Socomec DIRIS DigiBOX A Bedienungsanleitung

When

energy

matters

DIRIS DigiBOX A

Instruction Manual

Safe

Reliable

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 1/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

Introduction: The purpose of this document is to explain the steps of installing the DIRIS DigiBOX A.

Dimensions:

Part Number

Description

USDBPA40ET

DIRIS A-40 Power Analyzer with Ethernet Modbus TCP/IP output and built in web server-

Enclosed in NEMA 4X PC Enclosure prewired with fused voltage conncetions.

USDBPA40RS

DIRIS A-40 Power Analyzer with RS485 output Enclosed in NEMA 4X PC Enclosure prewired

with fused voltage connections.

USDBPA40PR

DIRIS A-40 Power Analyzer with Profibus output Enclosed in NEMA 4X PC Enclosure

prewired with fused voltage connections

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 2/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

Table of Contents

1. Hazards and Warning................................................................................................................5

1.1. Risk of electrocution, burns or explosion ........................................................................3

1.2. Risk of damaging the device .............................................................................................3

1.3. Responsibility .....................................................................................................................4

2. Conduit Hole..............................................................................................................................5

3. Install Mounting Feet to the Back of the Enclosure ...............................................................6

4. Wiring of the system.................................................................................................................6

5. Configuring the DIRIS A-40 ....................................................................................................10

5.1. Configuration using Wizard.............................................................................................10

5.2. Configuration using EasyConfig.....................................................................................10

6. Webview...................................................................................................................................11

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 3/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

1. Hazards and Warnings

The term "device" used in the paragraphs below refers to the DIRIS A-40. The assembly, use, servicing and

maintenance of this product must only be carried out by trained, qualified professionals. SOCOMEC shall not be

held responsible for failure to comply with the instructions in this manual.

1.1.Risk of electrocution, burns or explosion

Only duly authorized and qualified personnel may work or install/uninstall the device.

The instructions are valid together with the specific instructions for the device.

The device is designed only for its intended purpose as set out in the instructions.

Only accessories authorized or recommended by SOCOMEC may be used in association with the

device.

Before proceeding with installation, maintenance, cleaning, disassembly, connection, or maintenance

work, the device and system must be cut off from the mains to avoid electrocution and damaging the

system and device.

This device is not designed to be repaired by the user.

For any questions related to the disposal of the device, please contact SOCOMEC.

Failure to comply with the instructions of the device and this safety information can cause bodily

injury, electric shock, burns, death or damage to property.

1.2.Risk of damaging the device

To ensure that the device operates correctly, make sure that:

The device is correctly installed.

There is a maximum voltage at the voltage measurement input terminals of 520 V AC phase-phase or

300 VAC phase-neutral.

There is a maximum voltage at the auxiliary power supply input terminals of 400 V AC.

The network frequency indicated on the device is observed: 50 or 60 Hz.

Always connect the TE, TR or TF current sensors using the recommended connection cables and

observing the maximum prescribed currents.

When the ambient temperature exceeds +50°C, the minimum temperature rating of the copper cable to

be connected to terminal must be +85°C.

Failure to respect these precautions could cause damage to the device.

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 4/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

1.3.Responsibility

Assembly, connection and use must be carried out in accordance with the installation standards

currently in force.

The device must be installed in accordance with the rules given in this manual.

Failure to observe the rules for installing this unit may compromise the device's intrinsic protection.

The device must be positioned within an installation which complies with the standards currently in

force.

Any cable which needs to be replaced may only be replaced with a cable having the correct rating.

Despite constantly striving for quality in preparing this manual, errors or omissions are always a

possibility and are not the responsibility of SOCOMEC.

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 5/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

2. Conduit Hole

The DIRIS DigiBOX A is shipped without the conduit holes; they will need to be cut on the left side, right side,

and/or the top. See the below drawings for recommended conduit hole locations.

1. Open the enclosure door, unscrew the two right ride screws, and lift the metal plate.

2. Cut the conduit holes only in the locations where conduit fittings will be installed. Conduit hole templates can

be found within the black bag that comes in the box.

3. To maintain the enclosure’s environmental rating, the installer must use conduit hubs/fittings* with the same

environmental rating as the enclosure.

4. Maintain spacing of at least ½ inch between conduit hubs/fittings and uninsulated live conductors.

5. Use “Grounding” conduit fittings* with built-in set screws. Run insulated copper conductors, 16awg or thicker,

from fittings to spar ground terminal blocks.

6. Route incoming voltage conductors at least ¼ inch away from current sensor and signal conductors. Route

current sensor conductors at least ¼ inch away from communication conductors.

7. Use cable ties to secure conductors to each other and to maintain spacing.

Figure 1: Recommended conduit hole locations.

*not supplied by Socomec

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 6/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

3. Install Mounting Feet to the Back of the Enclosure

1. The DIRIS DigiBOX A is shipped with the mounting feet in the bag.

Figure 2: Mounting feet and hardware provided with the DIRIS DigiBOX A.

2. Turn the enclosure so the back side is visible. Then place the mounting feet over the octagon pieces (you can

place the mounting feet horizontally, diagonally, or vertically) and fasten them with the ¼ inch -20 x 0.25 inch

SS, countersunk Phillips drive screws (torque limit is 30 in. lbs.).

Figure 3: Three ways to put the mounting feet on the enclosure (vertical, horizontal, and diagonal).

3. The enclosure is now ready to be mounted vertically (i.e. on a wall) or horizontally (i.e. on a table top).

4. To mount the unit, use #10-32 ¾ inch panhead screws and screw directly in the center of the cross on the

mounting feet.

Figure 4: Red dot indicates where to screw when mounting on surface.

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 7/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

4. Wiring of the system

Before wiring the system, make sure that the fuses are NOT installed. The fuses are to be installed AFTER all

wiring is complete.

Use class 1 conductors and the input voltage must be 480VAC L-L.

Make sure that the metal cover is still open inside the DIRIS DigiBOX A.

1. Behind the metal plate the prewired and the components that need to be wired can be seen.

2. Wire the voltage according to the designated fuse holder (L1, L2, L3, and N).

Figure 5: Wire the voltage based on the labeled fuse holders (note that the fuse holders are empty).

3. To make sure the product has the latest firmware, the product upgrade tool must be used.

a. Plug in a micro USB to the back of the DIRIS A-40.

Figure 6: The micro USB port on the DIRIS A-40.

b. Go to the website to download the Product Upgraded Tool:

https://www.socomec.com/product-upgrade-tool-software_en.html

c. Under the “Firmware” section, download the DIRIS A-40 firmware. Please note that the firmware

downloaded from the website is a zip file but DO NOT unzip the file, just directly upload the

file into Product Upgrade Tool.

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 8/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

Figure 7: The firmware to be downloaded is labeled DIRIS A-40.

d. Once downloaded open the software to get the below screen:

Figure 8: Product Upgrade tool home screen.

e. Click refresh to get the below screen.

Figure 9: Screen after the refresh button is pressed.

Installation and Commissioning Guide DIRIS DigiBOX A

Ref: dcg_A402019us.rev1 Page 9/15

SOCOMEC PM

Installation and Commissioning Guide DIRIS DigiBOX A

f. Click browse and select the firmware folder that was downloaded. If you see the orange symbol that

means the software file selected is the same as the one on the DIRIS A-40 currently. If there is a

green symbol then that means an update is needed. If there is a red symbol it means that the

firmware selected is a lower version than the DIRIS A-40 currently has.

Figure 10: Product upgrade tool screen once the firmware is selected.

g. Click update if needed. Once the firmware is up to date you will see the following screen:

Figure 11: Product Upgrade Tool screen once update is complete.

4. Plug in the RJ12 cables to the DIRIS A-40 and feed the cable out of a conduit hole.

Note: Depending on the DIRIS A-40 purchased you should connect the communication protocol being used

at this point. For more detailed instructions on how to set up the communication protocols please refer to the

DIRIS A-40 instruction manual.

5. Maintain spacing of at least ½ inch between conduit hubs/fittings and uninsulated live conductors. Use cable

ties to secure conductors to each other and to maintain spacing.

Inhaltsverzeichnis

Andere socomec Messgerät Handbücher

socomec

socomec Continental Control Systems MCM MB Series Bedienungsanleitung

socomec

socomec COUNTIS E11 Bedienungsanleitung

socomec

socomec COUNTIS M43 Bedienungsanleitung

socomec

socomec COUNTIS E23 Bedienungsanleitung

socomec

socomec COUNTIS E00 Bedienungsanleitung

socomec

socomec ISOM ALD590 Bedienungsanleitung

socomec

socomec DIRIS A40 Bedienungsanleitung

socomec

socomec COUNTIS E23 Bedienungsanleitung

socomec

socomec DIRIS A20R Bedienungsanleitung

socomec

socomec DIRIS B-10 Bedienungsanleitung

socomec

socomec DIRIS Digiware D-50 Bedienungsanleitung

socomec

socomec COUNTIS E21 Bedienungsanleitung

socomec

socomec COUNTIS E25 Bedienungsanleitung

socomec

socomec DIRIS A20 Bedienungsanleitung

socomec

socomec DIRIS Digiware S Bedienungsanleitung

socomec

socomec COUNTIS E05 Bedienungsanleitung

socomec

socomec FUSERBLOC Bedienungsanleitung

socomec

socomec DIRIS A40 Bedienungsanleitung

socomec

socomec COUNTIS E41 Montageanleitung

socomec

socomec DIRIS Digiware C Series Bedienungsanleitung

socomec

socomec DIRIS A-30 Bedienungsanleitung

socomec

socomec COUNTIS E27 Bedienungsanleitung

socomec

socomec COUNTIS E47 Bedienungsanleitung

socomec

socomec COUNTIS E17 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

socomec DIRIS DigiBOX A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken