Solavis DKC400Y Bedienungsanleitung

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

Sliding Gate Opener

Model: DKC400Y

Installation Manual

WARNING

Read and thoroughly understand all instructions before installing or

operating this automatic gate opener. Failure to do so may cause serious

injury or death. This gate opener produces a high level of force. Stand

clear of the gate opener during operation and always be aware of the

hazards associated with it.

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

Table of Contents

IMPORTANT—READ THIS FIRST.......................................................................................................................... 3

SAFETY ............................................................................................................................................................. 3

PRELIMINARY CHECKS ..................................................................................................................................... 3

2. Main features .............................................................................................................................................. 4

3. Main technical parameters.......................................................................................................................... 5

4. Working principle and main structure......................................................................................................... 5

Installation........................................................................................................................................................... 6

Gate preparation ............................................................................................................................................. 6

Conduit Pipes................................................................................................................................................... 6

Concrete pad ................................................................................................................................................... 7

Anchors................................................................................................................................................................ 7

Operator .......................................................................................................................................................... 7

Installation of tracks (see Fig.3)....................................................................................................................... 8

Magnets for limit switch.................................................................................................................................. 8

6. Connecting................................................................................................................................................... 9

Wiring notes for control board...................................................................................................................... 11

Control............................................................................................................................................................... 13

Adding extra remote controls (Learn):.......................................................................................................... 14

Erase remote controls: .................................................................................................................................. 14

Verify open direction..................................................................................................................................... 15

Set auto-close function.................................................................................................................................. 15

Cancel auto-close function:........................................................................................................................... 16

Pedestrian mode: .......................................................................................................................................... 16

Set width of pedestrian mode:.................................................................................................................. 16

Set auto-close function of pedestrian mode:............................................................................................ 17

Cancel both the width and the auto-close function of pedestrian mode:................................................ 17

Cancel the width of pedestrian mode, but keep the auto-close function of pedestrian mode: .............. 18

Keep the width of pedestrian mode but cancel the auto-close function of pedestrian mode:................ 18

Adjustment of the auto-reverse function: .................................................................................................... 19

Check ................................................................................................................................................................. 19

Maintenance...................................................................................................................................................... 20

Troubleshooting guide ...................................................................................................................................... 21

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

IMPORTANT—READ THIS FIRST WARNING

This gate is dangerous if installed or used improperly. STAY AWAY FROM THE GATE

WHILE IT IS OPERATING. The gate can crush hands, fingers or toes, knock over persons

in the vicinity, and cause death if used improperly. KEEP CHILDREN AND ADULTS WITH

MENTAL IMPAIRMENTS AWAY FROM THE GATE. Children and adults with mental

impairments, who may not recognize the obvious dangers, are at particular risk and must

be kept away from moving parts of this gate. Damage to the gate or improper installation or

maintenance could cause additional hazards.

NEVER USE THE GATE IF IT IS DAMAGED.

SAFETY

This booklet will offer you information you may need to install your gear motor and to

safeguard your safety. However, caution is unquestionably indispensable and nothing is

better than preventing accidents.

WARNING: any repair or adjustment of working machinery is strictly prohibited unless all

the necessary precautions (electrical supply disconnected and motor off) have been taken

in order to avoid possible accidents.

WARNING: any repair must be carried out by qualified people.

WARNING: All moving mechanisms must be provided with suitable protections.

WARNING: Keep the automatic controls out of the reach of children.

WARNING: Command pulses must be given from positions where the gate is visible.

WARNING: Use transmitters only if you can see the gate.

Read carefully the instructions enclosed in this manual.

Keep this booklet in a suitable place well known to all interested people.

PRELIMINARY CHECKS

The following gate characteristics should exist for the opener installation to be successful:

The gate must be balanced

You must be able to carry out manual closing and opening of the gate without

any effort.

Make sure that the gate has a solid structure and that there is no friction points in

its movement.

The weight of the gate should not exceed 600kg.

Turn off all power to the gate opener until installation is completed.

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

2. Main features

The device is used to drive a sliding gate.

Stop and reverse function if the gate is obstructed during operation.

Supports up to 100 remote controls.

User programmable and user erasable remote codes.

Infrared terminal (N.C) is supplied to use.

Auto-close function

Pedestrian mode.

Manual key release design for emergency purposes.

Integrated control board for easier installation

The gate opener can be integrated with an alarm lamp, photocell and other security

devices.

Soft start and soft stop functions to minimise wear and tear on your gate and gate

hardware and ensure quiet and safe operation.

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

3. Main technical parameters

Model Name

DKC400Y

Power supply:

220V ~240V

Motor speed:

1400r/min

Gate moving speed (output gear 24 teeth)

14m/min

Gate moving speed (output gear 19 teeth)

11m/min

Output torque

14N.m

Max. gate weight

600kg

Remote control range

30m

Remote control frequency

433.92mHz

Working temperature

-10°C ~ +55°C

Limit switch

Magnetic or Spring limit switch

Remote Control

Single Button Mode

Auto Close Time

0~45 sec

Noise

less than 62dB

Working Time

90 sec

4. Working principle and main structure

The device is composed of a single-phase motor, worm and worm gear. The main shaft of

the motor rotates the worm with the clutch engaged; the worm rotates the worm gear and

output gear, which pushes the rack attached to the sliding gate, thus moving the gate.

The device is equipped with a thermal protector; the thermal protector will switch off the

motor automatically when the temperature exceeds 120°C and will switch on the motor

when the temperature drops to around 85°C.

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

Installation

This gate opener is a rack driven operator which works by forcing a rack past the driving

gear. An illustration is shown in Figure 1 below. The gate operator should be installed on

the inside of the gate.

Gate preparation

Be sure the gate is properly installed and slides smoothly before installing the gate

operator. The gate must be plumb, level, and move freely. Manually open and close the

gate, checking for any friction points.

Fig.1

Conduit Pipes

PVC conduit pipes should be used to protect electrical cabling. Ideally, the conduit pipes

should be set into the concrete when it is poured. Ensure that all cables are protected from

sharp or rough objects to avoid any damage.

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

Concrete pad

The base of the unit should be installed on a concrete slab/pad to ensure proper stability.

The concrete pad should be approximately 300mm x 200mm x 200mm deep to ensure

proper operation.

Anchors

You can use the anchors, bolts, washers and nuts that are provided with the operator.

These anchors must be set into the concrete when it is poured. You can also use other

ground anchors such as Dynabolts ™to install in existing concrete.

Operator

In locations where frost occurs, mount the gate operator on an installation pad as shown in

Fig.2. Check the operator and make sure it is lined up with the gate.

Nut

Bolt

Anchor

Nut

Spring washer

Plain washer

Gear

Gate operator

Installation pad

Conduit

Wires

Fig.2

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

Installation of tracks (see Fig.3)

Fix the three nuts (included with the metal tracks) on the rack element.

Lay the first piece of track on the gear and weld the first nut on the gate.

Move the gate manually, checking making sure the track isn’t resisting movement at the

gear, and weld the second and third nut.

Place the second metal track near the first one. Move the gate manually and weld the

three nuts as per the first track. Repeat until the gate is fully covered.

When the rack has been installed, ensure that it rolls smoothly on the driving gear.

The space between rack and gear should be about 1mm.

Fig.3

Magnets for limit switch

For added safety, it is recommended that limit devices such as a ground stop be placed at

both ends of the gate to prevent the gate from sliding out of its rails. This is only a

precaution; the gate operator actually uses a magnetic limit switch to control the open and

closed positions of the gate.

Install the magnet as shown in Fig.4 and Fig.5.

Release the gear clutch and push the sliding gate manually to pre-determine the

positions of the limit switch magnets.

Fix the magnet brackets to the rack and tighten the gear clutch. The lower bracket is

used as the opening limit switch and should be installed on the rack for the open

position. Similarly, the higher magnet is for the closed position. Adjust the position of

gate operator, the magnet should be 10~15mm away from the magnetic limit switch

to work correctly.

Now open and close the gates via the operator. Make final adjustments to the

position of the magnets to ensure that your open and closed gate positions are

correct.

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

10-15mm

Magnet

Gate

Nut

Rack

Gear

Guide rail

122mm

Magnetic limit

switch inside

Fig.4

Fig.5

6. Connecting

Make sure that the power is OFF before making any electrical connections.

Perform the wiring (See Fig.6 and wiring notes for control board).

DKC400Y AC Sliding Gate Installation Manual www.solavis.com.au

Fig.6 Control board scheme

Inhaltsverzeichnis

Beliebte Toröffner Handbücher anderer Marken

Elite

Elite CSW200UL Bedienungsanleitung

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Chamberlain

Chamberlain MotorLift HC280ML Bedienungsanleitung

SOMFY

SOMFY Dexxo RTS Pro Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung