

White/Orange

Blue

White/Blue

Orange

White/Brown

Brown

Inhaltsverzeichnis

Andere Smarte Matrix-Umschalter Handbücher

Smarte

Smarte S4K-8x8 Bedienungsanleitung

Smarte

Smarte MDX-8X8 Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte