SNBC BTP-R180II Bedienungsanleitung

USER’S MANUAL

Receipt Printer

BTP-R180II

Shandong New Beiyang Information Technology Co., Ltd

BTP-R180II User’s Manual

- 1 -

Declaration

Information in this document is subject to change without notice. SHANDONG NEW BEIYANG

INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the right to

improve products as new technology, components, software, and firmware become available. If users need

further data about this product or have any doubt about safety issues that might arise from using it, please

feel free to contact SNBC or your local agents.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or

mechanical, for any purpose without the express written permission of SNBC.

Printed in China

Version 1.0

Trademarks

Our registered trademarks are

Warnings and Cautions

Warning: Items shall be strictly followed to avoid damages to body and equipment.

Caution: Items with important information and prompts for operating the printer.

Certifications

The control system of SNBC has been approved of the following certifications:

ISO9001 quality control system certification

ISO14001 environmental control system certification

OHSAS18001 occupational health and safety control system certification

IECQ QC080000 hazardous substance process control system certification

Technical Contact Information

Address: No.169 Huoju Road High-tech Zone, Weihai, China

Hot line: 400-618-1368 800-860-1368

Fax: +86-631-5656098

PC: 264209

Website: www.newbeiyang.com.cn

BTP-R180II User’s Manual

- 2 -

General Safety Information

Before installing and using the printer, please read the following items carefully.

1. Safety instructions

Don’t touch the tear bar of printer.

The print head is a thermal element and it is at high temperature during printing or just after

operation, therefore please do not touch it and its peripherals for safety reasons.

The thermal head is an ESD-sensitive device. To prevent damage, do not touch either its printing

part or connecting parts.

2. Caution

1) Install the printer on a flat and stable place.

2) Reserve adequate space around the printer so that convenient operation and maintenance can be

performed.

3) Keep the printer away from water source.

4) Do not use or store the printer in a place exposed to heat of fire, moisture, serious pollution and direct

sunlight.

5) Do not place the printer on a place exposed to vibration or impact.

6) No dew condensation is allowed to the printer. In case of such condensation, do not turn on the power

until it has completely evaporated.

7) Connect theDC adapter to an appropriate grounding outlet. Avoid sharing a single electrical with large

power motors and other devices that may cause the fluctuation in voltage.

8) Disconnect the DC adapter when the printer is not used for a long time.

9) Don’t spill water or other materials on the printer. If this happens, turn off the power immediately.

10) Do not allow the printer to start printing when there is no recording paper installed, otherwise the print

head and platen roller will be damaged.

11) To ensure quality print and normal lifetime, use recommended or good quality paper.

12) Shut down the printer when connecting or disconnecting interfaces connectors to avoid damage to the

control board.

13) Set the print darkness to a lower grade as long as the print quality is acceptable. This will help to keep

the print head durable.

14) The printer should only be disassembled or repaired by a technician, who is certified by the

manufacturer.

15) Keep this manual safe and at hand for ready reference.

16) The following content about cutter only applies to printers with cutter.

BTP-R180II User’s Manual

- 3 -

Contents

1 Introduction................................................................................................................................................- 1 -

1.1 Outline.................................................................................................................................................- 1-

1.2 Features..............................................................................................................................................- 1-

2 Specifications.............................................................................................................................................- 2 -

2.1 Main specification...............................................................................................................................- 2-

2.2 Cutter Specification.............................................................................................................................- 3-

2.3 Paper Specification.............................................................................................................................- 3-

2.3.1 Continuous paper.........................................................................................................................- 3 -

2.3.2 Mark paper...................................................................................................................................- 4 -

2.4 Print and tear off position....................................................................................................................- 5-

2.4.1 Print position.................................................................................................................................- 5 -

2.4.2Tear off position............................................................................................................................- 5 -

3 Outline and components...........................................................................................................................- 6 -

3.1 Outline and Parts................................................................................................................................- 6-

3.2 Error LED and Buzzers.......................................................................................................................- 7-

3.2.1 Error LED .....................................................................................................................................- 7 -

3.2.2 Description of LED and Error Status...........................................................................................- 7 -

4 Installation..................................................................................................................................................- 8 -

4.1 Unpacking...........................................................................................................................................- 8-

4.2 Printer installation...............................................................................................................................- 8-

4.3 Connecting the Power Adapter ..........................................................................................................- 8-

4.4 Connecting interface cable.................................................................................................................- 9-

4.5 Connecting the Cash Drawer.............................................................................................................- 9-

4.6 Paper roll loading................................................................................................................................- 9-

4.6.1 Confirm thepaper type................................................................................................................- 9 -

4.6.2 Load/replace a paper roll.............................................................................................................- 9 -

4.7 Paper near end adjustment..............................................................................................................- 10 -

4.7.1 Paper near end position adjustment .........................................................................................- 10 -

4.7.2 Remaining paper amount adjustment of Paper near end sensor ............................................- 11 -

4.8 Power on printer and print self-test page......................................................................................... - 11 -

BTP-R180II User’s Manual

- 4 -

4.8.1 Power on printer.........................................................................................................................- 11 -

4.8.2 Print self-test page.....................................................................................................................- 11 -

5 Printer maintenance................................................................................................................................- 12 -

5.1 Print head and roller cleaning ..........................................................................................................- 12 -

5.2 Mark sensor cleaning.......................................................................................................................- 12 -

5.3 Clear paper jam ................................................................................................................................- 12 -

6 Interface Signal........................................................................................................................................- 14 -

6.1 Parallel interface...............................................................................................................................- 14 -

6.2 RS-232 serial interface.....................................................................................................................- 15 -

6.3 USB interface....................................................................................................................................- 15 -

6.4 Ethernet interface .............................................................................................................................- 15 -

6.5 Power interface definition.................................................................................................................- 16 -

6.6 Cashdrawer interface signal definition.............................................................................................- 16 -

7 Troubleshooting.......................................................................................................................................- 18 -

7.1 Printer doesn’t work..........................................................................................................................- 18 -

7.2 Error LED and Buzzer......................................................................................................................- 18 -

7.3 Problems during printing...................................................................................................................- 18 -

8 Accessories..............................................................................................................................................- 19 -

8.1 Spill proof cover ................................................................................................................................- 19 -

8.2 HERALD –kitchen alarm system.....................................................................................................- 19 -

8.3 Power Supply CASE.........................................................................................................................- 19 -

8.4 Wall Mounting...................................................................................................................................- 20 -

9 Power Management ................................................................................................................................- 22 -

BTP-R180II User’s Manual

- 1 -

1 Introduction

1.1 Outline

BTP-R180II is a high performance thermal printer, which can be widely used for real-time printing

application, such as POS system, restaurant system, ATM, etc.

BTP-R180II can be connected with other devices via parallel interface, serial interface, USB, Ethernet and

is available for WINDOWS 2000/XP/Server 2003/VISTA/WIN7/WIN8/Server2008 and Linux.

1.2 Features

◇Low noise, high printing speed

◇Easy paper loading

◇Easy use and maintenance

◇Marked paper and continuous paper available

◇Compatible with various wide paper

◇Cutting paper automatically

◇Cash drawer control connector

◇ESC/POS compatible

◇Built-in Internal Buzzer

◇Save paper function

◇Low consumption design(Min. lower than 1W)

BTP-R180II User’s Manual

- 2 -

2 Specifications

2.1 Main specification

Item

Specification

Color

Black or Ivory

Printing

Print Method

Direct Thermal

Resolution

180 ×180 DPI(standard)

Paper width

57.5/69.5/76/80/82.5mm

Print width

Max. 72mm

Print speed

Standard: Max 200mm/s

Flash capability

2M / 4M (selectable, according to different font library)

