Soleus Air HCC-C09HP-A Bedienungsanleitung

PACKAGED TERMINAL

AIR CONDITIONER with HEAT PUMP

Installation and Operating Instructions

Model No.:HCC-C09HP-A

HCC-C12HP-A

HCC-C15HP-A V140422

CONTENTS

UNIT FEATURES 2

INSTALLATION INSTRUCTION

WIRING 7

MAINTENANCE AND CLEANING 10

NORMAL OPERATING SOUNDS AND CONDITION 12

DIAGNOSTIC CODES 12

TROUBLE SHOOTING 13

… …………………………………………

… …………………………4

… ………………………………………………………

………

… ……………………

………

… …………………………………

………………………………………

OPERATING INSTRUCTIONS 8………

-1-

RECOGNIZE THIS SYMBOL

AS A SAFETY PRECAUTION

WARNING

HIGH VOLTAGE

DISCONNECT ALL POWER BEFORE SERVICING OR

INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY

BE PRESENT, FAILURE TO DO SO MAY CAUSE PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH.

IMPORTANT NOTE TO THE SERVICER

Read this manual and familiarize yourself with the specific

items which must be adhered to before attempting to

service this unit. The precautions listed in this Installation

Manual are intended as supplemental to existing

practices. However, if there is a direct conflict between

existing practices and the content of this manual, the

precautions listed here take precedence.

THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR ANY

INJURY OR PROPERTY, DAMAGE ARISING FROM IMPROPER

SERVICE OR SERVICE PROCEDURES. IF YOU INSTALL OR

PERF O RM S ERV I CE O N THIS UNIT, YOU ASS U ME

RESPONSIBILITY FOR ANY PERSONAL INJURY OR PROPERTY

DAMAGE WHICH MAY RESULT, MANY JURISDICTIONS

REQUIRE A LICENSE TO INSTALL OR SERVICE HEATING AND

AIR CONDITIONING EQUIPMENT.

WARNING

IMPORTANT NOTES:

Before using this manual, check the serial plate for proper

model identification.

The installation and servicing of this equipment must be

performed by qualified, experienced technicians only.

Due to policy of continual product improvement, the right is

reserved to change specifications and design without

notice.

IMPORTANT NOTE TO THE OWNER

This manual is to be used by qualified, professionally trained

HVAC technicians only. The manufacturer does not assume

any responsibility for property damage or personal injury for

improper service procedures or services performed by an

unqualified Person.

• High Pressure Protection The unit will shut off

automatically when the pressure in the system is over

638 psi and within 10 minutes, after the compressor

turns off, the unit will restart when the pressure turns

back below 551 psi. This protection can effectively

avoid the burst and leakage of pipes, lessen the

system failures and prolong the service life.

• Failure Tolerance If the unit is in protection mode

less than 4 times in one hour, the accumulation times

will reset to avoid system failure. Only when the unit

enters protection mode more than 4 times in one

hour, the system will fail to restart automatically and

need manual restart.

•

Standard Physical Dimensions-The series PTAC

is with the same dimensions 42" wide x 16" high x 13-

3/4" deep

Replacement of older units is made easy.

Weather-Protected Electrical Components-Vital

electrical components are protected from the weather

by locating them on the indoor side of the weather

barrier.

Highly Featured Microprocessor Controls-

Microprocessor controls are programmed to interface

with the temperature sensors to maximize comfort

conditions for the room occupant and provide

outstanding features.

Thermistors are used to sense small changes in

temperature to give excellent room control and allow

the microprocessor to monitor and react to changing

conditions.

• Automatic Emergency Heat on Heat Pump

Units-Automatically uses electric resistance heat if

the heat pump fails.

selected room temperatur .

• High-Temperature Heat Pump Operation Protection

-Automatically protects the compressor if heat pump is

operated with high indoor coil temperatures. Power to

the outdoor fan turned off if the

indoor coil gets too hot during heat pump operation to

prevent damage to the compressor.

UNIT FEATURES

This unit has many features which are different than those

found on conventional PTAC units. The servicer must be

familiar with these features in order to properly handle

the unit .

• LCDI Cords-Underwriters Laboratories and the

National Electric Code (NEC) now require power

cords that sense current leakage and can open the

electrical circuit to the unit on units rated at 250 volts

or less. In the event that unit does not operate, check

the reset button located on or near the head of the

power cord as part of the normal troubleshooting

procedure.

LCDI power Cord

• Automatic 3-minute compressor lockout-After

the compressor cycles off, it will not restart for three

minutes.

• Random restart delay-To help eliminate power

surges after a power outage, the unit is equipped with

a two to four minute random restart delay feature.

Whenever the unit is plugged in with the master

switch turned on and the mode switch set in the cool

or heat mode, a random restart will occur. A random

restart condition can be avoided by setting the mode

switch in the fan only or off position before applying

power to the unit.

• Indication LEDs-The control panel has LEDs that

correspond to fan operation and to indicate unit

status. The LEDs next to the selections ON/OFF,

FAN, COOL, and HEAT indicate which operational

-2-

HEAT

COOL

FAN ON/OFF

AUTO

LOW

HIGH

SPEED

FAN

• Fan Motors Permanently Lubricated-All units

have two fan motors for quiet operation and maximum

operating efficiency.

Motors are permanently lubricated to reduce

maintenance and totally enclosed to keep dirt and

water out of the motor windings.

• Indoor Fan Speed Selections LOW /HIGH-Unit

may be operated in low fan speed or high fan speed.

Some speed may not be present based on unit

capacities.

• Rotary Compressor -Smoother operation for quiet,

dependable service and high efficiency.

• Indoor Coil Frost Control-Prevents indoor coil from

freezing. Frost can form on the indoor coil when the unit

is operated in cooling when the outdoor temperature is

low. The unit automatically shuts the compressor off

until the indoor coil temperature warms to the point

where frosting will no longer occur. Then restart the

compressor.

UNIT ACCESSORIES

This unit is designed for through-the-wall installation in

new or existing buildings. To complete the installation

of this PTAC, an insulated wall sleeve and an outdoor

grille (either the stamped aluminum grille, or the

architectural grille ) are required.

The chassis and the cabinet front are shipped in one

carton. Optional accessories to complete a particular

installation are the following:

OPTIONAL ACCESSORIES

Power switch Kit

Wall Sleeve Kit

Key Lock Kit

Drain Kit

Filter Kit

Hard Wire Kit

Wire Harness Kit

Architectural Grille Kit

Stamped Louver Kit

LCDI Power Cord

Wireless IR Antenna

Wireless IR Thermostat

Electric And Non Electric Sub Base Kit

IR REMOTE CONTROLLER

NOTE: Consult sales literature for the appropriate

voltage and amperage selections, if applicable.

-3-

WARNING

HIGH VOLTAGE

DISCONNECT ALL POWER BEFORE SERVICING OR

INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY

BE PRESENT, FAILURE TO DO SO MAY CAUSE PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH.

-4-

WARNING

HIGH VOLTAGE

DISCONN ECT A LL POWER BEF ORE SERVICING OR

INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY

BE PRESENT, FAILURE TO DO SO MAY CAUSE PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH.

INSTALLATION INSTRUCTIONS

To ensure that the unit operates safely and efficiently, it must be installed, operated and maintained according

to these installation and operating instructions and all local codes and ordinances or, in their absence, with the

latest edition of the National Electric Code. The proper installation of this unit is described in the following

sections. Following the steps in the order presented should ensure proper installation.

WALL SLEEVE ASSEMBLY (OPTIONAL ACCESSORY)

Two kinds of wall sleeve are optional for customers, one is reassemble wall sleeve and the other one is

welding integrated wall sleeve.

Removable Wall Sleeve

The removable wall sleeve can be removed and occupies less space and is convenient to transport. Follow the

below steps to install :

a) Unpack all parts and accessories, referring to Fig 1.

b) Assemble the wall sleeve by first “clip locking” the side pieces to the bottom piece.

c) Assemble the top piece to the assembled side and top piece.

Welded integrated wall sleeve

Welded integrated wall sleeve is featured by artistic appearance and stable structure referring to Fig 2.

Customers can purchase together with unit.

Fig 1

Front and discharge grille

Electric heater

Indoor Fan

Display Module

Outdoor Fan

Wall sleeve

Indoor coil

Control box

Power cord coverplate(not show)

Rotary compressor

Outdoor coil

Outdoor grille

Fig 2

42"

16"

In order for condensate water to drain properly inside the

unit, the sleeve must be installed properly:

Level from right to left.

A slight downward pitch from the indoor side to the

out-door side as shown below .

•

(Fig 6)

• Fasten the wall sleeve(Fig 7).

-5-

SLEEVE INSTALLATION

Preparation of the wall

The sleeve should be installed during construction and

lintels should be used to support the block above the wall

sleeve. The sleeve can not support the load of bricks/

blocks.

For existing construction, wall opening must be created,

the proper dimensions are necessary to avoid use of fillers

or additional framing .The sleeve is modular in height and

width(refer to Fig 5& Chart 2).

Height:

Fits 2 courses concrete block

Fits 6 courses standard brick

Fits 5 courses jumbo brick

Width:

Fit approximately 3 stud spaces.

Wall sleeve location

When making the wall opening, please observe the

following requirement:

A) The air inlet and outlet should be unblocked and the air

can be delivered to every corner of the room

B) Install the unit in places that are away from heat source

or sources of flammable gases.

C) Do not install the unit in places that are subject to strong

dust

D) Do not install the unit in places where the operational

noise and exhausted air might trouble your neighbour.

E) There should be sufficient space margins around the

unit to facilitate maintenance and repairs(refer to Fig 3

and 4)

NO.1

NO.2

minium finished opening

dimensions sleeve dimensions

Height width depth

height width

16-1/4"

16-1/4"16"13-3/4"

(16"/18"/24")

42-1/2"

42-1/4"42"

NOTE: NO.1 means using field supplied sleeve angles

NO.2 means not using field supplied sleeve angles

Fig 4

Fig 3

WOOD

SCREW

MOLLY

OR TOGGLE

BOLT

EXPANSION

ANCHOR

BOLT

MAIN STUD

JACK STUDS HEADER-4"×4"OR

2-2"×4"ON EDGE

16-1/4"MIN

ADJUSTABLE FRAMING TO SECURE

THIS DIMENSION

42-1/4"MIN

SUB-FLOOR

FINISHED FLOOR

CRIPPLE

JACK STUD

Note:Do not remove the stiffener

support from inside the wall case

until the chassis is to be installed.

Fig 5

Inside Outside Level

Wall

Sleeve

Outside

Wall

1/4 Bubble

Tilt to

Outside

Proper Sleeve Tilt

Fig 6

Fig 7

Dimensions Recommended installation clearance

Projection of case into room-1/2"minimum up to1-3/4"maximum

without use of electrical sub-base.

Note: 2-3/8" minmum when sub-base is used.

Height above finished floor or top of carpet-1/2"minimum,

2" recommended without sub-base-3" minimum with sub-base.

Chart 1

Chart 2

Cabinet Front Removal View 2

Cabinet Front Removal View 1

4. Secure the chassis to the wall sleeve using three screws

on each side of the chassis to ensure a proper seal

between the chassis and the wall sleeve. The screws are

supplied in a plastic bag.

IMPORTANT NOTES:

1. The unit is equipped with a rubber grommet mounted

compressor. These grommets are factory set and require

no adjustment.

2. Check the indoor and outdoor grilles for obstructions to

air flow. The unit must be located where curtains, furniture,

trees, or other objects do not block the air flow to and from

the unit. If air is obstructed and/or deflected back into the

unit, the air conditioner compressor may cycle on and off

rapidly. This could damage the compressor or possibly

void the warranty.

-6-

OUTDOOR GRILLE

An outside grille must be installed to direct air flow for

proper unit operation and also protect the outdoor coil. The

grille must be installed before installing the chassis.

When replacing an old chassis with an existing grille or

using a specialized grille in a new installation, please

check with after-sales engineer of supplier to determine if

the new chassis should be used with the nonstandard

specialized grille. An improper outdoor grille can decrease

cooling or heating capacity, increase energy usage and

shorten compressor life and possibly void the warranty.

(OPTIONAL ACCESSORY)

FRONT REMOVAL

1. Grasp the cabinet front.

2. Pull the bottom of the cabinet front away from the

chassis until the retaining clips disengage.

3. Lift the cabinet front off the chassis. Reverse this

procedure to reinstall the cabinet front

Chassis Installation View 1

VOLTAGE MEASUREMENTS

Once the unit is properly wired, measure the unit supply

voltage. Voltage must fall within the voltage utilization

range given in .Chart 3

WIRING

Cord connection to a wall socket is not permitted for 265V

units. All 265V units must be hard wired using the hard

wire kit or make use of the plug in receptacle in the

standard subbase.

230~208V units are equipped with LCDI power cords and

can open the electrical circuit to the unit. In the event the

unit does not operate, check the reset button located on or

near the head of the power cord as part of the normal

trouble shooting procedure.

WARNING

HIGH VOLTAGE

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING

THIS UNIT. MULTIPLE POWER SOURCES BE PRESENT, FAILURE

TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY

OR DEATH.

DO NOT SERVICE THIS UNIT WITHOUT FIRST SHUTTING OFF THE

POWER TO THE UNIT FROM THE CIRCUIT BREAKER AND/OR

REMOVING THE UNIT CORD SET PLUG FROM THE WALL OUTLET.

WARNING

THIS AIR CONDITIONER IS NOT MEANT TO PROVIDE

UNATTENDED COOLING OR LIFE SUPPORT FOR PERSONS

OR ANIMALS WHO ARE UNABLE REACT TO THE FAILURE OF

THIS PRODUCT.

THE FAILURE OF AN UNATTENDED AIR CONDITIONER MAY

RESULT IN EXTREME HEAT IN THE CONDITIONED SPACE

CAUSING OVERHEATING OR DEATH OF PERSONS OR

ANIMALS.

Operating Voltage

Rating

230/208

265

Unit Voltage

Minimum

197

238

Voltage Utilization Range

Maximum

253

292

Chart 3 -Operating Voltage

-7-

RED-24VAC

Purple-LS control

Green-High fan speed

Blue-Reversing valve

Yellow-Compressor

White-Heater

Orange-Low fan speed

Black-Common ground

R LS GH B Y W GL C

WALL MOUNTED THERMOSTAT INTERFACE

Thermostat

WARNING

TO AVOID THE RISK OF PROPERTY DAMAGE, PERSONAL

INJURY OR , USE ONLY COPPER CONDUCTORS.FIRE

WARNING

TO AVOID PROPERTY DAMAGE, PERSONAL INJURY OR

DEATH DUE TO ELECTRICAL SHOCK, DO NOT USE AN

EXTENSION CORD WITH THIS UNIT.

WARNING

TO AVOID THE RISK OF PROPERTY DAMAGE, PERSONAL

INJURY OR FIRE DO NOT INSTALL WITH POWER CORD

STRETCHED OR UNDER A STRAIN AS THIS MAY CREATE

LOOSE PLUG/RECEPTACLE CONNECTION.

WARNING

TO AVOID THE RISK OF PERSONAL INJURY, WIRING TO THE

UNIT MUST BE PROPERLY POLARIZED AND GROUNDED.

Fig 9 wall mounted thermostat wiring

Fig 8 Receptacles/Sub-bases

NOTE: See the “ " before

use the thermostat.

Remote Thermostat Change instructions

Tandem

230/208V 15Amp

265V 15Amp

Perpendicular

230/208V 20 Amp

265V 20 Amp

Large tandem

230/208V 30Amp

265V 30Amp

OPERATING INSTRUCTIONS (ACCESSORY OPTIONAL)

HEAT

COOL

FAN ON/OFF

AUTO

LOW

HIGH

SPEED

FAN

Operation mode buttons

Press these buttons to

select the unit operate on

heat mode, cool mode or fan

mode.

Operation mode indicator

lamps

when the unit operates on

heat or cool or fan mode the

indicator lamps will be

actived.

Digital displayer

On normal operation it indicates room temperature;

When pressing + or - button, it indicates setting temperature ;

On time operation, it indicates timer time;

On failure operation, it indicates failure code.

Fan Speed button

Press this button to select

the fan speed on high, low or

auto.

Fan speed indicator lamp.

Operation status indicator

lamp.

Receiver of IR remote controller signal

ON/OFF button

Press this button to turn the

unit ON or OFF.

WARM button

Pressing this button to set room

temperature warmer.

COOL button

Pressing this button to set room

temperature cooler.

Fig 10 Use of unit mounted control panel

-8-

Fig 11 Use of hand held remote controller

The vent control allows outside air to be drawn into the

conditioned area. This outside air can provide ventilation

when the blower is operating, but it will increase the

heating or cooling load and operating costs.

To obtain access to the vent control

1. Remove the cabinet front (see Front Removal).

2. Remove the shipping screw (if installed) from the vent

door.

3. Remove the label (if present) from over the vent control

lever on the left side of the chassis. Remove the vent door

shipping screw.

4. Rotate the vent control lever to either open or close

the damper.

Remove shipping

screw if present

Fig 13 Shipping Screw Location

TIMER PROCEDURE ( Remote controller)

When cells are inserted, the present time is automatically

set to AM 0:00.EX.:set to AM10:30.

 Open the back cover, push the CLK button .The time

indicator is flickering and can set the present time.

 Press the HOUR button.(set to AM 10:00)

 Press the MIN button.(set to 30)

 Press the CLK button again, and then close the back

cover.

COOL/FAN/HEAT MODE OPERATION

PROCEDURE

Control panel:

 Press the ON/OFF button.

 Press the HEAT COOL FAN button, select the operation

mode: heat cool fan.

 Press + or - button, to set your desired temperature. The

setting temperature range is 60-90°F(16-32°C).

 Press the FAN SPEED button, to set your desired air

flow rate: high/ low auto.

° °

auto

/ /

Remote controller:

 Press the ON/OFF button with the remote controller

pointing toward the packaged terminal air conditioner.

 Press the MODE button, select the operation mode:

cool/fan/heat.

 Press + or - button, to set your desired temperature. The

setting temperature range is 61-88 F(16-31 C).

 Press the FAN SPEED button, to set your desired air

flow rate:hig/ low/ .

VENTILATION CONTROL

The ventilation control lever is located at left side of unit,

behind front panel.

NOTE: The vent door shipping tape must be removed before

using vent control lever. See Fig 12 and Fig13.

When set at close, only the air inside the room is circulated

and filtered;

When set at open, some outdoor air will be drawn into room,

this will reduce heating or cooling efficiency.

-9-

: unit control panel has control of unit.

: wall thermostat has control of unit.

R1 R2 R4 R5 R6 R7 R8

Heating Temperature Limits(°F)

9086 86 74 92 90 72 90

63 65 72 69 68 60

Cooling Temperature Limits(°F)

Andere Handbücher für HCC-C09HP-A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air PS08-01 Bedienungsanleitung

Soleus Air

Soleus Air 3046364 Bedienungsanleitung

Soleus Air

Soleus Air SG-TTW-09ESE-26 Bedienungsanleitung

Soleus Air

Soleus Air WS3-06E-201 Bedienungsanleitung

Soleus Air

Soleus Air KFH-12/KFH-12-1 Bedienungsanleitung

Soleus Air

Soleus Air PAC12 Bedienungsanleitung

Soleus Air

Soleus Air MAC-8000 Bedienungsanleitung

Soleus Air

Soleus Air WS4-06EW-201 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE Bedienungsanleitung

Soleus Air

Soleus Air PE4-11R-03 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-15ESE Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-22 Betriebsanleitung

Soleus Air

Soleus Air KFIHP-09-ID Bedienungsanleitung

Soleus Air

Soleus Air WCM1-08E-01 Bedienungsanleitung

Soleus Air

Soleus Air KY-32H Bedienungsanleitung

Soleus Air

Soleus Air PH-3-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air SPTAC-09H Bedienungsanleitung

Soleus Air

Soleus Air 000 BTU Evaporative Portable Air Conditioner and... Bedienungsanleitung

Soleus Air

Soleus Air HCC-C09HP-A Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-25ESE-C Bedienungsanleitung

Soleus Air

Soleus Air PSH-08-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air iCongo PSQ-08-01 Bedienungsanleitung

Soleus Air

Soleus Air PSH-09-01 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung