Smithco V-STAR 94-201 Bedienungsanleitung

TABLE OF CONTENTS

TITLE PAGE

Service

Smithco V-Star …………………………………………………………3

Service Chart……………………………………………………………4

End Users Service Chart………………………………………………5

Engine……………………………………………………………………6

Blade Replacement…………………………………………………….7

Storage…………………………………………………………………..8

Parts

94-201& 94-401 Drawing……………..……………………………….9

94-201 & 94-401 Parts List…………….……………………………..10-12

940-128 Transaxle Drawing…………………………………………..13-14

940-128 Transaxle Parts List………………………………….………15-16

SMITHCO V-STAR

The SMITHCO V-STAR is a field developed tool designed to condition the surface of putting

greens, lawn bowling greens, and tee boxes.

The V-STAR is built of the finest and heaviest material utilized on each part to insure longevity.

The frame is fabricated out of ten gauge steel to provide weight to the machine and prevent

warping. The steering has been especially engineered for operator comfort to alleviate fatigue

during prolonged use.

Before placing the V-STAR into service it must be serviced.

Operator familiarization should be conducted before use of the V-STAR on the greens. Improper

handling of the V-STAR could cause damage to the turf. Read Operator’s Manual before using

this unit on the greens.

Each Golf Course Superintendent should plan a cutting pattern of his greens.

The V-STAR should be lubricated frequently with any grade of machine oil at all moving joints,

and the bearings that are furnished with grease fittings should be greased with any good grade

Lithium or equivalent water repellent grease. The transaxle uses 3w nondetergent oil.

Good maintenance and regular servicing will insure that longevity of your SMITHCO V-STAR.

Support is readily available from your local distributor or SMITHCO.

SERVICE CHART

Before servicing or making adjustments to the machine, stop

engine, set park brake, block wheels and remove key from ignition.

Follow all procedures and ONLY use parts prescribed by the

manufacturer. Read the engine manual before maintenance.

Daily

As Required

100 Hours

200 Hours

250 Hours

300 Hours

400 Hours

Every 500 Hours/Yearly

§Engine Oil C R R R R R

Engine for Leaks and Loose Parts C C C C C C

Air Cleaner (Paper Element) C C C C C R

== Spark Plugs R C C R

Idle Speed C C

Belts C C C

* Tire Pressure C C C C C C

Fuel Level C C

Fuel Filter R R

Battery Electrolyte Level C C C C C

Clean Battery Terminals C C

=Torque Lug Nuts C C C

Lubricate C C C C C

C = Check or Clean at specified intervals

R = Replace at specified intervals

* Tire pressure: 5 psi (0.35 bar)

=Torque tire nuts after the first 10 hours and every 200 hours there after (64 to 74 ft/lb

(87-100 NM)

§ Change oil and filter after first 5 hours.

== Gap .03 (.76 mm) Torque to 18-22 ft/lb (24-30 Nm)

Clean more often under dusty conditions or when airborne debris is present, replace air

cleaner

parts, if very dirty.

The suggested maintenance checklist is not offered as a replacement for the manufacturer’s engine

manual but as a supplement. You must adhere to the guidelines established by the manufacturer for

warranty coverage. In adverse conditions such as dirt, mud or extreme temperatures, maintenance

should be more frequent

END USER’S SERVICE CHART

Daily

As Required

100 Hours

200 Hours

250 Hours

300 Hours

400 Hours

Every 500 Hours/Yearly

§Engine Oil

Engine for Leaks and Loose Parts

Air Cleaner (Paper Element)

== Spark Plugs

Idle Speed

Belts

*TirePressure

Fuel Level

Fuel Filter

Battery Electrolyte Level

Clean Battery Terminals

=Torque Lug Nuts

Lubricate

C = Check or Clean at specified intervals

R = Replace at specified intervals

* Tire pressure: 5 psi (0.35 bar)

=Torque tire nuts after the first 10 hours and every 200 hours there after (64 to 74 ft/lb

(87-100 NM)

§ Change oil and filter after first 5 hours.

== Gap .03 (.76 mm) Torque to 18-22 ft/lb (24-30 Nm)

Clean more often under dusty conditions or when airborne debris is present, replace air

cleaner

parts, if very dirty.

ENGINE

Change and add oil according to chart below. Do not overfill. Use a high quality detergent oil.

Use no special additives with recommended oils. Do not mix oil with gasoline.

SAE VISCOSITY GRADES

Starting Temperature Range Anticipated Before Next Oil Change

NOTE: Use of multi-viscosity oils (10W-30, etc.) will result in increased oil consumption. Check

oil level more frequently if using these types of oils.

BLADE REPLACEMENT

1. Remove blade assembly from unit.

2. Once blade assembly is out, starting at the left side of the assembly remove the 2-bolt

flanged bearing and then loosen 1” nut and remove.

3. At this time, it is very important that you look at the arrangement of the blades and how

they are aligned on the shaft before removing.