Flash LOGO

Max. 512K bytes

Data buffer

64K bytes，4K bytes，45 bytes

Interface

Serial (RS-232, Fix on board)

USB2.0(Full Speed, Fix on board)

Ethernet(Fix on board)

Parallel(IEEE1284)

Printer Status Detection

Top cover position, Paper end, Print head overheating, Print voltage,

Paper near end，Marked detection，Cutter error

Barcode

1D:UPC-A,UPC-E ,JAN8 (EAN8),JAN13 (EAN13), CODE 39,CODE

93,CODE 128, ITF,CODABAR

2D: PDF417,QR,MaxiCode

GS1

DataBar

Fonts Type

Font A 12×24,Font B 9 ×17 ,kanji 24 ×24,

Characters

95 Alphanumeric,

13 types International characters

Traditional/Simplified Chinese, Japanese, Korean (optional)

Command Emulation Supported

ESC/POS™

Paper

Paper type

Continuous paper, Marked paper

Paper OD

Max 83mm

Paper thickness

0.06mm~0.08mm

Power

Supply

Input

100-240VAC, 50-60Hz

Output

24V ±5%V DC, 1.5A

External Only

Power Adaptor

EMC and Safety Standards

CCC、CE、CB、FCC、UL

Human-

Machine

Interface

Power switch

Micro switch

Button

FEED button

LED

POWER LED, ERROR LED

Buzzer

Built-in buzzer

Reliability

Lifetime of print head

150 km(standard test condition)

Lifetime of cutter

1,500,000 cuts(standard test condition)

MCBF

60,000,000 lines

MTBF

360,000 hours

BTP-R180II User’s Manual

- 3 -

Operation condition

5°C to 45°C, 20% to 90%RH (40°C)

Storage condition

-40°C to 60°C, 20% to 93%RH (40°C)

Dimension

195 L x 145 W x 141 H (mm)

Weight

Approx 1.45Kg

Functions

Cash drawer

2 drives

Feed button config

Support(config the printer without computer)

Bi-colour printing

Support

Right-up-side

Support

Water mark

Support

Optional Accessories

Spill proof Cover, Herald, Power Adapter Cover

Driver

Win2000(32), WinServer2003(32&64), WinServer2008(32&64),

WinXP(32&64), WinVISTA(32&64), Win7(32&64),Win8(32&64),

Linux CUPS,

OPOS, JavaPOS

Software

Printer Utility(include EEPROMset, LOGO download, customized

codepage)

2.2 Cutter Specification

Item

Parameter

Note

Cutter type

Slide cutter

Cutting time

500ms

The time that one cut takes

Cutting interval

20 times/min. (Max.)

Paper type

0.06～0.08mm

Thermal paper or paper with the same

thickness

Operation voltage

24VDC

Max. dynamic current

1.5A

24VDC

Cutter lifetime

1500,000 cuts (reference

paper with thickness of 0.06

mm)

Full or partial cuts

Full cut: Cut off the paper completely

Partial cut: 2 mm paper left in middle

2.3 Paper Specification

2.3.1 Continuous paper

Paper type: Continuous thermal paper

Paper supply method: Paper roll

Paper width: 82.5±0.5mm,80±0.5mm, 76±0.5 mm,69.5±0.5mm 57±0.5mm

Paper thickness: 0.06mm-0.08mm

Thermal senstive layer: Outside

Paper roll specifications OD(MAX):ф83mm

Recommended reference paper:

Paper type

Manufacturer

TF50KS-E2C,TF50KS-E

Nippon Paper Industries Co., Ltd.

F70NA

FUJI PHOTO FILM Co., Ltd.

F240AC/F220-VP,

Mitsubishi Paper Mill Co., Ltd.

BTP-R180II User’s Manual

- 4 -

FV230A1,PA220AG,

HP220A

PD150R, PD160R

OJI Paper Co., Ltd.

F5041, F5051, P5045,

P5055

Mitsubishi HitTec Paper Flensburg

GmbH

KF50, KP440

Kanzan Spezialpapiere GmbH

KT55F20, KT58F20, KT55HS

Papier-fabrik August Koehler AG

P300, P350, P530

Kanzaki Specialty Paper

Caution:

Please use the recommended reference paper type or its equivalents. Using the lower quality paper

types might affect the print quality and shorten print-head life.

If the paper is contaminated by chemical or oil, it may discolor or lose heat sensitivity at the polluted

spot.

Do not rub the paper surface strongly against hard objects, otherwise it may discolor.

When the temperature goes up to 70 degrees centigrade, paper will discolor.

Don’t use or store paper under high temperature, high humidity and strong light conditions.

2.3.2 Mark paper

In mark paper mode, BTP-R180II determines the cut position and the initial printing position by referencing

the position of the black mark. Black marked paper should meet the following requirement besides that of

standard paper.

3mm≤L1(mark width)≤13mm.

L2(mark length) ≥10mm.

20mm≤L3(distance between two marks) <500mm.

Mark position: left side (only 80mm paper available) or middle of paper.

Reflectivity: The reflectivity of the black mark must be less than 15% while the reflectivity of the paper

itselfexceeds 85%. Thereshall be noprinted objects like text and images in the area between the black

marks.

Caution:

Theprinter will measurethemarksduring theprinting or feeding process. If thelengths ofthe mark (L1)

is larger than the default value (default: 13mm), the printer will give a paper-end alarm.

BTP-R180II User’s Manual

- 5 -

2.4 Print and tear off position

2.4.1 Print position

L1: Paper holder width: 83.5±0.5mm

L2: Max Print width: 72mm

L3: Distance between left end of print-head and left side of paper house (Fixed) 1.75±1mm

L4: Distance between right end of print-head and right side of paper house(Fixed) 1.75±1mm

L5: Left margin (default:0mm)

L6: Print area width. Can set by command (See Programming Manual)

L7: Right margin (default: 0mm)

2.4.2 Tear off position

L1 (Distance between Top printing line and Tear off position): about 28mm

L2 (Distance between Top printing line and Auto cutting position): about 11.6mm

Andere Handbücher für BTP-R180II

Inhaltsverzeichnis

Andere SNBC Drucker Handbücher

SNBC

SNBC BT-T080 Betriebsanleitung

SNBC

SNBC KIOSK Series Bedienungsanleitung

SNBC

SNBC BT-UC156 Bedienungsanleitung

SNBC

SNBC BTP-R880NPI Bedienungsanleitung

SNBC

SNBC BTP-R681 Bedienungsanleitung

SNBC

SNBC BTP-M280 Bedienungsanleitung

SNBC

SNBC BTP-R880NP Betriebsanleitung

SNBC

SNBC BTP-R580II Betriebsanleitung

SNBC

SNBC BTP-M280 Bedienungsanleitung

SNBC

SNBC BTP-2002NP Bedienungsanleitung

SNBC

SNBC BTP-L580IIC Bedienungsanleitung

SNBC

SNBC BTP-R990 Bedienungsanleitung

SNBC

SNBC BT-T080R Bedienungsanleitung

SNBC

SNBC BTP-P36 Bedienungsanleitung

SNBC

SNBC BK-S216 Bedienungsanleitung

SNBC

SNBC BTP-R180II Betriebsanleitung

SNBC

SNBC BK-T6112 Bedienungsanleitung

SNBC

SNBC BTP-P33 Bedienungsanleitung

SNBC

SNBC BTP-2002NP Bedienungsanleitung

SNBC

SNBC BT-UC056III Bedienungsanleitung

SNBC

SNBC BTP-R880NP Bedienungsanleitung

SNBC

SNBC BTP-R580 Bedienungsanleitung

SNBC

SNBC BTP-M300 Betriebsanleitung

SNBC

SNBC BTP-R180II Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung