SNBC BTP-L580IIC Bedienungsanleitung

USER’S MANUAL

Label Printer

BTP- L580IIC

Shandong New Beiyang Information Technology Co., Ltd

BTP-L580IIC User’s Manual

- 1 -

Declaration

Information in this document is subject to change without notice. SHANDONG NEW BEIYANG

INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the

right to improve products as new technology, components, software, and hardware become

available. If users need further data about these products, please feel free to contact SNBC or

your local dealer.

No part of this document may be reproduced or transmitted in any form or by any means for

any purpose without the express written permission of SNBC.

Printed in China

Version 1.0

Trademark

Registered trademark of SNBC:

Warning and caution

Warning: Items shall be strictly followed to avoid injury or damage to body and equipment.

Caution: Items with important information and prompts for operating the printer.

SNBC has been approved by the following certifications:

ISO9001 Quality Control System

ISO14001 Environmental Management System

OHSAS18001 Occupational Health and Safety Management System

IECQ QC080000 Hazardous Substance Process Management System

BTP-L580IIC has been approved by the following certifications of

environmental protection:

BTP-L580IIC User’s Manual

- 2 -

Safety instructions

Before installing and using the printer, please read the following items carefully:

1．

Safety warning

Warning Do not touch the cutter of the printer.

Warning The print head is a thermal element and it is at a high temperature during

printing or just after operation, therefore do not touch it or its peripherals for

reasons of safety.

Warning The print head is an ESD-sensitive device. To avoid damage, do not touch

either its printing parts or connecting parts.

2．

Cautions

1) Install the printer on a flat and stable surface;

2) Reserve adequate space around the printer so that convenient operation and

maintenance can be performed;

3) Keep the printer far away from water source, and do not expose the printer to direct

sunlight, strong light and heat;

4) Do not use or store the printer in a place exposed to high temperature, high humidity or

serious pollution;

5) Do not place the printer in a place exposed to vibration or impact;

6) No condensation is allowed to the printer. In case of such condensation, do not turn on

the power until it has completely gone away;

7) Connect the printer power to an appropriate grounding outlet. Avoid sharing one electrical

outlet with large power motors or other devices that may cause the fluctuation of voltage;

8) Disconnect the power when the printer is deemed to idle for a long time;

9) Don’t spill water or other electric materials into the printer (e.g. metal). In case this

happens, turn off the power immediately;

10) Do not allow the printer to start printing when there is no recording paper installed;

otherwise the print head and platen roller will be damaged;

11) To ensure quality print and normal lifetime, use recommended paper or its equivalent;

12) Shut down the printer when connecting or disconnecting interfaces to avoid damages to

control board;

13) Set the print darkness to a lower grade as long as the print quality is acceptable. This will

help to keep the print head durable;

14) Do not disassemble the printer without permission of a technician, even for repairing

purpose;

15) Keep this manual safe and at hand for reference purpose.

BTP-L580IIC User’s Manual

- 3 -

Contents

1 Overview......................................................................................................................-1-

1.1 Introduction............................................................................................................ - 1 -

1.2 Main features......................................................................................................... - 1 -

2 Specifications............................................................................................................... - 2 -

2.1 Technical specifications.......................................................................................... - 2 -

2.2 Cutter specifications .............................................................................................. - 3 -

2.3 Paper specifications............................................................................................... - 3 -

2.3.1 Parameters of label paper................................................................................ - 3 -

2.3.2 Parameters of thermal continuous paper .......................................................... - 4 -

2.3.3 Parameters of marked paper............................................................................ - 4 -

2.4 Print and tear-off position ....................................................................................... - 5 -

2.4.1 Print position ................................................................................................... - 5 -

2.4.2 Tear-off position............................................................................................... - 5 -

3 Appearance and modules ............................................................................................. - 6 -

3.1 Appearance and modules....................................................................................... - 6 -

3.2 LED & buzzer......................................................................................................... - 7 -

4 Printer installation ........................................................................................................ - 8 -

4.1 Unpacking.............................................................................................................. - 8 -

4.2 Printer installation .................................................................................................. - 8 -

4.3 Power connection .................................................................................................. - 8 -

4.4 Connect interface cable ......................................................................................... - 9 -

4.5 Connect USB cable................................................................................................ - 9 -

4.6 Connect cash drawer cable .................................................................................... - 9 -

4.7 Install paper roll ................................................................................................... - 10 -

4.7.1 Confirm paper type ........................................................................................ - 10 -

4.7.2 Install/replace paper roll ................................................................................ - 10 -

4.8 Paper near end position adjustment ......................................................................- 11 -

4.9 Power-on and self-test ..........................................................................................- 11 -

4.9.1 Power on the printer .......................................................................................- 11 -

BTP-L580IIC User’s Manual

- 4 -

4.9.2 Print self-test page .........................................................................................- 11 -

4.10 Guide for hexadecimal dumping mode .................................................................. - 12 -

4.10.1 Hexadecimal dumping function ...................................................................... - 12 -

4.10.2 Running hexadecimal dumping ...................................................................... - 12 -

5 Routine maintenance.................................................................................................. - 13 -

5.1 Clean print head and platen roller......................................................................... - 13 -

5.2 Clean sensors...................................................................................................... - 13 -

5.3 Clear paper jam ................................................................................................... - 13 -

5.4 Guide for updating printer firmware via U-Disk...................................................... - 13 -

6 Interface signal .......................................................................................................... - 15 -

6.1 Parallel interface.................................................................................................. - 15 -

6.2 Serial interface .................................................................................................... - 16 -

6.3 USB interface ...................................................................................................... - 16 -

6.4 Ethernet interface ................................................................................................ - 16 -

6.5 WLAN interface.................................................................................................... - 17 -

6.6 Power interface definition..................................................................................... - 18 -

6.7 Signal definition of cash drawer interface ............................................................. - 18 -

7 Troubleshooting ......................................................................................................... - 19 -

7.1 Printer doesn’t work ............................................................................................. - 19 -

7.2 ERROR LED and buzzer alarm ............................................................................ - 19 -

7.3 Problems during printing ...................................................................................... - 19 -

8 Options ...................................................................................................................... - 20 -

8.1 Kitchen printing prompt device ............................................................................. - 20 -

9 Power management.................................................................................................... - 21 -

Appendix: Button configuration menu ................................................................................ - 22 -

BTP-L580IIC User’s Manual

- 1 -

1 Overview

1.1 Introduction

BTP-L580IIC is a high performance thermal printer, which can be widely used for real-time

printing applications, such as retail, warehousing, logistics, medicine, etc.

BTP-L580IIC can be connected with other devices via parallel, serial, USB, Ethernet or WLAN

interface, it can provide drivers and label software for operating systems such as WINDOWS

2000/XP/Server2003/VISTA/ Server2008/WIN7, Linux, and MAC.

1.2 Main features

¾Low noise, high print speed;

¾Easy paper loading;

¾Easy use and maintenance;

¾Thermal label paper, thermal marked paper and thermal continuous paper are available;

¾Compatible with various paper width between 54.5～82.5mm;

¾Cutting paper automatically;

¾Cash drawer control interface;

¾Communication interface optional;

¾ESC/POS compatible;

¾Function of saving paper;

¾Low power consumption design (Min. power consumption is about 1W): the default waiting

time of entering sleep mode is 5 minutes.

BTP-L580IIC User’s Manual

- 2 -

2 Specifications

2.1 Technical specifications

Item Parameter

Print method Direct thermal line

Print resolution 203×203DPI

Print speed 150mm/s for thermal label paper, 230mm/s for thermal continuous

paper

Print width Max. 80mm

Paper type Thermal label paper, thermal marked paper and thermal continuous

paper

Barcode type

One-dimensional barcode: UPC-A, UPC-E, EAN-8, EAN-13 , Codabar,

Code39, Code128, Code93, ITF

Two-dimensional barcode: PDF417, QR, Maxicode

GS1 barcode

Character

Font A: 12×24

Font B: 9×17

Kanji Font A: 24×24

Optional: Simplified Chinese, Korean, Traditional Chinese, Japanese,

English

Codepage: 57 kinds of codepages

International character sets: 14 kinds

Character enlargement All characters can be enlarged 1-6 times horizontally and vertically.

Character rotation Rotation printing in four directions (0°, 90°, 180°, 270°)

Paper near end detection Photoelectric sensor

Paper end detection Photoelectric sensor

Paper existence

detection Photoelectric sensor

Top cover position

detection Micro switch

Print head temperature

detection Thermal resistor

Bitmap download Direct bitmap printing

Image processing Download buffer size:

RAM: 128KB

FLASH: 512KB

Support bitmap print mode and realize

fast image printing.

Communication interface

USB interface(Fixed on board)

Standard parallel interface or RS232 serial interface, RS485 interface,

Ethernet interface, WLAN interface (optional)

Cash drawer interface Can control 2 cash drawers.

Memory RAM: 2MB

FLASH: 2 MB /4MB

Power supply 110-240VAC, 50/60Hz

Print head lifetime ≥1,000,000 labels (standard test sample with 12.5% duty ratio)

Operating temperature

and humidity 5～45℃, 20%～90% (40°C)

Storage temperature and

humidity -40～60℃, 20%～93% (40℃)

External dimensions 155.5 (W) ×205 (D) ×160 (H) mm

BTP-L580IIC User’s Manual

- 3 -

2.2 Cutter specifications

Item Parameter Remarks

Cutting mode Sliding blade

Cutting time 600ms The time that one cut takes

Cutting interval 2s 30 cuts/min (Max.)

Applicable

paper type 0.06～0.1mm Thermal paper or paper with the same thickness

Operating

voltage 24VDC

Max. operating

current 1.2A 24VDC

Cutter lifetime Only liner paper:

1,500,000 cuts

The cutter should cut only the liner and not cut the liner together with

the label paper, otherwise it will negatively affect the lifetime of the

cutter

2.3 Paper specifications

2.3.1 Parameters of label paper

¾Paper type: thermal label paper

¾Paper supply mode: paper roll

¾Thermal layer: outward

¾Paper reflectivity:

Label: reflectivity＜18%; base paper: reflectivity＞47%

¾Paper width: 54.5±0.5 mm~82.5±0.5 mm

¾Backing paper thickness: 0.041mm-0.071mm

¾Thermal paper (label) thickness: 0.070mm-0.092mm

¾Thermal paper (label) length: 35mm-300mm

¾Thermal paper (label) spacing: 3mm-10mm

¾Paper roll OD (Max): ф100 mm

BTP-L580IIC User’s Manual

- 4 -

2.3.2 Parameters of thermal continuous paper

¾Paper type: Thermal continuous paper

¾Paper supply method: Paper roll

¾Paper width: 54.5±0.5 mm~82.5±0.5 mm

¾Paper thickness: 0.06mm-0.1mm

¾Thermal layer: Outward

¾Paper roll specifications: OD(MAX): ф100 mm

¾Recommended paper:

Paper model Manufacturer

F240AC,F220-VP,FV230A1

PA220AG,HP220A Mitsubishi Paper Mill CO., LTD

FD210,PD150R,PD160R OJI Paper CO., LTD.

F70NA FUJI PHOTO FILM CO., LTD

2.3.3 Parameters of marked paper

BTP-L580IIC can support marked paper printing and set the cutting and initial printing position

accurately. Marked paper not only should meet the parameters of thermal paper roll, but also

should meet the following requirements:

L1 mark height: 3mm≤L1≤13mm

L2 mark length: L2≥12mm

L3 mark spacing: 20mm≤L3<500mm

Mark position: The mark can be set on the left, middle or right, and when it is on the left or

right, only 80mm paper is available.

Reflectivity: The reflectivity of the marked part must be no more than 15% while the reflectivity

of the rest part should be higher than 85%. There should be no patterns like advertisement or

poster between two marks.

Caution:

To ensure quality print and normal lifetime, use recommended paper or its equivalent;

Paper cannot be stuck on the paper roll core;

If the paper is contaminated by chemical substances or grease, the contaminated part

may fade or be printed unclearly;

BTP-L580IIC User’s Manual

- 5 -

To ensure print effect, do not let hard objects scratch the thermal layer;

When the temperature exceeds 70°C, the thermal layer will fade. Thus, do not use or

store the paper in a place exposed to high temperature, high humidity, strong light, etc.;

The mark is measured when printing or feeding paper. If the sensor detects the mark is

higher than the default setting (default setting is 13mm), the printer will enter paper end

error status.

2.4 Print and tear-off position

2.4.1 Print position

L1 paper cabinet width: 83.5+0/-0.5mm

L2 effective print width: 80mm

L3 distance from print head to left edge of paper cabinet (fixed width): 1.75±1mm

L4 distance from print head to right edge of paper cabinet (fixed width): 1.75±1mm

L5 left margin: The default value is 8mm.

L6 width of print area: Set by command (refer to Programming Manual), default value: 64mm

L7 right margin: The default value is 8mm.

2.4.2 Tear-off position

L1: about 30mm

L2: about 13mm

Inhaltsverzeichnis

Andere SNBC Drucker Handbücher

SNBC

SNBC BTP-R880NP Bedienungsanleitung

SNBC

SNBC BTP-M300 Bedienungsanleitung

SNBC

SNBC BTP-R681 Bedienungsanleitung

SNBC

SNBC BTP-R880NPI Bedienungsanleitung

SNBC

SNBC BTP-2002NP Bedienungsanleitung

SNBC

SNBC BT-UC156 Bedienungsanleitung

SNBC

SNBC BK-S216 Bedienungsanleitung

SNBC

SNBC BTP-P33 Bedienungsanleitung

SNBC

SNBC BTP-P36 Bedienungsanleitung

SNBC

SNBC BK-T6112 Bedienungsanleitung

SNBC

SNBC BT-T080R Bedienungsanleitung

SNBC

SNBC BT-T080 Betriebsanleitung

SNBC

SNBC BTP-R180II Bedienungsanleitung

SNBC

SNBC KIOSK Series Bedienungsanleitung

SNBC

SNBC BTP-R880NP Betriebsanleitung

SNBC

SNBC BTP-2002NP Bedienungsanleitung

SNBC

SNBC BTP-M300 Betriebsanleitung

SNBC

SNBC BT-UC056III Bedienungsanleitung

SNBC

SNBC BTP-R580II Betriebsanleitung

SNBC

SNBC BTP-M280 Bedienungsanleitung

SNBC

SNBC BTP-R580 Bedienungsanleitung

SNBC

SNBC BTP-R180II Betriebsanleitung

SNBC

SNBC BTP-R180II Bedienungsanleitung

SNBC

SNBC BTP-R990 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung