SnowEx SP-7000 Bedienungsanleitung

Assembly Instructions

F51558 REV-A140905

CUSTOMER COPY

Madison Heights, Michigan 48071

800-SALTERS

www.snowexproducts.com

SP-7000

Serial No. 140410300001SP-7000 and higher

2 © TrynEx International 2014 F51558 REV-A140905

Introduction

These Installation Instructions have been designed to guide you while assembling and installing your SnowEx spreader. Follow these instruc-

tions with care to ensure performance and longevity.

Please read and understand the safety warnings associated with the assembly and installation of the spreader before beginning. In addition

the safety information in the these instructions, observe general safety guidelines to maintain your safety and the safety of those around you.

TORQUE CHART

Use this chart as a guide for tightening hardware.

Hand-tighten all fasteners until complete, then tighten to the recommended torque (unless

specied otherwise in these instructions).

TORQUE CHART FT-LB

Fastener Recommended

Torque (ft-lb)

1/4-20 6

5/16-18 13

3/8-16 23

7/16-14 35

1/2-13 55

9/16-12 80

5/8-11 110

3/4-10 200

7/8-9 320

1-8 480

SAFETY ALERT DEFINITION

This Safety Alert Symbol is used to pinpoint characteristics that, if not carefully followed, can create a safety hazard. When you

see this symbol in this manual or on the machine itself, BE ALERT – your safety and the safety of others is involved.

An accident will occur, resulting in Serious Injury or Death if the instructions are not followed.

An accident may occur, resulting in Serious Injury, perhaps Death, if the instructions are not followed.

An accident may occur, resulting in Minor or Moderate Injury if the instructions are not followed.

Important Information; Property or Equipment Damage may result if not followed.

3© TrynEx International 2014 F51558 REV-A140905

Assembly Instructions

STEP 1

Unpack the spreader; remove the axle, tires, tongue, and spinner drive from the pallet, set aside so the main spreader assembly is alone on

the pallet.

STEP 2

Open the Spinner Drive Box. Open and locate the hardware kits.

STEP 3

Remove the lag bolts holding the spreader to the pallet.

AXLE WHEELS TONGUE

SPINNER DRIVEMUD FLAPFENDERS

BATTERY

4 © TrynEx International 2014 F51558 REV-A140905

Assembly Instructions

STEP 4

Lift the spreader and support it to allow installation of the axle and trailer tongue. Once lifted, remove and discard the pallet. As a safeguard,

in addition to the support jacks underneath the spreader, leave the lifting device in place.

STEP 5

Fasten the Axle to the frame.

STEP 6

Mount the wheels, tighten the lug nuts.

STEP 7

Attach the tongue. It bolts directly to the frame and to the hitch mount at the front of the trailer. Connect the leads of the trailer harness to the

control board: Red to “BAT +” and Black to “GROUND”. Put the Hitch Pin and Hair Pin through the clevis.

5© TrynEx International 2014 F51558 REV-A140905

STEP 9

Lower the tongue jack; pin in the vertical position. Remove the supports. Lower the spreader to rest on the tongue jack and the wheels.

STEP 10

Mount the fenders over the wheels.

STEP 11

Attach the ‘mud ap’ to the rear of the fenders. Use the clamp plate on the outside of the mud ap.

Assembly Instructions

STEP 12

Attach the spinner drive: lower the drive onto the pegs at the rear of the frame; secure with the two bolts and nuts from the hardware kit

through the hanger bracket. Plug it into the spinner plug on the side of the frame. Slide the spinner assembly’s hub over the motor shaft and

tighten the two bolts onto the ‘at’ of the shaft.

6 © TrynEx International 2014 F51558 REV-A140905

STEP 13

Install and connect batteries (under cover). Batteries are not included with the spreader. Use the long wires from T30725 to connect the

batteries to each other. Use the short wires to connect to the control board: Red to “BAT +” and Black to “GROUND”. Install the cover when

nished.

STEP 14

Fit Weather Cover over the top of the hopper.

FINISHED

Owner must supply

the batteries. They are

not included with the

spreader.

Assembly Instructions

7© TrynEx International 2014 F51558 REV-A140905

STEP 1

Determine the location of the vehicle’s battery.

STEP 2

Mount the breaker within 12 inches of the battery’s positive terminal.

STEP 4

Connect the negative lead of the harness to the negative terminal of the battery and the positive harness lead to the “AUX” terminal on the

breaker.

STEP 5

Tie the harness to the frame and other harnesses, working from the hitch area to the battery. Keep away from high-temperature and moving

components. Leave the end by the hitch loose so the harness can connect to the plug on the trailer tongue.

STEP 6

Connect the breaker wire to the positive terminal of the battery and the “BAT” terminal of the breaker.

STEP 7

Connect the spreader. Test that the spinner, auger, and vibrator work.

STEP 3

Route the harness from the rear of the vehicle, near the drawbar, to the battery. Leave enough harness free near the hitch to allow connect-

ing to the trailer tongue plug. Keep away from high-temp and moving components

Vehicle Wiring Instructions

View of Battery, Breaker,

Breaker Wire, and

Harness.

FINISHED

8 © TrynEx International 2014 F51558 REV-A140905

Notes

9© TrynEx International 2014 F51558 REV-A140905

Notes

10 © TrynEx International 2014 F51558 REV-A140905

Notes

Inhaltsverzeichnis

Andere SnowEx Streuer Handbücher

SnowEx

SnowEx SP-85 Betriebsanleitung

SnowEx

SnowEx VX-1500 Bedienungsanleitung

SnowEx

SnowEx 7500 Bedienungsanleitung

SnowEx

SnowEx Vee Pro 3000 Bedienungsanleitung

SnowEx

SnowEx SP-65 Betriebsanleitung

SnowEx

SnowEx HELIXX Bedienungsanleitung

SnowEx

SnowEx Sidewalk-Pro SD-95 Bedienungsanleitung

SnowEx

SnowEx VX-3210 Bedienungsanleitung

SnowEx

SnowEx SP-100-1 Bedienungsanleitung

SnowEx

SnowEx V-Pro 32200 Bedienungsanleitung

SnowEx

SnowEx V-Maxx G2 VX-6010 Bedienungsanleitung

SnowEx

SnowEx HELIXX Series Bedienungsanleitung

SnowEx

SnowEx Precision Pro SP-1675 Bedienungsanleitung

SnowEx

SnowEx Bulk Pro SP-1575 Betriebsanleitung

SnowEx

SnowEx SP-65 Betriebsanleitung

SnowEx

SnowEx SP-1675 Bedienungsanleitung

SnowEx

SnowEx SP-1675 Bedienungsanleitung

SnowEx

SnowEx SP-575V Betriebsanleitung

SnowEx

SnowEx SR-210 Betriebsanleitung

SnowEx

SnowEx SP-2200 Bedienungsanleitung

SnowEx

SnowEx VX-3200 Bedienungsanleitung

SnowEx

SnowEx SP-100 Betriebsanleitung

SnowEx

SnowEx VX-4210 Bedienungsanleitung

SnowEx

SnowEx V-Pro SP-2000 Bedienungsanleitung

Beliebte Streuer Handbücher anderer Marken

PEQUEA

PEQUEA GT-100 Bedienungsanleitung

Herculano

Herculano H2RS9 Bedienungsanleitung

Epoke

Epoke SKE8 Bedienungsanleitung

GEA

GEA EL44 Technisches Datenblatt

Boss Snowplow

Boss Snowplow TGS 800 Bedienungsanleitung

Fisher

Fisher EMERSON 168 Series Bedienungsanleitung

Fisher

Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx

TurfEx RS7200 Betriebsanleitung

Fayat Group

Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

Ferris

Ferris Pathfinder Series Bedienungsanleitung

EASTMAN

EASTMAN CR 500 Bedienungsanleitung

Nogueira

Nogueira RoyalFlow-600 Bedienungsanleitung

Buyers

Buyers TGS05B Bedienungsanleitung

Magnum

Magnum V-BOX PV Series Beilage

Meyer's

Meyer's VB280 Bedienungsanleitung

Kramer

Kramer VM-400HDCP Bedienungsanleitung

H&S

H&S 5134 Bedienungsanleitung