4. Remove all blades and spacers from the shaft.

5. Now the new blades can be installed on shaft. Make sure that the small hole on the

blade is rotated one turn each time to rotate blade as per drawing above. Note: Make

sure the rotations of the blades are going forward with the unit.

6. After blades and spacers have been installed on the shaft and before tightening down

locknut, you should use a liquid locktite on the threads to ensure nut from backing off.

7. Place blade assembly back on unit and secure. When engaging, always test blade

alignment at very low rpm.

STORAGE

When storing, remove the key from the key switch to avoid unauthorized persons from operating

machine.

1. Before storing, clean machine thoroughly.

2. Check bolts and nuts, tighten as necessary.

3. Make all repairs that are needed and remove any debris.

4. Remove the battery, adjust the electrolyte level and recharge it. Store the battery in a

dry, dark place.

5. Store in a clean and dry area, but NOT near a stove, furnace or water heater which uses

a pilot light or any device that can create a spark.

6. Engines stored over 30 days need to be protected or drained of fuel to prevent gum from

forming in a fuel system or on essential carburetor parts. Check the engine manual and

follow the instructions for the storage of the engine.

94-201 & 94-401 V-STAR DRAWING

94-201 & 94-401 V-STAR PARTS LIST

REF# PART# DESCRIPTION QTY.

1 44-763 Parking Brake Lever 1

2 940-234 Engagement Lever Mounting Plate 1

3 44-001 Control Cable 1

4 730-220 Actuator Switch 1

5 932-071 Key Switch 1

6 720-011 Handle Grip 2

7 940-215 Handle Bar Assembly 1

8 940-130 Wiring Harness f/94-201 Vanguard 1

8 940-131 Wiring Harness f/94-401 Honda 1

9 44-715 Throttle Cable 1

11 730-052 Spacer ¾” x ½” 1

13 940-237 Caster Bracket 1

14 940-240 Shifter Handle 1

15 932-022 Seal 2

16 940-241 Shift Cable 1

17 40-168 Cotter Pin 1/8” x 1” 2

18 940-216 Actuator Mount 1

19 88-021 Clevis Pin 1/2” x 2 1/2” 2

20 400-307 Hitch Pin #16 2

21 732-117 Actuator 12V / 4” Stroke/1000# 1

22 940-204 Actuator Shaft 1

23 940-136 ½” Roll Pin 2

24 940-229 1” Spacer 2

25 940-205 Lift Arm 2

26 940-211 Connecting Arm 2

27 720-004 1” Bearing 5

28 940-135 Roll Pin 3/8” x 1 ½” 2

29 940-112 Height Adjustment Knob 1

30 940-113 Height Adjustment Lock Handle 1

31 940-112-1 Height Adjustment Bolt 1

32 940-207 Height Adjustment Arm 1

33 940-208 Height Adjustment Roller 2

34 940-206 Height Adjustment Shaft 1

35 940-213 Upright Handle Right 1

36 940-214 Upright Handle Left 1

37 940-220 Handle Bracket Right 1

38 940-221 Handle Bracket Left 1

39 940-203 Lift Assembly 1

40 940-239 Rear Axle Assembly 1

41 400-025 1” Bolt 2

42 400-203 3/8” Washer 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Smithco Landwirtschaftliche Geräte Handbücher

Smithco

Smithco 200D220 Kurzanleitung

Smithco

Smithco Spray Star 1200 Kurzanleitung

Smithco

Smithco SweepStar V62 Kurzanleitung

Smithco

Smithco TCV 5000 Kurzanleitung

Smithco

Smithco 1002 Bedienungsanleitung

Smithco

Smithco AER 8 Series Betriebsanleitung

Smithco

Smithco Spray Star 1600P Kurzanleitung

Smithco

Smithco 1008 Bedienungsanleitung

Smithco

Smithco SUPER STAR 42-000-D Bedienungsanleitung

Smithco

Smithco AER 8 Aerifier Kurzanleitung

Smithco

Smithco Super Star 42-000-E Bedienungsanleitung

Smithco

Smithco ZTR093 Kurzanleitung

Smithco

Smithco SUPER STAR 42-001-D Bedienungsanleitung

Smithco

Smithco SN FWR-001 Kurzanleitung

Smithco

Smithco Spray Star 1000 Kurzanleitung

Smithco

Smithco 300G169 Kurzanleitung

Smithco

Smithco 1010 Bedienungsanleitung

Smithco

Smithco AER60-005 Kurzanleitung

Smithco

Smithco Spray Star 2000 Kurzanleitung

Smithco

Smithco Fairway Ultra 10 Kurzanleitung

Smithco

Smithco Spray Star 1006 Bedienungsanleitung

Smithco

Smithco Super Star Bedienungsanleitung

Smithco

Smithco AER60-110 Kurzanleitung

Smithco

Smithco 1004 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung