SNAIGE MD40DD Bedienungsanleitung

MEDICAL REFRIGERATOR

Instruction for use

MD40DD

DEAR CUSTOMER!

CAREFULLY READ THE INSTRUCTION MANUAL. If instructions are not followed,

there is a risk of injury, damage of the appliance and loss of the right to free warranty

service.

The Manufacturer shall not be held liable for damage arising from the failure to

observe the instructions contained in this manual.

Keep this manual for future reference, or to pass it over to the next user.

General information:

The refrigerator is a vertical refrigerator - showcase with a glass package door

intended for non-household use. The refrigeration appliance can be used in

pharmacies or for other activities, related with storage of medicines.

The noise emitted by the refrigerator does not exceed 50 dB (A).

 The refrigerator complies with the requirements of DIN 13277.

GUIDELINES CONCERNING THE SAFETY OF USE

General safety requirements:

–WARNING: Do not cover the ventilation openings of the appliance.

–WARNING: Do not use electrical appliances inside the storage compartments

of the appliance, unless they are of the type recommended by the manufacturer.

–WARNING: Do not use any mechanical tools or other/chemical agents other

than those recommended by the manufacturer to speed up the defrosting

process.

–WARNING: When positioning the appliance, ensure the supply cord is not

trapped or damaged.

–WARNING: Do not locate multiple portable socket-outlets or portable power

supplies at the rear of the appliance.

–WARNING: Disposal of the appliance should be according to national rules.

WARNING: Do not damage the appliance refrigeration system. It contains

the refrigerant gas R600a. If the refrigeration system is damaged:

•Do not use any open flame.

•Avoid sparks - do not turn on/off any electrical appliances or lighting fixtures.

•Immediately ventilate the room: air the room in which the appliance is placed for

a few minutes (the size of the room for a product containing isobutane/ R600a

must be at least 4 m3).

C-Pentane is used as blowing agent in the insulation foam and it is a

flammable gas.

–This appliance is designed only for cooling and storing of pharmaceuticals.

–This appliance is not designed for storage of explosives, such as aerosols with

flammable gases.

–It is prohibited to store petrol and other flammable liquids near the appliance.

–Do not allow children to play with the packaging material from the appliance.

–Do not allow children to play with the appliance

–This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Requirements for the connection to the mains:

–The appliance should ONLY BE CONNECTED TO AN EARTHED SOCKET

INSTALLED IN ACCORDANCE WITH THE REGULATIONS. Make sure that the

supply voltage corresponds with the voltage marked on the rating label. This

product complies with all binding CE labelling directives. The earthed electrical

socket by which the appliance is connected to the mains should be in an

accessible place. It is a legal requirement that the appliance is properly earthed.

The manufacturer will not be held liable for any damage or injury which may

result from the failure to fulfil this requirement.

–It is mandatory to replace a damaged power cord with a proper one of the same

type as the one used by the refrigeration appliance manufacturer to prevent

damage to health an property

–To avoid the exposure to danger, always have faulty cable be replaced only by

the manufacturer, by our customer service or by a qualified person and with a

cable of the same type.

–It is forbidden to readjust or modify any parts of the unit. It is crucial not to

damage the capillary tube visible in the compressor recess. The tube may not

be bent, straightened or wound. If the capillary tube is damaged by the user the

guarantee will be void.

–Do not use adapters, multiple sockets and two-wire extension leads. If it is

necessary to use the extension lead, it must be equipped with a protection ring

and a single socket and must have a VDE/GS safety certificate. If an extension

lead is used (with a protection ring and safety certificate), its socket must be

located at a safe distance, away from the sinks, and must not be in a place where

it could be flooded by water or waste water.

–The frequency and power of the electricity supply in your house must conform

to the general data parameters of the appliance as it is shown in the product

label.

–When positioning the appliance, be careful that the electrical cord isn’t squeezed

in order to avoid damaging it. Do not store heavy objects such as cooling devices

or other devices next the appliance in such a way that they could squeeze and

damage the electrical cord. This can cause a short circuit and a fire.

–Make sure that the plug of the electrical cord is not squeezed by the back wall

of the appliance or otherwise damaged. A DAMAGED PLUG CAN BE THE

CAUSE OF A FIRE!

CAUTION! If the installed interior lighting or the advertising panel’s light-

emitting diode (LED) lamp for the cooling device is not functioning, contact

the maintenance and repair representative for replacements. LAMPS CAN

BE REPLACED ONLY BY THE MAINTENANCE AND REPAIR

REPRESENTATIVE

DO NOT TRY REPAIR THE APPLIANCE ON YOUR OWN. ALWAYS

CONTACT AN AUTHORIZED TECHNICIAN. TO AVOID THE EXPOSURE

TO DANGER, ALWAYS HAVE FAULTY CABLE BE REPLACED ONLY BY

THE MANUFACTURER, BY OUR CUSTOMER SERVICE OR BY

QUALIFIED PERSON WHIT A CABLE OF SAME TYPE.

Requirements for safe use:

–It is forbidden to use a technically damaged appliance.

–If the appliance is unplugged (for cleaning, moving to another place, etc.), it may

be repeatedly switched on after 15 min.

–When performing activities, such as cleaning, maintenance or moving, the

appliance must be completely disconnected from power supply (by pulling the plug

out from the socket). Do not pull on the cord, but hold the body of the plug

instead.

–Do not place heavy objects on the top of the refrigerating appliance.

–Do not place any switched on electrical devices on top of the appliance because

this may cause ignition of plastic parts.

–Do not place any dishes with liquids on top of the appliance and do not keep

flowers in vases or other liquid-filled vessels on the appliance.

–Do not climb on or sit on the appliance, do not lean on or hang on the appliance

doors and do not allow children to do this.

–Do not use water spray and steam to clean the appliance.

The appliance should be transported in the vertical position; do not tilt any

more than 30°. THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR ANY

DAMAGE OF THE APPLIANCE THAT RESULTS FROM NON-COMPLIANCE WITH THE

INSTRUCTIONS FOR TRANSPORTATION.

INSTALLATION AND OPERATING CONDITIONS

Positioning:

•This appliance can be installed in a dry, well ventilated indoor location where the

ambient temperature corresponds to the climate class indicated on the rating plate of

the appliance.

CAUTION! Do not install this appliance in areas that are too humid or too cold.

Place the appliance away from heat sources such as kitchen stove/oven,

radiators, or direct sunlight. The appliance must not touch any pipes for heating,

gas or water supply, or any other electrical devices.

•Do not cover the ventilation holes at the top of the appliances –it must be a good air

circulation around the appliance. There should be a gap of at least 10 cm between the

top of the appliance body and any furniture that may be above it. If this requirement is

not followed, the appliance consumes more electrical energy and its compressor may

overheat.

•The appliance must stand on a level surface

and must not touch the wall. If necessary,

regulate the height of the appliance by

adjusting the levelling feet: by turning them

clockwise –the front of the appliance rises, by

turning them counter clockwise –it comes

down. If the appliance is tilted slightly

backward –the doors will close by themselves.

•If the appliance is placed in a corner, a gap of

at least 5 cm must be left between the

appliance body and the wall.

Preparing for operation:

•It is recommended to prepare the appliance for operation with a helper.

•Remove package. Lift the appliance away from foamed polystyrene base. Therefore

take out adhesive tapes from sides and simply lift the appliance up and take out the

board. Strip adhesive tapes off and open the door. Remove all the red coloured parts,

they are only used for the transportation of the appliance.

•When positioning the appliance in chosen location, it will move more easily into position

if you lift the front a little and incline it backward allowing it to roll on its casters.

•When placing, moving, lifting the appliance, do not hold the door handles, do

not pull the condenser at the rear part of the refrigerator and do not touch

the compressor unit.

•When installing the refrigerator, do not tilt it more than 30 ° to the intended

location.

•When placing the refrigerator in the intended place, turn the front part slightly

backwards - you can easily place the roller on the castors in the desired place.

•The appliance should not be connected to the mains until all packing and

transport materials are removed. Suitably dispose the packaging material.

First use:

•Before using the appliance for the first time, the interior and all internal accessories

should be washed with lukewarm water and some neutral soap to remove the typical

smell of a brand-new product, then dried thoroughly.

•Once the unit has been positioned, wait for about 30 minutes before it is connected

to the mains.

After connecting the refrigerator to the mains, switch on the

emergency backup power supply to the controller using switch 11

(Fig.1)

When the refrigerator is decommissioned and disconnected

from the mains, it is necessary to disconnect the emergency

backup power supply to the controller using switch 11 (Fig.1)

If the unit has been tilted more than 30° during transport: Wait at least

4 hours before connecting the appliance to the power supply. If this is

not done, the appliance compressor may fail.

The products can be placed in the refrigerator when its internal temperature

reaches + 5 ° C.

DESCRIPTION OF THE APPLIANCE, BASIC PARTS



Electronic control panel with

buttons

Condenser

Door opening switch

Compressor

Advertising panel

Tray for collection of the defrost

water

Interior lighting unit

Emergency power disconnect switch

Fan

External alarm connection

Shelves

RS485 network connection

Security controller

When the appliance is switched on, the fan starts and works together with the

compressor.

When the door is opened, the fan switches off and the interior lighting of the refrigerator

turns on. If necessary, the interior lighting can be switched on for permanent lighting.

The refrigerator has a second safety controller that prevents the

temperature in the refrigerator from falling below + 2 °C.

NOTE. The technical data of the appliance can be found on the rating label attached to

the inside wall of the appliance. For more information about the appliance, scan the QR

code on the enclosed energy label and / or visit the official website of the product

database: https://eprel.ec.europa.eu

DESCRIPTION OF THE ELECTRONIC CONTROLLER

TEMPERATURE ADJUSTMENT

Electronic controller has the following functions:

1. Temperature recording and alarm recording functions;

2. Transfer of saved data to a USB storage device (USB storage device is supplied

with the refrigerator);

3. Emergency 12 hour power supply and alarm function;

4. Setting the maximum allowable temperature limit;

5. Setting the minimum allowable temperature;

6. Possibility to connect an external alarm system;

7. Possibility to connect to external temperature and other parameters monitoring

system XWEB (purchased separately);

„SET“ to display target set point; in programming mode it selects a

parameter or confirm an operation

„UP“ to enter fast access menu; In programming mode, scroll through

parameter codes or increase the displayed value.

„DOWN“ in programming mode it browses the parameter codes or

decreases the displayed value.

„DATA“ exporting data to a USB storage device

„LiG“ to switch the light

„REC“ the data logging inside the controller is factory activated.

Shutdown (password protected), contact service.

Controller LED functions and description

LED

Mode

Function

Compressor enabled

Flashing

Anti-short cycle delay enabled

Defrost enabled

Flashing

Drip time in progress

Fan enabled

Flashing

Fans delay after defrost in progress

There are alarm logs

Recording activated

Battery status OK

Flashing

Charging problem or battery failure

Measurement unit

Flashing

Programming phase

When the appliance is connected to the mains for the first time, the electronic controller

will display the current temperature inside the appliance (hereinafter referred to as the

ACTUAL temperature).

When connected to the mains, switch on the emergency backup power supply to the

controller using switch 11 (Fig.1) on the back of the refrigerator. The symbol

lights up on the controller display.

With the help of emergency backup power only the controller, that

registers the temperature change in the refrigerator, operates. All the

other electrical components of the refrigerator (compressor, fan,

lighting) do not work.

Set the date and time settings, disable the real-time menu (the RTC) alarm.

BEGIN

1. Enter the Programming Mode pressing both

„SET+DOWN“keys for 3sec.

2. Use the UP or „DOWN“button till the „CLO“menu

is displayed

Display

Press SET to enter the settings menu

Display

1. HUr =hour → press „SET“to modify/confirm. „UP/DOWN“–to

modify the parameter.

2. Min =minutes → press „SET“to modify/confirm. „UP/DOWN“–to

modify the parameter.

3. dAy =Day of the month → press „SET“to modify/confirm.

„UP/DOWN“–to modify the parameter.

4. Udy =Day of the week → (Sun, Mon, Tue, Ued,thE, Fri, Sat) press

„SET“to modify/confirm. „UP/DOWN“–to modify the parameter.

5. Mon =month → press „SET“to modify/confirm. „UP/DOWN“–to

modify the parameter.

6. yEA =year →press „SET“to modify/confirm. UP/DOWN –to modify

the parameter.

EXIT

Press both SET and UP together The audible alarm is

switched off at the same time. Exiting the menu takes

place automatically without activating any button for

about 10s

The refrigerator is unadjustable and the appliance is set at a

temperature of +5 °C at the factory.

The set temperature can be changed by the manufacturer or SNAIGĖ SERVISAS official

representatives.

Electronic controller will always display the actual temperature in the

refrigeration unit instead of the set temperature.

NOTE. The electronic controller on the display shows the variable air temperature near

the evaporator and is used to control the refrigeration unit. I.e. the controller displays the

actual average temperature, so when storing products that are sensitive to

temperature changes, it is recommended to use additional temperature measuring

devices (positioned at different device heights) for optimal temperature selection.

Temperature recording and data transfer to a USB key

To export log data to a USB key, follow these steps:

1. Insert the supplied product-specific USB storage media that comes with the

refrigerator;

2. Press the „DATA“ button until "dat" appears;

3. The controller starts transferring data to the USB key;

4. The message "Lod" will be displayed on the screen during data export, and then

a message „Alr“;

5. When the data transfer is complete, the following message will be displayed:

–„End“ if everything's okay

–„Err“ if the data transfer failed.

The controller keeps the logs last:

a) 100 alarm entries along with the date and duration of the event „ALARM.txt“

b) A summary of temperature measurement records along with the date and time

of the recording „DATA.txt.“

CLEANING AND CARE

THE REFRIGERATING APPLIANCE DEFROSTS AUTOMATICALLY. Drops of ice that form

on the back wall of the refrigerator compartment thaw during the time the compressor is

not working. Indication appears on the screen of electronic controller. Thaw water runs

down the thaw water runoff channel to the tray on top of the compressor, where it

evaporates. CLEAN THE APPLIANCE.

Warning: Be sure to unplug the battery before cleaning using the

on / off button on the back of the refrigerator and unplug it

from the electrical outlet.

Inhaltsverzeichnis

Andere SNAIGE Kühlschrank Handbücher

SNAIGE

SNAIGE CD40DM Bedienungsanleitung

SNAIGE

SNAIGE CC70MF Bedienungsanleitung

SNAIGE

SNAIGE MD14DC Bedienungsanleitung

SNAIGE

SNAIGE R 13SM Bedienungsanleitung

SNAIGE

SNAIGE R 13SM Bedienungsanleitung

SNAIGE

SNAIGE RF53SG Bedienungsanleitung

SNAIGE

SNAIGE CD290-1004 Bedienungsanleitung

SNAIGE

SNAIGE CD29DM Bedienungsanleitung

SNAIGE

SNAIGE C 29SM Bedienungsanleitung

SNAIGE

SNAIGE R 130 Bedienungsanleitung

SNAIGE

SNAIGE WD35SM Bedienungsanleitung

SNAIGE

SNAIGE RF31SM Bedienungsanleitung

SNAIGE

SNAIGE SGM020P2AA Series Handbuch

SNAIGE

SNAIGE Fresh INN RF53SM Bedienungsanleitung

SNAIGE

SNAIGE C 14SM Bedienungsanleitung

SNAIGE

SNAIGE RF27SM Bedienungsanleitung

SNAIGE

SNAIGE FR27SM Bedienungsanleitung

SNAIGE

SNAIGE MD40DC Bedienungsanleitung

SNAIGE

SNAIGE FR240 Bedienungsanleitung

SNAIGE

SNAIGE CD48DM-S300BD Bedienungsanleitung

SNAIGE

SNAIGE C 31SM Bedienungsanleitung

SNAIGE

SNAIGE RF62FB-TNCBNE0 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung